DEP 33.66.05.31-Gen.pdf
《DEP 33.66.05.31-Gen.pdf》由会员分享,可在线阅读,更多相关《DEP 33.66.05.31-Gen.pdf(55页珍藏版)》请在三一文库上搜索。
1、TECHNICAL SPECIFICATION ELECTRICAL MACHINES - CAGE-INDUCTION TYPES (AMENDMENTS/SUPPLEMENTS TO IEC 60034-1) DEP 33.66.05.31-Gen. January 1999 DESIGN AND ENGINEERING PRACTICE This document is confidential. Neither the whole nor any part of this document may be disclosed to any third party without the
2、prior written consent of Shell International Oil Products B.V. and Shell International Exploration and Production B.V., The Hague, The Netherlands. The copyright of this document is vested in these companies. All rights reserved. Neither the whole nor any part of this document may be reproduced, sto
3、red in any retrieval system or transmitted in any form or by any PDF created with pdfFactory Pro trial version means (electronic, mechanical, reprographic, recording or otherwise) without the prior written consent of the copyright owners. PDF created with pdfFactory Pro trial version PREFACE DEP (
4、Design and Engineering Practice) publications reflect the views, at the time of publication, of: Shell International Oil Products B.V. (SIOP) and Shell International Exploration and Production B.V. (SIEP) and Shell International Chemicals B.V. (SIC) The Hague, The Netherlands, and other Service Comp
5、anies. They are based on the experience acquired during their involvementwith the design, construction, operation and maintenance of processing units and facilities, and they are supplemented with the experience of Group Operating companies. Where appropriate they are based on, or reference is made
6、to, national and international standards and codes of practice. The objective is to set the recommendedstandard for good design and engineeringpractice applied by Group companies operating an oil refinery, gas handling installation, chemical plant, oil and gas production facility, or any other such
7、facility, and thereby to achieve maximum technical and economic benefit from standardization. The information set forth in these publications is provided to users for their consideration and decision to implement. This is of particular importance where DEPs may not cover every requirement or diversi
8、ty of condition at each locality. The system of DEPs is expected to be sufficiently flexible to allow individual operating companies to adapt the information set forth in DEPs to their own environment and requirements. When Contractors or Manufacturers/Suppliers use DEPs they shall be solely respons
9、ible for the quality of work and the attainment of the required design and engineering standards. In particular, for those requirements not specifically covered, the Principal will expect them to follow those design and engineering practices which will achieve the same level of integrity as reflecte
10、d in the DEPs. If in doubt, the Contractor or Manufacturer/Supplier shall, without detracting from his own responsibility, consult the Principal or its technical advisor. The right to use DEPs is granted by SIOP, SIEP or SIC, in most cases under Service Agreements primarily with companies of the Roy
11、al Dutch/Shell Group and other companies receiving technical advice and services from SIOP, SIEP or SIC. Consequently, three categories of users of DEPs can be distinguished: 1)Operating companies having a Service Agreement with SIOP, SIEP, SIC or other Service Company. The use of DEPs by these Oper
12、ating companies is subject in all respects to the terms and conditions of the relevant Service Agreement. 2)Other parties who are authorized to use DEPs subject to appropriate contractual arrangements. 3)Contractors/subcontractors and Manufacturers/Suppliers under a contract with users referred to u
13、nder 1) or 2) which requires that tenders for projects, materials supplied or - generally - work performed on behalf of the said users comply with the relevant standards. Subject to any particular terms and conditions as may be set forth in specific agreements with users, SIOP, SIEP and SIC disclaim
14、 any liability of whatsoever nature for any damage (including injury or death) suffered by any company or person whomsoever as a result of or in connection with the use, application or implementation of any DEP, combination of DEPs or any part thereof. The benefit of this disclaimer shall inure in a
15、ll respects to SIOP, SIEP, SIC and/or any company affiliated to these companies that may issue DEPs or require the use of DEPs. Without prejudice to any specific terms in respect of confidentiality under relevant contractual arrangements, DEPs shall not, without the prior written consent of SIOP and
16、 SIEP, be disclosed by users to any company or person whomsoever and the DEPs shall be used exclusively for the purpose for which they have been provided to the user. They shall be returned after use, including any copies which shall only be made by users with the express prior written consent of SI
17、OP and SIEP. The copyright of DEPs vests in SIOP and SIEP. Users shall arrange for DEPs to be held in safe custody and SIOP or SIEP may at any time require information satisfactory to them in order to ascertain how users implement this requirement. All administrative queries should be directed to th
18、e DEP Administrator in SIOP. NOTE: In addition to DEP publications there are Standard Specifications and Draft DEPs for Development (DDDs). DDDs generally introduce new procedures or techniques that will probably need updating as further experience develops during their use. The above requirements f
19、or distribution and use of DEPs are also applicable to Standard Specifications and DDDs. Standard Specifications and DDDs will gradually be replaced by DEPs. DEP 33.66.05.31-Gen. January 1999 Page 2 PDF created with pdfFactory Pro trial version TABLE OF CONTENTS PART IINTRODUCTION .4 1.1SCOPE 4 1.2
20、DISTRIBUTION, INTENDED USE AND REGULATORY CONSIDERATIONS4 1.3DEFINITIONS 5 1.4CROSS-REFERENCES 5 PART IIGENERAL .6 2.1STATEMENT OF COMPLIANCE 6 2.2LIFETIME AND RELIABILITY 6 2.3EFFICIENCY AND LIFE-CYCLE COST 6 2.4GENERAL FEATURES OF DESIGN .7 PART IIIAMENDMENTS/SUPPLEMENTS TO IEC 60034-1 8 Section 2
21、Definitions 9 Section 3Duty .12 Section 4Rating 13 Section 5Site operating conditions .14 Section 6Electrical operating conditions .15 Section 7Thermal performance and tests.16 Section 8Other performance and tests .17 Section 9Rating plates22 Section 10Miscellaneous requirements 24 Section 12Additio
22、nal requirements for machines in hazardous areas 35 Section 13Inspection and tests.37 Section 14Documentation.41 PART IIIAMENDMENTS AND SUPPLEMENTS TO IEC 60034-14 42 Section 1Scope and object.42 Section 8Limits of bearing housing vibration 42 Section 9Limits of relative shaft vibration42 Section 10
23、Vibration tests43 PART IVREFERENCES 44 APPENDICES ANNEX CINSULATION QUALITY TEST47 ANNEX DMINIMUM EXPECTED FULL LOAD EFFICIENCY OF MACHINES. 49 ANNEX EMINIMUM EXPECTED FULL LOAD POWER FACTOR OF MACHINES 51 ANNEX FEXAMPLE OF ALL-IN COST CALCULATION 52 DEP 33.66.05.31-Gen. January 1999 Page 3 PDF crea
24、ted with pdfFactory Pro trial version PART IINTRODUCTION 1.1SCOPE This DEP specifies requirements and gives recommendations for electrical machines of the cage-induction type. It applies to both induction motors and induction generators. This DEP is a revision of the DEP of the same number dated No
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DEP 33.66.05.31-Gen 33.66 05.31 Gen
链接地址:https://www.31doc.com/p-3754098.html