GME-01114-1999.pdf
《GME-01114-1999.pdf》由会员分享,可在线阅读,更多相关《GME-01114-1999.pdf(34页珍藏版)》请在三一文库上搜索。
1、STD=OPEL GME OLLLLi-ENGL 1999 B597LL8 0028382 4Lb General Specification Body GME 01114 Test of Ashtray berprfung Ascher 1 Introduction 1.1 Scope. This specification is applicable to: - ashtrays with tip systems - ashtrays with folding systems - ashtrays with rotating systems - ashtrays with drawer s
2、ystems 1.2 Mission I Theme. Testing the ashtray cording to various performance criteria. 1.3 Classification. Not applicable. I Einfhrung 1 .i Anwendungsbereich. Diese Spezifikation ist anwendbar fr: - Ascher mit Tip-System - Ascher mit Klapp-System - Ascher mit Dreh-System - Ascher mit Schubladen-Sy
3、stem 1.2 Aufgabe I Thema. berprfung des Aschers nach verschiedenen Leistungskriterien. 1.3 Einteilung. Nicht anwendbar. ac- Note: Nothing in the specification, however, su- Hinweis: Falls keine Ausnahmen vereinbart wur- persedes applicable laws and regulations unless a den, darf die Vorschrift keine
4、 anzuwendenden specific exemption has been obtained. Gesetze und Regelungen auer Kraft setzen. Note: In the event of a conflict between the Ger- Hinweis: Im Falle von Unstimmigkeiten zwischen man and the English language, the German lan- dem deutschen und dem englischen Text ist der guage shall take
5、 precedence. deutsche Text ausschlaggebend. 2 References 2 Referenzen Note: Only the latest approved standards are Hinweis: Wenn nicht anders angegeben, ist applicable unless otherwise specified. jeweils die neueste Fassung der angegebenen Referenz gltig. 2.1 Normative. None. 2.1 Normative. Keine. 2
6、.2 GM. 2.2 GM. GMUTS UR-0-1 2.3 Additional. None. 2.3 Zustzliche. Keine. 3 Test Preparation and Evalua- tion Auswertung 3 Prfungsvorbereitung und 3.1 Resources. 3.1.1 Calibration. The test facilities and equip- ment shall be in good working order and shall have a valid calibration label. 3.1.2 Alter
7、natives. Alternative test facilities and equipment may aiso be used. !-kifieiei, a! r a s - uring variables as specified in this specification shall be determined correctly with respect to its physical definition. 3.1 Gerte und Einrichtungen. 3.1 .I Kalibrierung. Alle Prfeinrichtungen und -ausrstung
8、en mssen funktionsfhig sein und eine gltige Kalibrierplakette haben. 3.1.2 Alternativen. Es knnen auch alternative Prifeinrichtungen und -ausrstungen verwendet werden. Alle Messvariablen, wie sie in dieser Vor- schrift angegeben werden, mssen jedoch in Be- zug auf ihre physikalische Definition korre
9、kt fest- gelegt werden. O Copyright 1999 General Motors Corporation All Rights Reserved Originating Department: ITDC - Specification Center Page 1 of 34 November 1999 LBSP GME GS 1 05/99 GME 01114 GM ENGINEERING STANDARD EUROPE 3.1.3 Facilities. 3.1.3.1 Dudenhofen test center or equivalent proving g
10、round (torture track left, Belgian block wave road; Rheinstrae). 3.1.3.2 Motorway, federal road, cobblestones. 3.1.3.3 Climatic chamber. 3.1.3.4 Durability test stand. 3.1.4 Equipment. 3.1.4.1 Tensile / compression gauge with hook, piston with a diameter of 10 mm and clamp; measuring range (0.30) N.
11、 3.1.4.2 Caliper gauge. 3.1.4.3 Tape measure. 3.1.4.4 Steel ruler. 3.1.4.5 Contactless device for measurement of opening time. 3.1.4.6 Filling for volumetric measurement. 3.1.4.7 Finished sizes. 3.2 Test Samples. - ashtray with tip system - ashtray with folding system - ashtray with rotating system
12、- ashtray with drawer system 3.3 Conditioning. Not applicable. 3.4 Documentation. Samples of components or material released to this specification shall be tested for conformity with the requirements of this specification and approved by the responsible GM Department prior to the start of delivery o
13、f produc- tion level components or materials. Any change to the component or material, e.g. design, function, properties, manufacturing proc- ess andlor location of manufacture requires a new release of the product. It is the sole responsibility of the supplier to provide the customer, unsolic- ited
14、, with documentation of any change or modifi- cation to the producprocess, and to apply for a new release. 3.1.3 Einrichtungen. 3.1.3.1 Testzentrum Dudenhofen oder quivalen- tes Prffeld (Marterstrecke links, Groblockwel- lenbahn; Rheinstrae). 3.1.3.2 Bundesautobahn, Bundesstrae, Kopf- steinpflaster.
15、 3.1.3.3 Klimakammer 3.1.3.4 Dauerprfstand. 3.1.4 Ausrstung. 3.1.4.1 Zug4Druckwaage mit Haken, Stempel mit einem Durchmesser von 10 mm und Klammer; Messbereich (OSO) N. 3.1.4.2 Mess-Schieber. 3.1.4.3 Rollbandma. 3.1.4.4 Stahllineal. 3.1.4.5 Vorrichtung zur berhrungslosen Messung der Offnungszeit. 3.
16、1.4.6 Fllung fr Volumenmessung. 3.1.4.7 Endmae. 3.2 Prteile. - Ascher mit Tip-System - Ascher mit Klapp-System - Ascher mit Dreh-System - Ascher mit Schubladen-System 3.3 Probenvorbehandlung. Nicht anwend bar. 3.4 Dokumentation. Freigabemuster fr die diese Vorschrift zutrifft, mssen nach dieser Vors
17、chrift geprft werden und von der verantwortlichen GM Abteilung genehmigt sein, ehe eine Lieferung erfolgen kann. nderungen von z.B. Aufbau, Funktion, Eigen- schaften, Herstellungsproze und Ort machen eine Neufreigabe notwendig. Der Hersteller ist verpflichtet, unaufgefordert den Abnehmer mit einer D
18、okumentation ber alle Abstimmungen, Modifikationen von Teilen und / oder Prozessen zu informieren und eine Neufreigabe zu beantra- gen O Copyright 1999 General Motors Corporation All Rights Reserved Page 2 of 34 November 1999 LBSP GME GS G 06199 -,-,- STDmOPEL GME 01114-ENGL 1999 8597118 0028384 299
19、 = GME 01114 GM ENGINEERING STANDARD EUROPE If not otherwise agreed to the entire verification test shall be repeated and documented by the supplier prior to start of delivery of the modified or changed product. In some cases a shorter test can be agreed to between the responsible GM Department and
20、the supplier 3.4.1 Test Results. Variables shall be provided for values which are not explicitly listed. The val- ues shall be entered in the drawing under the relevant variables. Subjective evaluation shall be made according to The results shall be entered in the relevant data sheets (Appendix B to
21、 E). 3.4.2 Deviations from Test Procedure. Devia- tions from the requirements of the test procedures shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports etc. GMUTS L/R-0-1. 3.4.2.1 All performance specifications shall be fulfilled withi
22、n a temperature range of 3.4.2.2 The following 3 temperature ranges shall be selected for the tests: (-30 .+ 80) “C. - (-30 .- 25) “C - (+20 .+ 25) “C - (+65 .+ 80) “C 4 Requirements and Test Proce- dure 4.1 General. The ashtray shall be checked for conformance to the current development/ release st
23、atus before each test. All fasteners shall be present, undamaged and correctly installed. If this is not the case, the fas- teners shall be supplemented or corrected. Any modifications shall be noted. The dimensions of the ashtray shall be deter- mined according I y. The volume shall be established
24、with filling mate- rial. The opening distance X shall be measured (see Figure 1). Wenn nicht anders vereinbart, ist die komplette Freigabeprfung durch den Lieferanten zu wie- derholen und das Ergebnis zu dokumentieren, bevor die nderungen in der Lieferung einsetzen knnen. In Einzelfllen kann zwische
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GME 01114 1999
链接地址:https://www.31doc.com/p-3766168.html