ECA-EIA-ECA-364-10E-2008.pdf
《ECA-EIA-ECA-364-10E-2008.pdf》由会员分享,可在线阅读,更多相关《ECA-EIA-ECA-364-10E-2008.pdf(18页珍藏版)》请在三一文库上搜索。
1、 ANSI/EIA-364-10E-2008 Approved: February 28, 2008 EIA STANDARD TP-10E FLUID IMMERSION TEST PROCEDURE FOR ELECTRICAL CONNECTORS (Revision of EIA-364-10D) EIA/ECA-364-10E EIA/ECA-364-10E FEBRUARY 2008 THE ELECTRONIC COMPONENTS SECTOR OF THE ELECTRONIC INDUSTRIES ALLIANCE Copyright Electronic Componen
2、ts, Assemblies see EIA-364-13 4.2 Preheat each test fluid until it has stabilized at the temperature specified; see table 1 or the referencing document 4.3 The test cycle shall be as specified for each test fluid; see table 1 or the referencing document. 4.4 Transition time between steady state cond
3、itions shall be two minutes maximum and steady state conditions shall be maintained at the specified time with a tolerance of + one minute unless otherwise specified in the referencing document. 4.5 Fluid shall be drained from all recesses by gravity. 4.6 Connectors shall be placed in an air-circula
4、ting oven for the time specified in table 1. Repeat number of cycles specified. 4.7 Remove the specimens and allow them to stabilize at room temperature for a minimum of 1 hour. 4.8 The final torques or forces required to mate and unmate each connector or connector assembly shall be measured and rec
5、orded, if the referencing document test schedule includes mating and unmating measurements after the immersion test; see EIA-364-13. 4.9 Connectors shall be visually examined with the unaided eye for evidence of degradation. Examples of visible degradation from this test may be: 4.9.1 Swelling, crac
6、king or pitting of any resilient material. 4.9.2 Loss of seal or adhesive bonding between two bonded surfaces. 4.9.3 Discoloration of materials, finishes and marking, but this may not be considered detrimental. 4.9.4 Softening of any materials. Copyright Electronic Components, Assemblies see table 1
7、 5.4 Other fluids, not listed in table 1, shall be specified along with their test conditions 5.4 Type of wire insulation if other than TFE 5.5 Test cycle duration and temperature of fluid, if other than as specified in table 1 5.6 Torque or force measurements to mate and unmate, if applicable 6 Doc
8、umentation Documentation shall contain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Specimen description and identification, including fixture if applicable 6.3 Test equipment used, and date of last and next calibration 6.4 Test fluids used 6.5 Tes
9、t condition number or test cycle duration and temperature of fluid if other than specified in table 1. 6.6 Visual observations, measurements and results arranged in a “before“ and “after“ style preferably using one sheet for each connector assembly. 6.7 Name of operator and start/finish date of test
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ECA EIA 364 10 2008
链接地址:https://www.31doc.com/p-3755971.html