BS-ISO-5675-2008.pdf
《BS-ISO-5675-2008.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-5675-2008.pdf(14页珍藏版)》请在三一文库上搜索。
1、BS ISO 5675:2008 ICS 65.060.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Agricultural tractors and machinery General purpose quick-action hydraulic couplers Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:50, Uncontrolle
2、d Copy, (c) BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 2008 BSI 2008 ISBN 978 0 580 57779 6 Amendments/corrigenda issued since publication DateComments BS ISO 5675:2008 National foreword This British Standard is the UK implementation
3、 of ISO 5675:2008. It supersedes BS 4742-2:1993 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee AGE/6, Agricultural tractors and forestry machinery. A list of organizations represented on this committee can be obtained on request to its secretary. Thi
4、s publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. 30 September Licensed Copy: London South Bank University, South Bank University,
5、16/11/2008 11:50, Uncontrolled Copy, (c) BSI BS ISO 5675:2008 INTERNATIONAL STANDARD ISO 5675 Third edition 2008-08-01 Reference number ISO 5675:2008(E) ISO 2008 Agricultural tractors and machinery General purpose quick-action hydraulic couplers Tracteurs et matriels agricoles Coupleurs hydrauliques
6、 usage gnral Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:50, Uncontrolled Copy, (c) BSI BS ISO 5675:2008 ISO 5675:2008(E) ii ISO 2008 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, thi
7、s file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secreta
8、riat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensur
9、e that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication
10、 may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 T
11、el. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:50, Uncontrolled Copy, (c) BSI BS ISO 5675:2008 ISO 5675:2008(E) ISO 2008 All rights reserved iii Foreword IS
12、O (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical co
13、mmittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electro
14、technical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the me
15、mber bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identif
16、ying any or all such patent rights. ISO 5675 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 4, Tractors. This third edition cancels and replaces the second edition (ISO 5675:1992), which has been technically revised. Licensed Copy:
17、 London South Bank University, South Bank University, 16/11/2008 11:50, Uncontrolled Copy, (c) BSI BS ISO 5675:2008 . iv Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:50, Uncontrolled Copy, (c) BSI BS ISO 5675:2008 INTERNATIONAL STANDARDISO 5675:2008(E) ISO 2008 A
18、ll rights reserved 1 Agricultural tractors and machinery General purpose quick- action hydraulic couplers 1Scope This International Standard specifies the essential interface dimensions, as defined in ISO 7241-1, and the operating requirements for hydraulic couplers employed to transmit hydraulic po
19、wer from agricultural tractors to agricultural machinery. It is applicable to couplers used in hydraulic lines other than those used for braking circuits (see ISO 5676). NOTEAll hydraulic couplers need to be connected and disconnected frequently to allow the transfer of machinery from one tractor to
20、 another without the use of tools or special devices. 2Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includin
21、g any amendments) applies. ISO 7241-1:1987, Hydraulic fluid power Quick-action couplings Part 1: Dimensions and requirements ISO 7241-2:2000, Hydraulic fluid power Quick-action couplings Part 2: Test methods 3Terms and definitions For the purposes of this document, the following terms and definition
22、s apply. 3.1 coupler female part female part part that has a cavity to receive the male part 3.2 coupler male part male part probe that fits and locks into the cavity of the female part 4Requirements 4.1Dimensional requirements The dimensions of the coupler male part shall be in accordance with ISO
23、7241-1:1987, Table 1 and Figure 1, series “A”, for sizes 12,5 and 20. In addition, the coupler male part dimension shall be in accordance with Figure 1 and Table 1 of this International Standard, in order to be compatible with dust protection devices. Licensed Copy: London South Bank University, Sou
24、th Bank University, 16/11/2008 11:50, Uncontrolled Copy, (c) BSI BS ISO 5675:2008 ISO 5675:2008(E) 2 ISO 2008 All rights reserved Any female part shall couple with any male part when both conform to this International Standard. 4.2Operating requirements 4.2.1The coupler shall be in accordance with t
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS ISO 5675 2008
链接地址:https://www.31doc.com/p-3749811.html