DEP 39.01.20.10-Gen.pdf
《DEP 39.01.20.10-Gen.pdf》由会员分享,可在线阅读,更多相关《DEP 39.01.20.10-Gen.pdf(47页珍藏版)》请在三一文库上搜索。
1、TECHNICAL SPECIFICATION L80 13%Cr CASING AND TUBING (AMENDMENTS/SUPPLEMENTS TO ISO/DIS 11960.2) DEP 39.01.20.10-Gen. October 1995 DESIGN AND ENGINEERING PRACTICE This document is confidential. Neither the whole nor any part of this document may be disclosed to any third party without the prior writt
2、en consent of Shell International Oil Products B.V. and Shell International Exploration and Production B.V., The Hague, The Netherlands. The copyright of this document is vested in these companies. All rights reserved. Neither the whole nor any part of this document may be reproduced, stored in any
3、retrieval system or transmitted in any form or by any means (electronic, mechanical, reprographic, recording or otherwise) without the prior written consent of the copyright owners. PDF created with pdfFactory Pro trial version PREFACE DEP (Design and Engineering Practice) publications reflect the
4、views, at the time of publication, of: Shell International Oil Products B.V. (SIOP) and Shell International Exploration and Production B.V. (SIEP) and Shell International Chemicals B.V. (SIC) The Hague, The Netherlands, and other Service Companies. They are based on the experience acquired during th
5、eir involvementwith the design, construction, operation and maintenance of processing units and facilities, and they are supplemented with the experience of Group Operating companies. Where appropriate they are based on, or reference is made to, national and international standards and codes of prac
6、tice. The objective is to set the recommendedstandard for good design and engineeringpractice applied by Group companies operating an oil refinery, gas handling installation, chemical plant, oil and gas production facility, or any other such facility, and thereby to achieve maximum technical and eco
7、nomic benefit from standardization. The information set forth in these publications is provided to users for their consideration and decision to implement. This is of particular importance where DEPs may not cover every requirement or diversity of condition at each locality. The system of DEPs is ex
8、pected to be sufficiently flexible to allow individual operating companies to adapt the information set forth in DEPs to their own environment and requirements. When Contractors or Manufacturers/Suppliers use DEPs they shall be solely responsible for the quality of work and the attainment of the req
9、uired design and engineering standards. In particular, for those requirements not specifically covered, the Principal will expect them to follow those design and engineering practices which will achieve the same level of integrity as reflected in the DEPs. If in doubt, the Contractor or Manufacturer
10、/Supplier shall, without detracting from his own responsibility, consult the Principal or its technical advisor. The right to use DEPs is granted by SIOP, SIEP or SIC, in most cases under Service Agreements primarily with companies of the Royal Dutch/Shell Group and other companies receiving technic
11、al advice and services from SIOP, SIEP or SIC. Consequently, three categories of users of DEPs can be distinguished: 1)Operating companies having a Service Agreement with SIOP, SIEP, SIC or other Service Company. The use of DEPs by these Operating companies is subject in all respects to the terms an
12、d conditions of the relevant Service Agreement. 2)Other parties who are authorized to use DEPs subject to appropriate contractual arrangements. 3)Contractors/subcontractors and Manufacturers/Suppliers under a contract with users referred to under 1) or 2) which requires that tenders for projects, ma
13、terials supplied or - generally - work performed on behalf of the said users comply with the relevant standards. Subject to any particular terms and conditions as may be set forth in specific agreements with users, SIOP, SIEP and SIC disclaim any liability of whatsoever nature for any damage (includ
14、ing injury or death) suffered by any company or person whomsoever as a result of or in connection with the use, application or implementation of any DEP, combination of DEPs or any part thereof. The benefit of this disclaimer shall inure in all respects to SIOP, SIEP, SIC and/or any company affiliat
15、ed to these companies that may issue DEPs or require the use of DEPs. Without prejudice to any specific terms in respect of confidentiality under relevant contractual arrangements, DEPs shall not, without the prior written consent of SIOP and SIEP, be disclosed by users to any company or person whom
16、soever and the DEPs shall be used exclusively for the purpose for which they have been provided to the user. They shall be returned after use, including any copies which shall only be made by users with the express prior written consent of SIOP and SIEP. The copyright of DEPs vests in SIOP and SIEP.
17、 Users shall arrange for DEPs to be held in safe custody and SIOP or SIEP may at any time require information satisfactory to them in order to ascertain how users implement this requirement. All administrative queries should be directed to the DEP Administrator in SIOP. NOTE: In addition to DEP publ
18、ications there are Standard Specifications and Draft DEPs for Development (DDDs). DDDs generally introduce new procedures or techniques that will probably need updating as further experience develops during their use. The above requirements for distribution and use of DEPs are also applicable to Sta
19、ndard Specifications and DDDs. Standard Specifications and DDDs will gradually be replaced by DEPs. DEP 39.01.20.10-Gen. October 1995 Page 2 PDF created with pdfFactory Pro trial version TABLE OF CONTENTS PART IINTRODUCTION .5 1.1SCOPE 5 1.2DISTRIBUTION, INTENDED USE AND REGULATORY CONSIDERATIONS5
20、1.3DEFINITIONS 5 1.4ABBREVIATIONS 6 1.5CROSS-REFERENCES 6 1.6GUIDANCE FOR USE.6 PART IIAMENDMENTS/SUPPLEMENTS TO ISO/DIS 11960.2 . 7 SECTION 1 SCOPE 8 SECTION 2 NORMATIVE REFERENCES8 SECTION 5 PROCESS OF MANUFACTURE 8 5.1GENERAL8 5.2HEAT TREATMENT 8 5.3STRAIGHTENING .9 5.4TRACEABILITY .9 SECTION 6 M
21、ATERIAL REQUIREMENTS 9 6.1CHEMICAL REQUIREMENTS 9 6.2MECHANICAL PROPERTIES REQUIREMENTS .10 6.3SURFACE CONDITION.11 SECTION 7 DIMENSIONS, MASSES, TOLERANCES AND PIPE ENDS 12 7.6CASING JOINTERS 12 7.7HEIGHT AND TRIM OF ELECTRIC WELD FLASH 12 7.11PIPE ENDS12 7.12COUPLING MAKE-UP AND THREAD PROTECTION
22、12 SECTION 8 COUPLINGS .13 8.1MATERIAL.13 8.2PROCESS OF MANUFACTURE.13 8.3PERFORMANCE PROPERTIES .13 8.5DIMENSIONS AND TOLERANCES 13 8.9REDUCING COUPLINGS14 8.13SURFACE INSPECTION .14 8.15REPAIR AND REMOVAL OF IMPERFECTIONS AND DEFECTS 14 8.16THREAD PLATING - GROUP 4 14 8.17COUPLINGS AND COUPLING BL
23、ANK PROTECTION - GROUP 4. 14 8.18ANTI-GALLING TREATMENT.14 SECTION 9 INSPECTION AND TESTING14 9.1GENERAL14 9.2TESTING OF CHEMICAL COMPOSITION .15 9.3TESTING OF MECHANICAL AND TECHNOLOGICAL PROPERTIES. 16 9.4HYDROSTATIC TEST.18 9.7NON-DESTRUCTIVE INSPECTION .19 9.8TEST METHODS AND RESULTS.22 9.10RETE
24、STS 23 9.11IN-PROCESS HARDNESS TESTING .25 SECTION 10MARKING25 10.2COUPLINGS AND CONNECTORS.25 10.3PIPE AND PUP-JOINTS25 10.4DIE STAMP MARKING REQUIREMENTS 26 10.6PAINT STENCIL MARKING 26 DEP 39.01.20.10-Gen. October 1995 Page 3 PDF created with pdfFactory Pro trial version 10.8THREAD MARKING - ALL
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DEP 39.01.20.10-Gen 39.01 20.10 Gen
链接地址:https://www.31doc.com/p-3753908.html