ETSI EN-300-019-2-4-V2.2.2-2003.pdf
《ETSI EN-300-019-2-4-V2.2.2-2003.pdf》由会员分享,可在线阅读,更多相关《ETSI EN-300-019-2-4-V2.2.2-2003.pdf(21页珍藏版)》请在三一文库上搜索。
1、 ETSI EN 300 019-2-4 V2.2.2 (2003-04) European Standard (Telecommunications series) Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-4: Specification of environmental tests; Stationary use at non-weatherprotected locations ETSI
2、 ETSI EN 300 019-2-4 V2.2.2 (2003-04) 2 Reference REN/EE-01032-2-42 Keywords environment, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-P
3、rfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such
4、 versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject
5、 to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be reproduced except as
6、authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and
7、 the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI EN 300 019-2-4 V2.2.2 (2003-04) 3 Contents Intellectual Property Rights4 For
8、eword.4 1 Scope5 2 References5 3 Environmental test specifications.5 3.1 Specification T 4.1: Non-weatherprotected locations, climatic tests6 3.2 Specification T 4.1E: Non-weatherprotected locations - extended, climatic tests8 3.3 Specification T 4.2L: Non-weatherprotected locations extremely cold,
9、climatic tests10 3.4 Specification T 4.2H: Non-weatherprotected locations extremely warm dry, climatic tests.12 3.5 Specification T 4.1, 4.1E, 4.2L and 4.2H: Non-weatherprotected locations - mechanical tests.14 4 Earthquake test specification15 4.1 Vibration response investigation15 4.2 Test conditi
10、oning15 5 Notes to tables17 5.1 General note .17 5.2 Notes to tables 1 to 618 Annex A (informative): Bibliography.20 History21 ETSI ETSI EN 300 019-2-4 V2.2.2 (2003-04) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The
11、information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from
12、 the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). All published ETSI deliverables shall include information which directs the reader to the above source of information. Foreword This European Standard (Telecommunications series) has been
13、 produced by ETSI Technical Committee Environmental Engineering (EE). The present document is part 2, sub-part 4 of a multi-part deliverable covering the classification of environmental conditions and environmental tests for telecommunications equipment, as identified below: Part 1: “Classification
14、of environmental conditions“; (see note 1) Part 2: “Specification of environmental tests“; (see note 2) Sub-part 0: “Introduction“; Sub-part 1: “Storage“; Sub-part 2: “Transportation“; Sub-part 3: “Stationary use at weatherprotected locations“; Sub-part 4: “Stationary use at non-weatherprotected loc
15、ations“; Sub-part 5: “Ground vehicle installations“; Sub-part 6: “Ship environments“; Sub-part 7: “Portable and non-stationary use“; Sub-part 8: “Stationary use at underground locations“. NOTE 1: Specifies different standardized environmental classes covering climatic and biological conditions, chem
16、ically and mechanically active substances and mechanical conditions during storage, transportation and in use. NOTE 2: Specifies the recommended test severities and test methods for the different environmental classes. National transposition dates Date of latest announcement of this EN (doa): 31 Jul
17、y 2003 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 January 2004 Date of withdrawal of any conflicting National Standard (dow): 31 January 2004 ETSI ETSI EN 300 019-2-4 V2.2.2 (2003-04) 5 1 Scope The present document specifies test methods and severities
18、for verification of the required resistibility of equipment according to the relevant environmental class. The tests defined in Part 2-4 of this multi-part standard apply to stationary use of equipment at non-weatherprotected locations covering the environmental conditions stated in EN 300 019-1-4 1
19、. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subseq
20、uent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ETSI EN 300 019-1-4: “Environmental Engineering (EE); Environmental c
21、onditions and environmental tests for telecommunications equipment; Part 1-4: Classification of environmental conditions; Stationary use at non-weatherprotected locations“. 2 IEC 60068-2: “Environmental testing - Part 2: Tests“. 3 ETSI EN 300 019-2-0: “Environmental Engineering (EE); Environmental c
22、onditions and environmental tests for telecommunications equipment; Part 2-0: Specification of environmental tests; Introduction“. 4 IEC 60721-3-4: “Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 4: Stationary
23、use at non-weatherprotected locations“. 5 ANSI T1.329-2000: “Network Equipment Earthquake Resistance Standard“. 6 ETSI ETR 035: “Equipment Engineering (EE); Environmental engineering Guidance and terminology“. 3 Environmental test specifications The detailed descriptions of the environmental conditi
24、ons are given in clauses 4 and 5 of EN 300 019-1-4 1. EN 300 019-2-0 3 forms a general overview of Part 2 of the present document. The equipment under test is assumed to be in its operational state throughout the test conditions described in the present document unless otherwise stated. The required
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ETSI EN-300-019-2-4-V2.2.2-2003 EN 300 019 V2 2.2 2003
链接地址:https://www.31doc.com/p-3756016.html