ECA-EIA-364-09C-1999-R2006.pdf
《ECA-EIA-364-09C-1999-R2006.pdf》由会员分享,可在线阅读,更多相关《ECA-EIA-364-09C-1999-R2006.pdf(16页珍藏版)》请在三一文库上搜索。
1、EIA STANDARD ANSIIEIA-364-09C-1999 (R2006) Approved: April 23,1999 Reaffirmed: March 27,2006 TP-09C Durability Test Procedure for Electrical Connectors and Contacts EIA-3 64-09C (Revision of EIA-364-09B) JUNE 1999 ELECTRONIC INDUSTRIES ALLIANCE Electronic Components, Assemblies, Equipment securing o
2、f test fixture shaii not affect seif-agnment. Mer mounting, fbliy mate and unmate for the number of cycles specied in the referencing document. 4.2 Cycle rate Unless otherwise specied in the referencing document, the cycle rate per hour sha be: - Automatic equipment: 500 f 50 -Manual rnating/unmatin
3、g: 300 maximum - Automatic, Circular Connectors: 250 to 300 EIA-3 64-09C Page 3 4.3 Electrical load No electrical load shall be applied to the specimens during the test, unless otherwise specified. 4.4 Inspection or test At the intervals specified in the referencing document, inspections or tests ma
4、y be performed. CAUTION - DisWmg the specimens for intermediate inspection or measurements could a;8ect subsequent results. 4.5 Measurements 4.5.1 Mating and unmathg forces, contact resistance, shell resistance, insulation resistance, dielectric withstanding voltage, contact retention, and sealing t
5、ests are examples of measurements that may be made prior to, during or after testing and that would show the effects of durability. 4.5.2 The connectors or contacts shall be examined to determine the effects of durabiiity cycling that would include the following: 4.5.2.1 W e a r on coupling device.
6、4.5.2.2 Loose or worn rivets; where applicable. 4.5.2.3 Uneven wear, galling, removal of plating on contacts and shells. 4.5.2.4 Free metal chips on face of inserts. 4.5.2.5 Displaced, bent or broken contacts. 4.5.2.6 Inability to properly mate and unmate. 4.5.2.7 Pierced resilient inserts and broke
7、n or chipped hard dielectrics. 4.5.2.8 Mechanical operational characteristics, including effectiveness of keys and polarizing systems. EU-364-09C Page 4 5 Details to be specified The following details shall be specified in the referencing document: 5.1 Number of cycles 5.2 Lubrication, if other than
8、 as specified 5.3 Observations or m e a s u r e m e n t s to be made before, during and after cycling 5.4 Cycling rate, if other than as spec%ed in 4.2 5.5 M a n u a l or automatic cycling 5.6 Periodic inspection, if required 5.7 Number of specimens to be tested 5.8 Whether or not coupling devices a
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ECA EIA 364 09 1999 R2006
链接地址:https://www.31doc.com/p-3755563.html