ETSI EN-300-019-1-0-2003.pdf
《ETSI EN-300-019-1-0-2003.pdf》由会员分享,可在线阅读,更多相关《ETSI EN-300-019-1-0-2003.pdf(10页珍藏版)》请在三一文库上搜索。
1、 ETSI EN 300 019-1-0 V2.1.2 (2003-09) European Standard (Telecommunications series) Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of environmental conditions; Introduction ETSI ETSI EN 300 019-1-0 V2.1.2 (2
2、003-09) 2 Reference REN/EE-01027-1-0 Keywords environment, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/
3、88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference versio
4、n is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of statu
5、s. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be reproduced except as authorized by written permissio
6、n. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are Trade Mark
7、s currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI EN 300 019-1-0 V2.1.2 (2003-09) 3 Contents Intellectual Property Rights4 Foreword.4 1 Scope5 2 References5
8、3 Definitions5 4 Environmental classes6 4.1 Purpose of classification.6 4.2 Environmental classes covered in Part 17 5 Explanation of climatograms8 6 Environmental contents of equipment documentation.8 6.1 Environmental considerations to be included in the design process for producing equipment8 6.2
9、 Environmental contents of a product specification 9 6.3 Contents of an environmental test programme.9 History10 ETSI ETSI EN 300 019-1-0 V2.1.2 (2003-09) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pe
10、rtaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secr
11、etariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (o
12、r the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Environmental Engineering (EE). The present document is part 1, sub-part 0 of a mult
13、i-part deliverable covering the classification of environmental conditions and environmental tests for telecommunications equipment, as identified below: Part 1: “Classification of environmental conditions“; Sub-part 0: “Introduction“; Sub-part 1: “Storage“; Sub-part 2: “Transportation“; Sub-part 3:
14、 “Stationary use at weatherprotected locations“; Sub-part 4: “Stationary use at non-weatherprotected locations“; Sub-part 5: “Ground vehicle installations“; Sub-part 6: “Ship environments“; Sub-part 7: “Portable and non-stationary use“; Sub-part 8: “Stationary use at underground locations“; Part 2:
15、“Specification of environmental tests“. Part 1 specifies different standardized environmental classes covering climatic and biological conditions, chemically and mechanically active substances and mechanical conditions during storage, transportation and in use. Part 2 specifies the recommended test
16、severities and test methods for the different environmental classes. National transposition dates Date of adoption of this EN: 5 September 2003 Date of latest announcement of this EN (doa): 31 December 2003 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 Jun
17、e 2004 Date of withdrawal of any conflicting National Standard (dow): 30 June 2004 ETSI ETSI EN 300 019-1-0 V2.1.2 (2003-09) 5 1 Scope The purpose of the present document is to select class(es) of environmental conditions and their severities to which equipment may be exposed. Only severe conditions
18、, which may be harmful to the equipment, are included. The severities specified are those which will have a low probability of being exceeded; generally less than 1 %. The purpose of the present document is to form a general overview of Part 1. TR 100 035 1 should be used in conjunction with all par
19、ts of EN 300 019 series. It gives an introduction to the main concepts of environmental engineering, the purpose and use of environmental classes and the corresponding test philosophy. 2 References The following documents contain provisions which, through reference in this text, constitute provision
20、s of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are
21、 not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ETSI TR 100 035: “Environmental Engineering (EE); Environmental engineering; Guidance and terminology“. 2 ETSI EN 300 019-1 (all subparts): “Environmental Engineering (EE); Environmental
22、 conditions and environmental tests for telecommunications equipment; Classification of environmental conditions“. 3 ETSI EN 300 019-2 (all subparts): “Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Specification of environmental te
23、sts“. 3 Definitions For the purposes of the present document, the following terms and definitions apply: environmental class: systematic representation of the environment for a family of locations with “similar properties“ NOTE: This means that the detailed description of the class may be envisaged
24、as an envelope around a group of related environmental conditions. The class itself may not be considered directly as a typical example. A class is composed of the most significant single factors, termed environmental parameters, selected from those factors which are assumed to influence equipment p
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ETSI EN-300-019-1-0-2003 EN 300 019 2003
链接地址:https://www.31doc.com/p-3756030.html