BS-ISO-15014-2007.pdf
《BS-ISO-15014-2007.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-15014-2007.pdf(20页珍藏版)》请在三一文库上搜索。
1、BS ISO 15014:2007 ICS 83.140.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Plastics Extruded sheets of poly(vinylidene fluoride) (PVDF) Requirements and test methods Licensed CopyChinese University of Hong Kong, 11/04/2009 09:18, Uncontrolled Copy, (c) BS
2、I This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2009 BSI 2009 ISBN 978 0 580 56392 8 Amendments/corrigenda issued since publication DateComments BS ISO 15014:2007 National foreword This British Standard is the UK implementation
3、of ISO 15014:2007. The UK participation in its preparation was entrusted to Technical Committee PRI/76, Laminated sheet for decorative purposes. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the nec
4、essary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Licensed CopyChinese University of Hong Kong, 11/04/2009 09:18, Uncontrolled Copy, (c) BSI BS ISO 15014:2007 Reference number ISO 1501
5、4:2007(E) ISO 2007 INTERNATIONAL STANDARD ISO 15014 First edition 2007-10-01 Plastics Extruded sheets of poly(vinylidene fluoride) (PVDF) Requirements and test methods Plastiques Plaques extrudes en poly(fluorure de vinylidne) (PVDF) Exigences et mthodes dessai Licensed CopyChinese University of Hon
6、g Kong, 11/04/2009 09:18, Uncontrolled Copy, (c) BSI BS ISO 15014:2007 ISO 15014:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are lic
7、ensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of
8、the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating
9、 to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photoco
10、pying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switze
11、rland ii ISO 2007 All rights reserved Licensed CopyChinese University of Hong Kong, 11/04/2009 09:18, Uncontrolled Copy, (c) BSI BS ISO 15014:2007 ISO 15014:2007(E) ISO 2007 All rights reserved iii Contents Page Foreword iv 1 Scope 1 2 Normative references1 3 Material .1 4 Requirements.2 4.1 Appeara
12、nce 2 4.2 Dimensional tolerances 2 4.3 Properties .3 5 Test methods4 5.1 Test specimens4 5.2 Delivery condition4 5.3 Appearance 5 5.4 Dimensions.5 5.5 Tensile stress at yield, y, and tensile strain at break, B5 5.6 Modulus of elasticity in tension, Et5 5.7 Charpy impact strength of notched specimens
13、, acn5 5.8 Melt mass-flow rate (MFR)5 5.9 Determination of shrinkage on heating.6 6 Designation 7 6.1 Example for sheets7 6.2 Example for sheets in rolled form8 7 Marking.8 Annex A (normative) Requirements for rectangularity.9 Licensed CopyChinese University of Hong Kong, 11/04/2009 09:18, Uncontrol
14、led Copy, (c) BSI BS ISO 15014:2007 ISO 15014:2007(E) iv ISO 2007 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out th
15、rough ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collab
16、orates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Stan
17、dards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of
18、 this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15014 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products, in collaboration with Technical Committee CEN/TC 249, Plastics, of the
19、 European Committee for Standardization (CEN). Licensed CopyChinese University of Hong Kong, 11/04/2009 09:18, Uncontrolled Copy, (c) BSI BS ISO 15014:2007 INTERNATIONAL STANDARD ISO 15014:2007(E) ISO 2007 All rights reserved 1 Plastics Extruded sheets of poly(vinylidene fluoride) (PVDF) Requirement
20、s and test methods 1 Scope This International Standard specifies the requirements and test methods for solid flat extruded sheets of poly(vinylidene fluoride) homopolymers and poly(vinylidene fluoride) copolymers without fillers or reinforcing materials. This International Standard also applies to P
21、VDF sheet in rolled form. It applies only to thicknesses from 1 mm to 15 mm. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the refer
22、enced document (including any amendments) applies. ISO 179-1, Plastics Determination of Charpy impact properties Part 1: Non-instrumented impact test ISO 179-2, Plastics Determination of Charpy impact properties Part 2: Instrumented impact test ISO 291, Plastics Standard atmospheres for conditioning
23、 and testing ISO 527-2, Plastics Determination of tensile properties Part 2: Test conditions for moulding and extrusion plastics ISO 1133, Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics ISO 2818, Plastics Preparation of test specimens by
24、 machining ISO 9080, Plastics piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation ISO 11501, Plastics Film and sheeting Determination of dimensional change on heating ISO 12086-1, Plastics Fluoropolymer dispersions
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS ISO 15014 2007
链接地址:https://www.31doc.com/p-3754987.html