《BS-EN-607-1996.pdf》由会员分享,可在线阅读,更多相关《BS-EN-607-1996.pdf(16页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 607:1996 Eaves gutters and fittings made of PVC-U Definitions, requirements and testing The European Standard EN 607:1995 has the status of a British Standard ICS 91.140.80 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 15:59:55 GMT+00:00 2006, Uncontrolled Copy, (c) B
2、SI BS EN 607:1996 This British Standard, having been prepared under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 February 1996 BSI 08-1999 The following BSI references relate to the work on this st
3、andard: Committee reference PRI/61 Draft for comment 92/37684 DC ISBN 0 580 25155 1 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PRI/61, Plastics piping systems and components, upon which the following bodies were repr
4、esented: British Gas plc British Plastics Federation British Plumbing Fittings Manufacturers Association British Valve and Actuator Manufacturers Association Department of the Environment (British Board of Agrment) Department of the Environment (Building Research Establishment) Department of the Env
5、ironment (Property and Buildings Directorate) Department of Transport Electricity Association Federation of Civil Engineering Contractors Health and Safety Executive Institute of Building Control Institute of Materials Institution of Civil Engineers Institution of Gas Engineers Institution of Water
6、and Environmental Management National Association of Plumbing, Heating and Mechanical Services Contractors Pipeline Industries Guild Plastics Land Drainage Manufacturers Association Society of British Gas Industries Society of British Water Industries Water Companies Association Water Services Assoc
7、iation of England and Wales The following bodies were also represented in the drafting of the standard, through subcommittees and panels: British Adhesives and Sealants Association Institute of Plumbing Land Drainage Contractors Association National Association of Agricultural Contractors Amendments
8、 issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 15:59:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 607:1996 BSI 08-1999i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 6073 List of refere
9、nces Inside back cover Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 15:59:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 607:1996 ii BSI 08-1999 National foreword This British Standard has been prepared by Technical Committee PRI/61 and is the English language version of EN 607:1995 E
10、aves gutters and fittings made of PVC-U Definitions, requirements and testing, published by the European Committee for Standardization (CEN). BS EN 607 is potentially a partial revision of BS 4576 Unplasticized polyvinyl chloride) (PVC-U) rainwater goods and accessories: Part 1:1989 Half-round gutte
11、rs and pipes of circular cross section, but the overlap of the scopes of these two standards does not allow for a simple one-to-one revision. BS 4576-1 covers complete systems, based on half-round gutters and circular section downpipes and their respective supports, and associated requirements for i
12、nstallation and testing. BS EN 607 covers gutters of any shape, including half-round, but is dependent upon the completion and implementation of other standards under preparation to cover gutter fixing brackets and rafter arm brackets (to be EN 1462) and to cover rainwater pipes of circular and/or o
13、ther cross sections (to be covered by EN 12200). These complementary standards for BS EN 607 are expected to become available at successive intervals. PRI/61 has therefore concluded that it is not practicable to amend BS 4576-1 piecemeal as each of the partly relevant European Standards is finalized
14、, nor reasonable to withdraw BS 4576-1:1989 in whole or part until sufficient European Standards have been published to provide a package which enables a complete PVC-U rainwater system to be assembled in accordance therewith. The UK did not approve of either pr EN 607 or the final draft for EN 607.
15、 The UK Committee is particularly concerned by the lack of a minimum wall thickness in the absence of a loading test and the lack of interchangability with existing products conforming to BS 4576-1. The Committee is also concerned that Annex C is inadequate. The committee would therefore welcome com
16、ments arising from any aspects of the application of this standard for consideration at the first review of this standard. Product certification. Users of this British Standard are advised to consider the desirability of third party certification of product conformity. Enquiries as to the availabili
17、ty of third party certification schemes are forwarded by BSI to the Association of Certification Bodies. If a third party certification scheme does not already exist, users should consider approaching an appropriate body from the list of Association members. Textual errors. When adopting the text of
18、 the European Standard, the textual errors listed below were discovered. They have been marked in the text and have been reported to CEN in a proposal to amend the text of the European Standard. Clause 2 Normative references Textual errorCorrection EN 638:1992EN 638:1994 EN 727:1992EN 727:1994 prEN
19、743EN 743:1994 prEN 763EN 763:1994 ISO 105-A02:1987ISO 105-A02:1993 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 15:59:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 607:1996 BSI 08-1999iii NOTE 1Reference is also made to ISO/DIS 4892-2. This has since been superseded by publication o
20、f ISO 4892-2:1994, which has been accepted by CEN for publication as EN ISO 4892-2. When that is published it is intended that the corresponding British Standard will carry the references BS EN ISO 4892-2 and BS 2782-5:Method 540E. NOTE 2Reference is also made to ISO/DIS 4892-3. This has since been
21、superseded by publication of ISO 4892-3:1994, which has been accepted by CEN for publication as EN ISO 4892-3. When that is published it is intended that the corresponding British Standard will carry the references BS EN ISO 4892-3 and BS 2782-5:Method 540F. WARNING NOTE. This British Standard, whic
22、h is identical with EN 607:1995, does not necessarily detail all the precautions necessary to meet the requirements of the Health and Safety at Work etc. Act 1974. Attention should be paid to any appropriate safety precautions and the test methods should be operated only by trained personnel. A Brit
23、ish Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred toCorresp
24、onding British Standard EN 638:1994BS EN 638:1995 Plastics piping and ducting systems Thermoplastics pipes Determination of tensile properties (BS 2782:Method 1110B:1995) EN 727:1994BS EN 727:1995 Plastics piping and ducting systems Thermoplastics pipes and fittings Determination of Vicat softening
25、temperature (VST) (BS 2782:Method 1103V:1995) EN 743:1994BS EN 743:1995 Plastics piping and ducting systems Thermoplastics pipes Determination of the longitudinal reversion (BS 2782:Methods 1102A and 1102B:1995) EN 763:1994BS EN 763:1995 Plastics piping and ducting systems Injection-moulded thermopl
26、astics fittings Test methods for visually assessing effects of heating (BS 2782:Methods 1103A and 1103B:1995) ISO 105-A02:1993BS EN 20105-A02:1995 Grey scale for assessing change in colour ISO 8256:1990BS 2782 Methods of testing plastics Part 3 Mechanical properties Methods 354A and 354B:1991 Determ
27、ination of tensile-impact strength Summary of pages This document comprises a front cover, an inside front cover, pages i to iv, the EN title page, pages 2 to 8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This
28、will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 15:59:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 15:59:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN
29、STANDARD NORME EUROPENNE EUROPISCHE NORM EN 607 June 1995 ICS 91.140.80 Descriptors: Roofing, water removal, rain water, eaves gutters, unplasticized polyvinyl chloride, fittings, specifications, definitions, physical properties, tests, operating requirements, designation, marking English version Ea
30、ves gutters and fittings made of PVC-U Definitions, requirements and testing Gouttires pendantes et leurs raccords en PVC-U Dfinitions, exigences et mthodes dessai Hngedachrinnen und Zubehrteile aus PVC-U Begriffe, Anforderungen und Prfung This European Standard was approved by CEN on 1995-06-06. CE
31、N members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on app
32、lication to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has
33、 the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Stand
34、ardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1995 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members. Ref. No. EN 607:1995 E Licensed Copy: she
35、ffieldun sheffieldun, na, Mon Nov 13 15:59:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 607:1995 2 BSI 08-1999 Foreword This European Standard has been prepared by the Technical Committee CEN/TC 128, Roof covering products for discontinuous laying, the secretariat of which is held by IBN. This E
36、uropean Standard shall be given the status of a National Standard, either by publication of an identical text or by endorsement at the latest by December 1995, and conflicting national standards shall be withdrawn at the latest by December 1995. According to the CEN/CENELEC Internal Regulations, the
37、 following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 1Scope3 2Normative reference
38、s3 3Definitions3 4Requirements on the material4 5Gutters, requirements and test methods4 6Fittings, requirements and test methods5 7Gutter seals and solvent cements5 8Designation5 9Marking5 10Fitness for purpose of gutter systems5 Annex A (normative) Impact test7 Annex B (normative) Heat reversion t
39、est for fittings7 Annex C (normative) Watertightness test8 Figure A.1 Arrangement for impact test7 Figure C.1 Arrangement for watertightness test (horizontal projection)8 Table 1 Physical and mechanical properties of gutters4 Table 2 Physical properties of fittings5 Table 3 Requirements for gutter s
40、ystems6 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 15:59:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 607:1995 BSI 08-19993 1 Scope This European Standard specifies requirements and test methods of eaves gutters and fittings made from unplasticized polyvinyl chloride (PVC-U), and int
41、ended to be used for rainwater drainage. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated refer
42、ences, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 638:1992, Plastics piping and ducting systems Thermopl
43、astics pipes Determination of short term tensile properties1). EN 727:1992, Plastics piping and ducting systems Thermoplastics pipes and fittings Determination of Vicat softening temperature1). prEN 743, Plastics piping and ducting systems Thermoplastics pipes Determination of the longitudinal rever
44、sion1). prEN 763, Thermoplastics piping and ducting systems Injection-moulded fittings Test methods for visually assessing effects of heating1). ISO 105-A02:1987, Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour1). ISO/DIS 4892-2, Plastics Methods of exposure to
45、 laboratory light sources Part 2: Xenon arc sources. ISO/DIS 4892-3, Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent lamps. ISO 8256:1990, Plastics Determination of tensile impact strength. 3 Definitions For the purposes of this European Standard the following definition
46、s apply. 3.1 Components 3.1.1 eaves gutter a gutter situated outside the building and supported by brackets 3.1.2 down-pipe a pipe fitted to a gutter to lead rainwater from the gutter to the drainage system or sewer 3.1.3 union-clip (gutter-union) a fitting for joining two gutters and supported only
47、 by those gutters 3.1.4 joint-bracket (union-bracket) a fitting for joining two gutters which is supported by the building structure 3.1.5 gutter adaptor a fitting for joining two different shaped gutters 3.1.6 angle a fitting for joining two gutters installed in two different directions 3.1.7 stop
48、end a fitting for stopping the flow, fixed at the end of a gutter or an outlet 3.1.8 outlet a fitting for draining off the rainwater from the gutter into the down-pipe 3.1.9 commercial length the length of a gutter or a down-pipe which was produced in a factory 3.2 Material 3.2.1 virgin material a m
49、aterial in a form of granules or powder that has not been subjected to use or processing other than that required for their manufacture and to which no reprocessable or recyclable materials have been added 3.2.2 own reprocessable material material prepared from rejected unused profiles and fittings, including trimmings from the production of profiles and fittings, that will be reprocessed in a manufacturers plant after having been previously processed by the same manufacturer by a process such as
链接地址:https://www.31doc.com/p-3749097.html