《BS-ISO-6099-2001.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-6099-2001.pdf(68页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 6099:2001 Fluid power systems and components Cylinders Identification code for mounting dimensions and mounting types ICS 23.100.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00
2、 2006, Uncontrolled Copy, (c) BSI BS ISO 6099:2001 This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 28 September 2001 BSI 28 September 2001 ISBN
3、 0 580 37768 7 National foreword This British Standard reproduces verbatim ISO 6099:2001 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee MCE/18, Fluid power systems and components, which has the responsibility to: A list of
4、organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International St
5、andards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Sta
6、ndard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and Europ
7、ean developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to v, a blank page, pages 1 to 59 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issue
8、d. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Reference number ISO 6099:2001(E) OSI 1002 INTERNATIONAL STANDARD ISO 6099 Third edition 2001-09-01 Fluid power systems and componen
9、ts Cylinders Identification code for mounting dimensions and mounting types Transmissions hydrauliques Vrins Code didentification des dimensions de montage et des modes de fixation Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii Licensed
10、Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E) iii ContentsPage Foreword.iv Introduction.v 1Scope 1 2Normative reference1 3Terms and definitions .1 4Reference point2 4.1General2 4.2Plain rod end2 4.3Pin rod end.2 4.4Female threaded
11、rod end2 4.5Male threaded rod end 3 4.6Wrench flat piston rod end.3 4.7Flanged piston rod end Alternative reference points3 5Letter code for identifying cylinder mounting, envelope and accessory dimensions.4 5.1General4 5.2Letter Z4 5.3Letter U .4 5.4Letters W, X, Y, Z.4 5.5Signs .4 5.6Dimensioning.
12、4 6Identification code for accessory types7 6.1General7 6.2Accessory types 7 7Letter codes of accessories according to accessory type .8 8Identification code for mounting types .12 8.1General12 8.2Mounting types 13 9Letter codes of mounting and envelope dimensions according to cylinder mounting type
13、.15 10Letter code listing36 11Identification statement (Reference to this International Standard).37 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E) iv Foreword ISO (the International Organization for Standardization) is a w
14、orldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented
15、on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafte
16、d in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. A
17、ttention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 6099 was prepared by Technical Committee ISO/TC 131, Fluid po
18、wer systems, Subcommittee SC 3, Cylinders. This third edition cancels and replaces the second edition (ISO 6099:1985), which has been technically revised. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E) v Introduction In flu
19、id power systems, power is transmitted and controlled through a fluid (liquid or gas) under pressure within an enclosed circuit. Systems and their components are generally designed and marketed for a specific fluid pressure. One such component is the fluid power cylinder. This is a device which conv
20、erts power into linear mechanical force and motion. It consists of a movable element, i.e. a piston and piston rod, operating within a cylindrical bore. Although this International Standard provides a code and means of dimensioning for cylinder mounting, it is not intended that all dimensions be sta
21、ndardized. The code specified in this International Standard is not to be considered as complete for the development of future interchangeability standards. It establishes uniform descriptions for dimensions and achieves a conformity of language. The code can be used for analogous dimensions when th
22、is involves neither confusion nor misunderstanding. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI INTERNATIONAL STANDARDISO 60
23、99:2001(E) 1 Fluid power systems and components Cylinders Identification code for mounting dimensions and mounting types 1Scope This International Standard establishes a convention for the identification of mounting dimensions and types used in the mounting of fluid power cylinders. It specifies a c
24、ode for identifying cylinder mounting, envelope, accessory and connector dimensions, and for cylinder mounting and accessory types. This International Standard does not represent a standard list of all fluid power cylinder mounting and accessory types. 2Normative reference The following normative do
25、cument contains provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are enc
26、ouraged to investigate the possibility of applying the most recent editions of the normative document indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 5
27、598, Fluid power systems and components Vocabulary. 3Terms and definitions For the purpose of this International Standard, the terms and definitions given in ISO 5598 apply. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E) 2
28、4Reference point 4.1General Axial dimensions are determined from a reference point that is the same for all cylinders, whatever their mounting method. This theoretical reference point (TRP) is the point of force transfer from the piston rod to the movable element. 4.2Plain rod end For a plain rod en
29、d, the reference point is located on the rod centreline at the end of the piston rod. See Figure 1. Figure 1 ? Plain rod end 4.3Pin rod end For a pin rod end, the reference point is located at the intersection of the pin and piston rod centrelines. See Figure 2. Figure 2 ? Pin rod end 4.4Female thre
30、aded rod end For a female threaded rod end, the reference point is located on the rod centreline at the end of the piston rod. See Figure 3. Figure 3 ? Female threaded rod end Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E)
31、3 4.5Male threaded rod end For a male threaded rod end, the reference point is located on the rod centreline, at the shoulder level. See Figure 4. Figure 4 ? Male threaded rod end 4.6Wrench flat piston rod end For a wrench flat piston rod end, the reference point is located on the wrench flat centre
32、line and the piston rod centreline. See Figure 5. Figure 5 ? Wrench flat rod end 4.7Flanged piston rod end Alternative reference points For a flanged piston rod end, the reference point is either located on the rod centreline at the end of the piston rod (see Figure 6) or on the rod centreline at th
33、e shoulder level (see Figure 7). Figure 6 ? Flanged piston rod end with TRP at the end of the piston rod Figure 7 ? Flanged piston rod end with TRP at the shoulder level Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E) 4 5Let
34、ter code for identifying cylinder mounting, envelope and accessory dimensions 5.1General The code for identifying cylinder mounting, envelope and accessory dimensions is composed of one or two letters and, in some cases, the signs +, + or +/. The meaning of these letters and signs is given in 5.2 to
35、 5.5. 5.2Letter Z Any group of two letters beginning with Z identifies a longitudinal envelope dimension. 5.3Letter U Any group of two letters beginning with U identifies an end view envelope dimension. 5.4Letters W, X, Y, Z Any group of two letters beginning with W, X, Y or Z identifies a dimension
36、 end from the reference point. 5.5Signs The sign + after letters means that the stroke is to be added: ZJ + = ZJ plus stroke. The sign + after letters means that twice the stroke is to be added: ZM + = ZM plus twice the stroke. The sign +/ after letters means that half the stroke is to be added: XV
37、+/ = XV plus half the stroke. 5.6Dimensioning The general dimensions are shown in Figure 8, while the rod-end dimensions are shown in Figure 9. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E) 5 Figure 8 ? Arrangement of gene
38、ral cylinder dimensions Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E) 6 Figure 9 ? Rod end dimensions Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001
39、(E) 7 6Identification code for accessory types 6.1General The identification code for cylinder accessory types consists of two letters and a number. EXAMPLE 6.2Accessory types The accessory types defined in this International Standard are given with their identification code in Table 1. Table 1 Acce
40、ssory types Identification code Description Figure AA4Pivot pin, plain20 AA6Pivot pin, spherical bearing21 AA7Pivot pin, spherical bearing, locking plate22 AB2Eye bracket13 AB3Clevis bracket, in angle15 AB4Clevis bracket, straight14 AB5Clevis bracket, spherical eye, in angle17 AB6Clevis bracket, sph
41、erical eye, straight16 AB7Eye bracket, in angle24 AF3Rod flange, circular18 AL7Locking plate for pivot pin23 AP2Rod clevis, female thread10 AP4Rod eye plain, female thread11 AP6Rod eye spherical, female thread12 AT4Trunnion bracket19 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GM
42、T+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E) 8 7Letter codes of accessories according to accessory type The letter code for accessories according to type is shown in Figures 10 to 24. Figure 10 AP2: Rod clevis, female threadFigure 11 AP4: Rod eye plain, female thread Figure 12 AP6: Rod
43、eye spherical, female threadFigure 13 AB2: Eye bracket Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E) 9 Figure 14 AB4: Clevis bracket, straight Figure 15 AB3: Clevis bracket, in angle Licensed Copy: sheffieldun sheffieldun,
44、 na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E) 10 Figure 16 AB6: Clevis bracket, spherical eye, straight Figure 17 AB5: Clevis bracket, spherical eye, in angle Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c)
45、 BSI ISO 6099:2001(E) 11 Figure 18 AF3: Rod flange, circularFigure 19 AT4: Trunnion bracket Figure 20 AA4: Pivot pin, plainFigure 21 AA6: Pivot pin, spherical bearing Figure 22 AA7: Pivot pin, spherical bearing, locking plate Key 1Screw Figure 23 AL7: Locking plate for pivot pin Licensed Copy: sheff
46、ieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E) 12 Figure 24 AB7: Eye bracket, in angle 8Identification code for mounting types 8.1General The identification code for cylinder mounting types consists of two or three letters and a number. EXAMPL
47、ES The following letters may be used in place of the letter designating flanges used in the above examples. LetterMounting type BBody ECap or head FFlange (detachable) PPivot RThreaded nose SFoot or lugs TTrunnion XStuds or tie rods Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:56:23 GMT
48、+00:00 2006, Uncontrolled Copy, (c) BSI ISO 6099:2001(E) 13 8.2Mounting types The mounting types defined in this International Standard are given with their identifying code in Table 2. Table 2 Mounting types Identification code DescriptionFigure MB 1Body, through bolt hole25 MDB 1Body, through bolt
49、 hole Double rod26 MB 2Round, through bolt hole27 MDB 2Round, through bolt hole Double rod28 ME 5Head, rectangular29 MDE 5Head, rectangular Double rod30 ME 6Cap, rectangular31 ME 7Head, round32 MDE 7Head, round Double rod33 ME 8Cap, round34 ME 9Head, square35 MDE 9Head, square Double rod36 ME 10Cap, square37 ME 11Head, square38 MDE 11Head, square Double rod39 ME 12Cap, square40 MF 1Head, rectangular flange41 MDF 1Head, rectangular flange Double rod42 MF 2Cap, rectangular flange43 MF 3Hea
链接地址:https://www.31doc.com/p-3748711.html