《EN-300-476-7-V1.2.1-2000.pdf》由会员分享,可在线阅读,更多相关《EN-300-476-7-V1.2.1-2000.pdf(19页珍藏版)》请在三一文库上搜索。
1、ETSI EN 300 476-7V1.2.1(2000-11) European Standard (Telecommunications series) Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 7: Physical layer ETSI ETSI EN 300 476-7 V1.2.1 (2000-11)2 Reference REN/DECT
2、-040106-7 Keywords access, DECT, PICS, radio, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important n
3、otice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Porta
4、ble Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information
5、 on the current status of this and other ETSI documents is available at http:/www.etsi.org/tb/status/ If you find errors in the present document, send your comment to: editoretsi.fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the for
6、egoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2000. All rights reserved. ETSI ETSI EN 300 476-7 V1.2.1 (2000-11)3 Contents Intellectual Property Rights 4 Foreword4 1Scope5 2References5 3Definitions and abbreviations5 3.1Definitions 5 3.2Abbre
7、viations 6 4Conformance requirement concerning PICS6 Annex A (normative):Physical (PHY) layer PICS proforma .7 A.1Introduction for completing the PICS proforma.7 A.1.1Purposes and structure. 7 A.1.2Instruction for completing the PICS. 8 A.2Identification of the implementation9 A.2.1Date of statement
8、. 9 A.2.2Implementation Under Test (IUT) identification 9 A.2.3System Under Test (SUT) identification 9 A.2.4Product supplier 9 A.2.5Client 10 A.2.6Contact person 10 A.3Identification of the protocol.11 A.3.1Defect report numbers and amendments implemented 11 A.3.2Addenda implemented. 11 A.4Global s
9、tatement of conformance11 A.5Capabilities.12 A.5.1Major capabilities 12 A.5.1.1Services. 12 A.5.1.2Procedures. 13 A.5.1.2.1Physical layer procedures 13 A.5.1.2.2Management entity procedures 13 A.5.2Protocol Data Units. 13 A.5.3Receiver/Transmitter characteristics 16 A.5.3.1Transmitter characteristic
10、s 16 A.5.3.2Receiver characteristics 17 Bibliography.18 History.19 ETSI ETSI EN 300 476-7 V1.2.1 (2000-11)4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publ
11、icly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI
12、 Web server (http:/www.etsi.org/ipr). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, o
13、r may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Project Digital Enhanced Cordless Telecommunications (DECT). The present document is part 7 of a multi-part deliverable covering the Digital Enhanced Cordless Teleco
14、mmunications (DECT); Common Interface (CI); Protocol Implementation Conformance Statement (PICS) proforma, as identified below: Part 1:“Network (NWK) layer - Portable radio Termination (PT)“; Part 2:“Data Link Control (DLC) layer - Portable radio Termination (PT)“; Part 3:“Medium Access Control (MAC
15、) layer - Portable radio Termination (PT)“; Part 4:“Network (NWK) layer - Fixed radio Termination (FT)“; Part 5:“Data Link Control (DLC) layer - Fixed radio Termination (FT)“; Part 6:“Medium Access Control (MAC) layer - Fixed radio Termination (FT)“; Part 7:“Physical layer“. Annex A contains the PIC
16、S proforma for the physical layer. National transposition dates Date of adoption of this EN:24 November 2000 Date of latest announcement of this EN (doa):28 February 2001 Date of latest publication of new National Standard or endorsement of this EN (dop/e):31 August 2001 Date of withdrawal of any co
17、nflicting National Standard (dow):31 August 2001 ETSI ETSI EN 300 476-7 V1.2.1 (2000-11)5 1Scope The present document provides the Protocol Implementation Conformance Statement (PICS) proforma for the Digital Enhanced Cordless Telecommunications Network layer at the Portable Termination as defined i
18、n EN 300 175-2 2 in compliance with the relevant requirements and in accordance with the relevant guidance given in ISO/IEC 9646-7 4. The supplier of an implementation which is claimed to conform to EN 300 175-2 2 is required to complete a copy of the PICS proforma provided in the annex A of the pre
19、sent document. 2References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific referen
20、ce, subsequent revisions do not apply. For a non-specific reference, the latest version applies. A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the same number. 1ETSI EN 300 175-1: “Digital Enhanced Cordless Telecommunications (DECT); Common
21、 Interface (CI); Part 1: Overview“. 2ETSI EN 300 175-2: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 2: Physical Layer (PHL)“. 3ISO/IEC 9646-1 (1995): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1:
22、 General concepts“. 4ISO/IEC 9646-7 (1995): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 3Definitions and abbreviations 3.1Definitions For the purposes of the present document, the following t
23、erms and definitions apply: -terms given in EN 300 175-1 1; -terms given in ISO/IEC 9646-1 3 and in ISO/IEC 9646-7 4. In particular, the following terms given in ISO/IEC 9646-1 3 apply: Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system claimed
24、to conform to a given specification, stating which capabilities have been implemented. The ICS can take several forms: protocol ICS, profile ICS, profile specific ICS, information object ICS, etc. ICS proforma: document, in the form of a questionnaire, which when completed for an implementation or s
25、ystem becomes an ICS Protocol ICS (PICS): PICS for an implementation or system claimed to conform to a given protocol specification ETSI ETSI EN 300 476-7 V1.2.1 (2000-11)6 The following definition also applies: DECT Common Interface ICS: ICS for an implementation or system claimed to conform to a g
26、iven DECT Common Interface specification 3.2Abbreviations For the purposes of the present document, the abbreviations given in ISO/IEC 9646-1 3, the Physical layer abbreviations given in EN 300 175-2 2, and the following apply: ICSImplementation Conformance Statement IUTImplementation Under Test len
27、_blength specified as BITSTRING PICSProtocol Implementation Conformance Statement Sp.support(ed) SUTSystem Under Test valvalue (of the field) 4Conformance requirement concerning PICS If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be tech
28、nically equivalent to the text of the PICS proforma given in annex A, and shall preserve the numbering/naming and ordering of the proforma items. An ICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with the instructions for completion given in cl
29、ause A.1. ETSI ETSI EN 300 476-7 V1.2.1 (2000-11)7 Annex A (normative): Physical (PHY) layer PICS proforma Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the PICS proforma in this
30、 annex so that it can be used for its intended purposes and may further publish the completed PICS. A.1Introduction for completing the PICS proforma A.1.1Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the portable termina
31、tion specific data link control layer requirements of EN 300 175-2 2: DECT PH layer may provide information about the implementation in a standardized manner. The PICS proforma is subdivided into subclauses for the following categories of information: -instructions for completing the PICS proforma;
32、-identification of the implementation; -identification of the EN 300 175-2: DECT PH layer; -PICS proforma tables: -global statement of conformance; -functional groups and procedures; -timers and protocol parameters; -messages; -information elements; -negotiation capabilities; -protocol error handlin
33、g; -multilayer dependencies. The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7. Item column The item column contains a number which identifies the item in the table. Item description column The item des
34、cription column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“. Status column The following notations, defined in ISO/IEC 9646-7, are used for the status column: m or Mmandatory - the capability is required to be
35、 supported. o or Ooptional - the capability may be supported or not. ETSI ETSI EN 300 476-7 V1.2.1 (2000-11)8 n/a or N/Anot applicable - in the given context, it is impossible to use the capability. x or Xprohibited (excluded) - there is a requirement not to use this capability in the given context.
36、 o.i or O.iqualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies an unique group of related optional items and the logic of their selection which is defined immediately following the table. ci or Ciconditional - therequirement on the capabil
37、ity (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying an unique conditional status expression which is defined immediately following the table. i or Iout-of-scope - this capability is outside the scope of the given specification, an
38、d hence irrelevant and not subject to conformance testing. This status is in particular applicable for data fields which are reserved for future use. The structure of such fields has to be supported, but the value is undefined and thus to be ignored. Reference column The reference column gives refer
39、ence to EN 300 175-2: PHY layer, except where explicitly stated otherwise. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7, are used for the support column: Y or ysupported by the implementation N o
40、r nnot supported by the implementation N/A, n/a or -no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional status) In each context, the kind of “non-support“ which is implemented at the receipt may be additionally indicated such as: -Errthe item is treat
41、ed as a protocol error; -lgthe item is received and ignored (i.e. processed syntactically, but not semantically); -rjthe item is received and rejected. NOTE:As stated in ISO/IEC 9646-7, support for a PDU requires the ability to parse all valid parameters of that PDU. Supporting a PDU while having no
42、 ability to parse a valid parameter is non-conformant. Support for a parameter on a PDU means that the semantics of that parameter are supported. Values allowed column The values allowed column contains the values or the ranges of values allowed. Values supported column The values supported column s
43、hall be filled in by the supplier of the implementation. In this column, the values or the ranges of values supported by the implementation shall be indicated. When the length of a field or group of octets has been specified a specific notation has been used as “len_b“ with meaning length specified
44、as BITSTRING. Prerequisite line A prerequisite line takes the form: Prerequisite: . A prerequisite line before a clause or table title indicates that the whole clause or the whole table is not required to be completed if the predicate is FALSE. A.1.2Instruction for completing the PICS The supplier o
45、f the implementation shall complete the PICS proforma in each of the spaces provided using the notation described in subclause A.1.1 Specific instruction is provided (when necessary) in the text which precedes each table. ETSI ETSI EN 300 476-7 V1.2.1 (2000-11)9 A.2Identification of the implementati
46、on A.2.1Date of statement Identification of the Implementation Under Test (IUT) and the system in which it resides (the System Under Test (SUT) should be filled in so as to provide as much detail as possible regarding version numbers and configuration options. Table A.1: Date of statement Date of st
47、atement DayMonthYear A.2.2Implementation Under Test (IUT) identification The supplier of the implementation shall enter information necessary to uniquely identify the IUT in table A.2. Table A.2: IUT identification IUT identification IUT name IUT version A.2.3System Under Test (SUT) identification T
48、he supplier of the implementation shall enter information necessary to uniquely identify the SUT in table A.3. Table A.3: SUT identification SUT identification SUT nameInternational Portable Equipment Identity (IPEI): Hardware configuration A.2.4Product supplier Table A.4: Product supplier Product s
49、upplier Name Address Phone No. Fax No. E-mail address Additional information ETSI ETSI EN 300 476-7 V1.2.1 (2000-11)10 A.2.5Client The product supplier information and client information should both be filled in if they are different. Table A.5: Client Client Name Address Phone No. Fax No. E-mail address Additional information A.2.6Contact person A person who can answer queries regarding information supplied in the PICS should be named as the contact person. Table A.6: Contact person Contact person Name Address Phone No. Fax No. E-mail address
链接地址:https://www.31doc.com/p-3755932.html