BS-EN-ISO-6410-2-1996 BS-308-1.11-1996.pdf
《BS-EN-ISO-6410-2-1996 BS-308-1.11-1996.pdf》由会员分享,可在线阅读,更多相关《BS-EN-ISO-6410-2-1996 BS-308-1.11-1996.pdf(14页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 6410-2:1996 BS 308-1.11: 1996 Technical drawings Screw threads and threaded parts Part 2: Screw thread inserts The European Standard EN ISO 6410-2:1996 has the status of a British Standard ICS 01.100.20; 21.040 Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 14 06:26:3
2、5 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 6410-2:1996 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 August 1996 BSI 10-1998 The following BSI reference
3、s relate to the work on this standard: Committee reference TDE/4 Draft announced in BSI News August 1996 ISBN 0 580 26185 9 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee TDE/4, Engineering drawing practice, upon which t
4、he following bodies were represented: Atomic Weapons Establishment British Gas plc British Standards Society Drawing Office Material Manufacturers and Dealers Association Electricity Association Gauge and Tools Makers Association HEVAC Association Institution of Chemical Engineers Institution of Eng
5、ineering Designers Power Generation Contractors Association Society of British Aerospace Companies Ltd. University of Warwick Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 14 06:26:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO
6、6410-2:1996 BSI 10-1998i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Introduction3 1Scope3 2Normative references3 3Representation3 4Designation and dimensioning4 Annex ZA (normative) Normative references to international publications with their relevant Europ
7、ean publications8 Figure 13 Figure 23 Figure 33 Figure 45 Figure 57 Figure 67 Figure 77 Table 16 List of referencesInside back cover Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 14 06:26:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 6410-2:1996 ii BSI 10-1998 National foreword This
8、British Standard has been prepared by Technical Committee TDE/4 and is the English language version of EN ISO 6410-2:1996 Technical drawings Screw threads and threaded parts Part 2: Screw thread inserts, published by the European Committee for Standardization (CEN). It is identical with ISO 6410-2:1
9、993 published by the International Organization for Standardization (ISO). This British Standard partially supersedes BS 308-1. It is envisaged that when the full range of European Standards on technical drawing is implemented BS 308 will be withdrawn. A British Standard does not purport to include
10、all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred toCorresponding British Standard EN 20225:1991 (IS
11、O 225:1983) BS EN 20225:1992 Fasteners. Bolts, screws, studs and nuts. Symbols and designations of dimensions BS EN ISO 6410 Technical drawings Screw threads and threaded parts EN ISO 6410-1:1996 (ISO 6410-1:1993) BS EN ISO 6410-1:1996 General conventions Summary of pages This document comprises a f
12、ront cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed C
13、opy: sheffieldun sheffieldun, na, Tue Nov 14 06:26:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 6410-2 April 1996 ICS 01.100.20; 21.040 Descriptors: Drawings, technical drawings, screw threads, threaded parts, graphic methods English version
14、Technical drawings Screw threads and threaded parts Part 2: Screw thread inserts (ISO 6410-2:1993) Dessins techniques Filetages et pices filetes Partie 2: Inserts filets (ISO 6410-2:1993) Technische Zeichnungen Gewinde und Gewindeteile Teil 2: Gewindeeinstze (ISO 6410-2:1993) This European Standard
15、was approved by CEN on 1996-03-02. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nati
16、onal standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and no
17、tified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United King
18、dom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN ISO 6410-2:1996 E Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 14 06:26:35
19、GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 6410-2:1996 BSI 10-1998 2 Foreword The text of the International Standard from Technical Committee ISO/TC 10, Technical drawings, product definition and related documentation, of the International Organization for Standardization (ISO) has been taken
20、 over as a European Standard by the Technical Board of CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 1996, and conflicting national standards shall be withdrawn at the latest by Oct
21、ober 1996. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal
22、, Spain, Sweden, Switzerland and the United Kingdom. NOTENormative references to International Standards are listed in annex ZA (normative). Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 14 06:26:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 6410-2:1996 BSI 10-19983 Introduction ISO 641
23、0 has been devised to provide a universal means of communication among the various interests involved in the design, manufacture and installation of fasteners. Requirements within industries vary considerably; in recognition of this fact, ISO 6410 is presented in three parts. 1 Scope This part of IS
24、O 6410 specifies methods for the representation of screw thread inserts on technical drawings. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 6410. At the time of publication, the editions indicated w
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-EN-ISO-6410-2-1996 BS-308-1.11-1996 BS EN ISO 6410 1996 308 1.11
链接地址:https://www.31doc.com/p-3748094.html