BS-EN-ISO-2338-1998.pdf
《BS-EN-ISO-2338-1998.pdf》由会员分享,可在线阅读,更多相关《BS-EN-ISO-2338-1998.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 2338:1998 Parallel pins of unhardened steel and austenitic stainless steel The European Standard EN ISO 2338:1997 has the status of a British Standard ICS 21.060.50 BS EN ISO 2338:1998 This British Standard, having been prepared under the direction of the Engineering Secto
2、r Board, was published under the authority of the Standards Board and comes into effect on 15 May 1998 BSI 03-1999 ISBN 0 580 29089 1 National foreword This British Standard is the English language version of EN ISO 2338:1997. It is identical with ISO 2338:1997. It supersedes BS EN 22338:1992 which
3、is withdrawn. The UK participation in its preparation was entrusted by Technical Committee FME/9, Bolts, nuts and accessories, to Subcommittee FME/9/6, General puropse fasteners and accessories, which has the responsibility to: aid enquirers to understand the text; present to the responsible interna
4、tional/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to it
5、s secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European p
6、ublications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Use
7、rs of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN ISO title page, page 2, the ISO t
8、itle page, page ii, pages 1 to 3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments BS EN ISO 2338:1998 BSI 0
9、3-1999i Contents Page National foreword Inside front cover Foreword 2 Foreword ii Text of EN ISO 2338 1 ii blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 2338 November 1997 ICS 21.060.50Supersedes EN 22338:1992 Descriptors: See ISO document English version Parallel pins, of unhardene
10、d steel and austenitic stainless steel (ISO 2338:1997) Goupilles cylindriques en acier non tremp et en acier inoxydable austnitique (ISO 2338:1997) Zylinderstifte aus ungehrtetem Stahl und austenitischem nichtrostendem Stahl (ISO 2338:1997) This European Standard was approved by CEN on 23 October 19
11、97. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained
12、on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretari
13、at has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN Europe
14、an Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 2338:1997 E EN ISO 233
15、8:1997 BSI 03-1999 2 Foreword The text of the International Standard ISO 2338:1997 has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Threaded and non-threaded mechanical fasteners and accessories”, the secretariat of which is held by
16、DIN. This European Standard supersedes EN 22338:1992. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 1998, and conflicting national standards shall be withdrawn at the latest by May 1998. Acc
17、ording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portug
18、al, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 2338:1997 was approved by CEN as a European Standard without any modification. Contents Foreword 2 1Scope1 2Normative references1 3Dimensions1 4Requirements and reference Internationa
19、l Standards3 5Designation3 Figure 11 Table 1 Dimensions2 Table 2 Requirements and reference International Standards3 EN ISO 2338:1997 ii BSI 03-1999 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work
20、of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-government
21、al, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN ISO 2338 1998
链接地址:https://www.31doc.com/p-3748907.html