BS-ISO-11414-2009.pdf
《BS-ISO-11414-2009.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-11414-2009.pdf(18页珍藏版)》请在三一文库上搜索。
1、BS ISO 11414:2009 ICS 23.040.60 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/ fitting test piece assemblies by butt fusion Licensed CopyChinese University of Hong Kong, 11/04/200
2、9 08:32, Uncontrolled Copy, (c) BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2009 BSI 2009 ISBN 978 0 580 60187 3 Amendments/corrigenda issued since publication DateComments BS ISO 11414:2009 National foreword This British
3、Standard is the UK implementation of ISO 11414:2009. It supersedes BS 2782 11 MET1150 :1998 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRI/88/4, Test methods. A list of organizations represented on this committee can be obtained on request to its
4、 secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. -B Licensed CopyChinese University of Hong Kong, 11/04/2009 08:32,
5、 Uncontrolled Copy, (c) BSI BS ISO 11414:2009 Reference number ISO 11414:2009(E) ISO 2009 INTERNATIONAL STANDARD ISO 11414 Second edition 2009-02-01 Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion Tubes et raccords en matire
6、s plastiques Prparation dprouvettes par assemblage tube/tube ou tube/raccord en polythylne (PE) par soudage bout bout Licensed CopyChinese University of Hong Kong, 11/04/2009 08:32, Uncontrolled Copy, (c) BSI BS ISO 11414:2009 ISO 11414:2009(E) PDF disclaimer This PDF file may contain embedded typef
7、aces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infrin
8、ging Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optim
9、ized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Un
10、less otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO
11、 copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reserved Licensed CopyChinese University of Hong Kong, 11/04/2009 08:32, Uncontrolled Copy, (c) BSI BS ISO 11414:20
12、09 ISO 11414:2009(E) ISO 2009 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees.
13、Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internat
14、ional Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Stand
15、ards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subjec
16、t of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11414 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plast
17、ic materials and their accessories Test methods and basic specifications. This second edition cancels and replaces the first edition (ISO 11414:1996), which has been technically revised. Licensed CopyChinese University of Hong Kong, 11/04/2009 08:32, Uncontrolled Copy, (c) BSI BS ISO 11414:2009 Lice
18、nsed CopyChinese University of Hong Kong, 11/04/2009 08:32, Uncontrolled Copy, (c) BSI BS ISO 11414:2009 INTERNATIONAL STANDARD ISO 11414:2009(E) ISO 2009 All rights reserved 1 Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
19、 1 Scope This International Standard specifies a method for preparing butt-fusion-jointed test piece assemblies between polyethylene (PE) pipes and spigot-ended fittings. This International Standard specifies the assembly parameters involved, such as the ambient temperature, joint geometry and fusio
20、n parameters, taking into account the service condition limits specified in the relevant product standards, as well as the type of pipe to be used. This International Standard is intended to enable the effect of site assembly variables on joint performance to be determined. The fusion-jointing proce
21、dures and parameters used in the field can differ from those in this International Standard, depending on the manufacturers written procedures and/or local standards. NOTE The assembly and fusion-jointing technique specified in this International Standard is applicable whatever the polyethylene resi
22、n employed, provided it is used in accordance with ISO/TR 116471. Deviations from the fusion cycle specified, in order to demonstrate joint performance, can be considered in accordance with the notes in Annexes A and B. 2 Normative references The following referenced documents are indispensable for
23、the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4427-2, Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 2: Pipes IS
24、O 4427-3, Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 3: Fittings ISO 4437, Buried polyethylene (PE) pipes for the supply of gaseous fuels Metric series Specifications ISO 8085-2, Polyethylene fittings for use with polyethylene pipes for the supply of gaseous f
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS ISO 11414 2009
链接地址:https://www.31doc.com/p-3750550.html