BS-ISO-500-3-2004.pdf
《BS-ISO-500-3-2004.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-500-3-2004.pdf(20页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 500-3:2004 Agricultural tractors Rear-mounted power take-off types 1, 2 and 3 Part 3: Main PTO dimensions and spline dimensions, location of PTO ICS 65.060.10 ? Licensed Copy: London South Bank University, London South Bank University, Sun Dec 24 04:41:31 GMT+00:00 2006, Unco
2、ntrolled Copy, (c) BSI BS ISO 500-3:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2006 BSI 2006 ISBN 0 580 49649 X National foreword This British Standard was published by BSI. It is the UK implementation of ISO 500-3:2004.
3、 This standard together with BS ISO 500-1:2004 and BS ISO 500-2:2004 supersedes BS 5861:1992, which is withdrawn. BS 5861:1992 was identical to ISO 500:1991. The UK participation in its preparation was entrusted to Technical Committee AGE/6, Agricultural tractors and forestry machinery. A list of or
4、ganizations represented on AGE/6 can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations.
5、Amendments issued since publication Amd. No. DateComments Licensed Copy: London South Bank University, London South Bank University, Sun Dec 24 04:41:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Reference number ISO 500-3:2004(E) INTERNATIONAL STANDARD ISO 500-3 First edition 2004-02-01 Agricultura
6、l tractors Rear-mounted power take-off types 1, 2 and 3 Part 3: Main PTO dimensions and spline dimensions, location of PTO Tracteurs agricoles Prises de force montes larrire des types 1, 2 et 3 Partie 3: Dimensions principales de la prise de force et dimensions des cannelures, emplacement de la pris
7、e de force BS ISO 500-3:2004 Licensed Copy: London South Bank University, London South Bank University, Sun Dec 24 04:41:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii Licensed Copy: London South Bank University, London South Bank University, Sun Dec 24 04:41:31 GMT+00:00 2006, Uncontrolled Copy,
8、(c) BSI iii Contents Page Forewordiv 1 Scope1 2 Normative references .1 3 PTO location1 4 Manufacturing requirements Main PTO and spline dimensions.3 Bibliography .13 BS ISO 500-3:2004 Licensed Copy: London South Bank University, London South Bank University, Sun Dec 24 04:41:31 GMT+00:00 2006, Unco
9、ntrolled Copy, (c) BSI iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested
10、in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commi
11、ssion (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technica
12、l committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shal
13、l not be held responsible for identifying any or all such patent rights. ISO 500-3 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 4, Tractors. This first edition of ISO 500-3, together with the first editions of ISO 500-1 and ISO 5
14、00-2, cancels and replaces ISO 500:1991, which has been technically revised. ISO 500 consists of the following parts, under the general title Agricultural tractors Rear-mounted power take-off types 1, 2 and 3 : Part 1: General specifications, safety requirements, dimensions for master shield and cle
15、arance zone Part 2: Narrow-track tractors, dimensions for master shield and clearance zone Part 3: Main PTO dimensions and spline dimensions, location of PTO BS ISO 500-3:2004 Licensed Copy: London South Bank University, London South Bank University, Sun Dec 24 04:41:31 GMT+00:00 2006, Uncontrolled
16、Copy, (c) BSI 1 Agricultural tractors Rear-mounted power take-off types 1, 2 and 3 Part 3: Main PTO dimensions and spline dimensions, location of PTO 1 Scope This part of ISO 500 specifies manufacturing requirements for, and the location of, rear-mounted power take- offs (PTOs) of types 1, 2 and 3 o
17、n agricultural tractors. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. I
18、SO 6508 (all parts), Metallic materials Rockwell hardness test 3 PTO location The location of the PTO on the tractor shall be in accordance with Figure 1 and Table 1. The location of the PTO axis shall lie within the shaded rectangle shown in Figure 1 and in accordance with Table 1, parallel to the
19、longitudinal axis of the tractor and should be parallel to the ground, within 3. The value of the dimensions h (see Table 1) are for normal agricultural applications. On tractors especially designed for high ground clearance, such as working in standing vegetable crops or sugar cane, hmax, may excee
20、d the given values. On agricultural tractors designed for low ground clearance, such as lawn mowing or ground care which require a low centre of gravity, hmin, may be less than the given values. BS ISO 500-3:2004 Licensed Copy: London South Bank University, London South Bank University, Sun Dec 24 0
21、4:41:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 2 Dimensions in millimetres Key 1 centre line of tractor 2 track width Figure 1 PTO location Table 1 PTO location Dimensions in millimetres PTO type hmin hmax 1 480 800 2 530 900 3 600 1 000 BS ISO 500-3:2004 Licensed Copy: London South Bank Univers
22、ity, London South Bank University, Sun Dec 24 04:41:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 3 4 Manufacturing requirements Main PTO and spline dimensions The dimensions of the rear PTO on agricultural tractors and the mating part of the PTO drive shaft shall comply with: Figure 2 and Table 2,
23、for PTO dimensions; Figure 3 and Table 3, for external, straight-sided spline dimensions Type 1; Figure 4 and Table 4, for internal, straight-sided spline dimensions Type 1; Figure 5 and Table 5, for external, involute spline dimensions Type 2; Figure 6 and Table 6, for internal, involute spline dim
24、ensions Type 2; Figure 7 and Table 7, for external, involute spline dimensions Type 3; Figure 8 and Table 8, for internal, involute spline dimensions Type 3. The hardened portion of the splines shall have a minimum surface hardness of 48 HRC when tested in accordance with ISO 6508. NOTE For general
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS ISO 500 2004
链接地址:https://www.31doc.com/p-3756131.html