DD-CEN-ISO2TS-12180-1-2007.pdf
《DD-CEN-ISO2TS-12180-1-2007.pdf》由会员分享,可在线阅读,更多相关《DD-CEN-ISO2TS-12180-1-2007.pdf(28页珍藏版)》请在三一文库上搜索。
1、DRAFT FOR DEVELOPMENT DD CEN ISO/TS 12180-1:2007 Geometrical product specifications (GPS) Cylindricity Part 1: Vocabulary and parameters of cylindrical form ICS 01.040.17; 17.040.20 ? Licensed CopyChinese University of Hong Kong, 20/10/2008 09:34, Uncontrolled Copy, (c) BSI DD CEN ISO/TS 12180-1:200
2、7 This Draft for Development was published under the authority of the Standards Policy and Strategy Committee on 30 May 2008 BSI 2008 ISBN 978 0 580 57986 8 National foreword This Draft for Development is the UK implementation of CEN ISO/TS 12180-1:2007. It is identical with ISO/TS 12180-1:2003. Thi
3、s publication is not to be regarded as a British Standard. It is being issued in the Draft for Development series of publications and is of a provisional nature. It should be applied on this provisional basis, so that information and experience of its practical application can be obtained. Comments
4、arising from the use of this Draft for Development are requested so that UK experience can be reported to the European organization responsible for its conversion to a European standard. A review of this publication will be initiated not later than three years after its publication by the European o
5、rganization so that a decision can be taken on its status. Notification of the start of the review period will be made in an announcement in the appropriate issue of Update Standards. According to the replies received by the end of the review period, the responsible BSI Committee will decide whether
6、 to support the conversion into a European Standard, to extend the life of the Technical Specification or to withdraw it. Comments should be sent to the Secretary of the responsible BSI Technical Committee at British Standards House, 389 Chiswick High Road, London W4 4AL. The UK participation in its
7、 preparation was entrusted to Technical Committee TDW/4, Technical product realization (TPR). A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsi
8、ble for its correct application. Amendments/corrigenda issued since publication DateComments Licensed CopyChinese University of Hong Kong, 20/10/2008 09:34, Uncontrolled Copy, (c) BSI TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN ISO/TS 12180-1 December 2007 ICS 17.040.
9、20; 01.040.17 English Version Geometrical product specifications (GPS) - Cylindricity - Part 1: Vocabulary and parameters of cylindrical form (ISO/TS 12180- 1:2003) Spcification gomtrique des produits (GPS) - Cylindricit - Partie 1: Vocabulaire et paramtres de cylindricit (ISO/TS 12180-1:2003) Geome
10、trische Produktspezifikation (GPS) - Zylindrizitt - Teil 1: Begriffe und Kenngren der Zylinderform (ISO/TS 12180-1:2003) This Technical Specification (CEN/TS) was approved by CEN on 8 October 2007 for provisional application. The period of validity of this CEN/TS is limited initially to three years.
11、 After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available p
12、romptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgiu
13、m, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR S
14、TANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN ISO/TS 12180-1:2007: E Licensed CopyChinese Un
15、iversity of Hong Kong, 20/10/2008 09:34, Uncontrolled Copy, (c) BSI Foreword The text of ISO/TS 12180-1:2003 has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification” of the International Organization for Standardization (ISO) and has b
16、een taken over as CEN ISO/TS 12180-1:2007 by Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is held by AFNOR. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent ri
17、ghts. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cyp
18、rus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO/T
19、S 12180-1:2003 has been approved by CEN as a CEN ISO/TS 12180-1:2007 without any modification. CEN ISO/TS 12180-1:2007 ii Licensed CopyChinese University of Hong Kong, 20/10/2008 09:34, Uncontrolled Copy, (c) BSI iii Contents Page Forewordiv Introduction v 1 Scope1 2 Normative references .1 3 Terms
20、and definitions.1 3.1 General terms1 3.2 Terms relating to the surface.2 3.3 Terms relating to the reference cylinder 4 3.4 Terms relating to the circumference and the generatrix 5 3.5 Terms relating to the filter function 5 3.6 Parameters.7 4 Radial cross-section deviations10 5 Straightness deviati
21、ons10 Annex A (informative) Mathematical definition of cylindricity tolerances of nominal integral features 11 Annex B (informative) Consideration in the assessment of deviations from cylindrical form 12 Annex C (informative) Synoptic tables of terms, abbreviations and parameters14 Annex D (informat
22、ive) Relation to the GPS matrix model 16 Bibliography .18 CEN ISO/TS 12180-1:2007 Licensed CopyChinese University of Hong Kong, 20/10/2008 09:34, Uncontrolled Copy, (c) BSI iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS
23、O member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, gove
24、rnmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DD CEN ISO2TS 12180 2007
链接地址:https://www.31doc.com/p-3752690.html