BS-QC-301801-1993 IEC-60384-13-1-1991.pdf
《BS-QC-301801-1993 IEC-60384-13-1-1991.pdf》由会员分享,可在线阅读,更多相关《BS-QC-301801-1993 IEC-60384-13-1-1991.pdf(14页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS QC 301801:1993 IEC 384-13-1: 1991 Harmonized system of quality assessment for electronic components Fixed capacitors for use in electronic equipment Blank detail specification Fixed polypropylene film dielectric metal foil d.c. capacitors Assessment level E Licensed Copy: London
2、South Bank University, London South Bank University, Fri Dec 08 17:11:44 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS QC 301801:1993 BSI 03-2000 ISBN 0 580 35801 1 Amendments issued since publication Amd. No.DateComments Licensed Copy: London South Bank University, London South Bank University, Fri
3、 Dec 08 17:11:44 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS QC 301801:1993 BSI 03-2000i Contents Page National forewordii Introduction1 Section 1. General data2 Section 2. Inspection requirements3 Table I2 Table II Values of capacitance and of voltage related to case sizes2 Table III Other charac
4、teristics3 Table IV4 Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 17:11:44 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS QC 301801:1993 ii BSI 03-2000 National foreword This British Standard has been prepared under the direction of the Electronic Components S
5、tandards Policy Committee. It is identical with IEC 384-13-1:1991 (QC 301801) “Fixed capacitors for use in electronic equipment Part 13: Blank detail specification: Fixed polypropylene film dielectric metal foil d.c. capacitors. Assessment level E”, published by the International Electrotechnical Co
6、mmission (IEC) and is a harmonized specification in the IECQ system of quality assessment for electronic components. IEC 384-13-1 was prepared by IEC Technical Committee No. 40, “Capacitors and resistors for electronic equipment” and the United Kingdom participation in the drafting was provided by S
7、ubcommittee ECL/4/4 “Capacitors and electromagnetic suppression components for electronic equipment”, under the direction of Technical Committee ECL/4, “Capacitors and resistors for electronic equipment”. Scope. This standard lists the ratings, characteristics and inspection requirements which shall
8、 be included as mandatory requirements in accordance with BS QC 301800 in any detail specification for these components. The British Standard which implements the IECQ Rules of Procedure is BS 9000 “General requirements for a system for electronic components of assessed quality” Part 3:1991 “Specifi
9、cation for the national implementation of the IECQ System”. Detail Specifications. Detail Specifications shall comply with the requirements of this Blank Detail Specification and BS QC 001002:1991 “Rules of Procedure of the IEC Quality Assessment System for Electronic Components (IECQ)”. A British S
10、tandard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International StandardCorresponding
11、 British Standard IEC 384-1:1982 Amendment No. 2:1987 BS QC 300000:1983 Fixed capacitors for use in electronic equipment. Generic specification (Identical) IEC 384-13:1991BS QC 301800:1991 Harmonized system of quality assessment for electronic components. Fixed capacitors for use in electronic equip
12、ment. Sectional specification for fixed polypropylene film dielectric metal foil d.c. capacitors (Identical) IEC 410:1973BS 6001: Sampling procedures for inspection by attributes Part 1:1991 Specification for sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection (Technic
13、ally equivalent) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 9 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside fro
14、nt cover. Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 17:11:44 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS QC 301801:1993 BSI 03-20001 Introduction Blank detail specification A blank detail specification is a supplementary document to the Sectional Specifi
15、cation and contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they so be described. In the preparation of detail specificat
16、ions the content of Sub-clause 1.4 of the sectional specification shall be taken into account. The numbers between brackets on the first page correspond to the following information which shall be inserted in the position indicated: Identification of the detail specification 1) The “International El
17、ectrotechnical Commission” or the National Standards Organisation under whose authority the detail specification is drafted. 2) The IEC or National Standards number of the detail specification, date of issue and any further information required by the national system. 3) The number and issue number
18、of the IEC or national Generic Specification. 4) The IEC number of the blank detail specification. Identification of the capacitor 5) A short description of the type of capacitor. 6) Information on typical construction (if applicable). NOTEWhen the capacitor is not designed for use in printed board
19、applications, this shall be clearly stated in the detail specification in this position. 7) Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an app
20、endix to the detail specification. 8) Application or group of applications covered and/or assessment level. NOTEThe assessment level(s) to be used in a detail specification shall be selected from the sectional specification, Sub-clause 3.5.4. This implies that one blank detail specification may be u
21、sed in combination with several assessment levels, provided the grouping of the tests does not change. 9) Reference data on the most important properties, to allow comparison between the various capacitor types. (1) IEC 384-13-1-XXX QC 301801-XXX (2) ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCO
22、RDANCE WITH: IEC 384-13-1 QC 301801 (4) (3) FIXED POLYPROPYLENE FILM DIELECTRIC METAL FOIL D.C. CAPACITORS (5) Outline drawing: (see Table I ) (. angle projection) (7)(6) (Other shapes are permitted within the dimensions given) Assessment level(s): E(8) Stability class: . Information on the availabi
23、lity of components qualified to this detail specification is given in the Qualified Products List (9) Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 17:11:44 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS QC 301801:1993 2 BSI 03-2000 Section 1. General data 1.1
24、Recommended method(s) of mounting (to be inserted) (See Sub-clause 1.4.2 of IEC Publication 384-13). 1.2 Dimensions Table I NOTE 1When there is no case size reference, Table I may be omitted and the dimensions shall be given in Table II, which then becomes Table I. NOTE 2The dimensions shall be give
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-QC-301801-1993 IEC-60384-13-1-1991 BS QC 301801 1993 IEC 60384 13 1991
链接地址:https://www.31doc.com/p-3749035.html