DD-CEN-ISO-TS-24534-4-2008.pdf
《DD-CEN-ISO-TS-24534-4-2008.pdf》由会员分享,可在线阅读,更多相关《DD-CEN-ISO-TS-24534-4-2008.pdf(104页珍藏版)》请在三一文库上搜索。
1、DRAFT FOR DEVELOPMENT DD CEN ISO/TS 24534-4:2008 Automatic vehicle and equipment identification Electronic Registration Identification (ERI) for vehicles Part 4: Secure communications using asymmetrical techniques ICS 03.220.20; 35.240.60 ? Licensed CopyChinese University of Hong Kong, 20/10/2008 09
2、:34, Uncontrolled Copy, (c) BSI DD CEN ISO/TS 24534-4:2008 This Draft for Development was published under the authority of the Standards Policy and Strategy Committee on 31 March 2008 BSI 2008 ISBN 978 0 580 54816 1 National foreword This Draft for Development is the UK implementation of CEN ISO/TS
3、24534-4:2008. This publication is not to be regarded as a British Standard. It is being issued in the Draft for Development series of publications and is of a provisional nature. It should be applied on this provisional basis, so that information and experience of its practical application can be ob
4、tained. Comments arising from the use of this Draft for Development are requested so that UK experience can be reported to the European organization responsible for its conversion to a European standard. A review of this publication will be initiated not later than three years after its publication
5、by the European organization so that a decision can be taken on its status. Notification of the start of the review period will be made in an announcement in the appropriate issue of Update Standards. According to the replies received by the end of the review period, the responsible BSI Committee wi
6、ll decide whether to support the conversion into a European Standard, to extend the life of the Technical Specification or to withdraw it. Comments should be sent to the Secretary of the responsible BSI Technical Committee at British Standards House, 389 Chiswick High Road, London W4 4AL. The UK par
7、ticipation in its preparation was entrusted to Technical Committee EPL/278, Road transport informatics. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users ar
8、e responsible for its correct application. Amendments/corrigenda issued since publication DateComments Licensed CopyChinese University of Hong Kong, 20/10/2008 09:34, Uncontrolled Copy, (c) BSI TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN ISO/TS 24534-4 February 2008 I
9、CS 35.240.60; 03.220.20 English Version Automatic vehicle and equipment identification - Electronic Registration Identification (ERI) for vehicles - Part 4: Secure communications using asymmetrical techniques (ISO/TS 24534- 4:2008) Identification automatique des vhicules et des quipements - Identifi
10、cation denregistrement lectronique (ERI) pour les vhicules - Partie 4: Communications sres utilisant des techniques asymtriques (ISO/TS 24534- 4:2008) Straenverkehrstelematik (RTTT) - Automatische Identifizierung von Fahrzeugen und Ausrstungen - Elektronische Identifizierung fr die Registrierung (ER
11、I) - Teil 4: Sichere Anwendungsebene mittels asymmetrischer Techniken (ISO/TS 24534-4:2008) This Technical Specification (CEN/TS) was approved by CEN on 17 July 2006 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of
12、 CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an
13、 appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Repu
14、blic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE
15、 NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN ISO/TS 24534-4:2008: E Licensed CopyChinese University of Hong Kong, 20/10/20
16、08 09:34, Uncontrolled Copy, (c) BSI Foreword This document (CEN ISO/TS 24534-4:2008) has been prepared by Technical Committee CEN/TC 278 “Road transport and traffic telematics“, the secretariat of which is held by NEN, in collaboration with Technical Committee ISO/TC 204 “Transport information and
17、control systems“. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national stan
18、dards organizations of the following countries are bound to announce this CEN Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
19、Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. CEN ISO/TS 24534-4:2008 Licensed CopyChinese University of Hong Kong, 20/10/2008 09:34, Uncontrolled Copy, (c) BSI iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 2 3 Te
20、rms and definitions. 2 4 Abbreviations 11 5 System communications concept. 12 5.1 Introduction. 12 5.2 Overview 12 5.3 Security services 19 5.4 Communication architecture description. 24 5.5 Interfaces. 26 6 Interface requirements. 27 6.1 Overview 27 6.2 Abstract transaction definitions 28 6.3 The E
21、RT interfaces . 65 Annex A (normative) ASN.1 Modules. 69 Annex B (informative) Operational scenarios . 80 Annex C (normative) PICS pro forma. 91 Bibliography. 95 CEN ISO/TS 24534-4:2008 Licensed CopyChinese University of Hong Kong, 20/10/2008 09:34, Uncontrolled Copy, (c) BSI iv Foreword ISO (the In
22、ternational Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee h
23、as been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical
24、 standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodi
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DD CEN ISO TS 24534 2008
链接地址:https://www.31doc.com/p-3752697.html