GME-QK-005600-1993.pdf
《GME-QK-005600-1993.pdf》由会员分享,可在线阅读,更多相关《GME-QK-005600-1993.pdf(8页珍藏版)》请在三一文库上搜索。
1、ADAM OPEL AG TEZ Werkstoff-Entwicklung Material-Development and Testinn Ausfertigungs-Nr.: Issue: Techn. Lieferbedingungen fr Werkstoffe ENG1 NEERING MATERIAL SPECIFICATION Datum: 07/93 . Ausgefertigt: Iru Genehmigt: Seite von 8 Date: Prepared: Biegeversuch/ Testing of plastics; flexural test Prfung
2、 von Kunststoffen; Schlagbiegeversuch/ Testing of plastics; determination of impact resistance Prfung von Kunststoffen; Zugversuch/ Testing of plastics; tensile test Prfung von Kunststoffen; Bestimmung des Elastizittsmoduls im Zug-, Druck- und Biegeversuch/ Testing of plastics; determination of the
3、modulus of elasticity by the tensile test, compression test and bending test Prfung von Kunststoffen; Bestimmung der Fombestndigkeits- temperatUr/ Testing of plastics; determination of heat deflection temperature under load Prfung von Kunststoffen und Elastomeren; Bestimmung der Dichte/ Testing of p
4、lastics and elastomers; detemination of density Prfung von Kunststoffen; Bestimmung des Schmelzindex von Thermoplasten/ Testing of plastics; determination of the melt flow index of thermoplastics Kunststoffe; Bestimmung der Hrte; Kugeleindnickversuch; Identisch mit IS0 2039-1:1987 Plastics; Determin
5、ation of hardness; Ball indentation method; Identical with IS0 2039-1:1987 I I I I I Opel Form. 66 174-1 E WD 1 88 -,-,- QK 005 600 4usfertigungs-Nr.: ssue: IS0 75 Datum: AusgeferigA Seite von Date: O7lg3 Prepared: Page 2 ai 8 IS0 178 IS0 179 1987 Plastics and Ebonite - Determination of Temperature
6、of Deflection under Load 1975 1982 Plastics - Determination of Flexural Properties of Rigid Plastics Plastics - Determination of the Charpy Impact Resistance of Rigid Plastics IS0 11 33 1991 Plastics - Determination of the Melt Flow Rate of Thermo- plastics IS0 11 83 1987 Plastics - Methods for Dete
7、mining the Density and relative Density of Non-cellular Plastics ISO/DIS 527 1985 Plastics - Detemination of tensile properties QK O00 O00 QU O00 O0 Information zur Handhabung der Technischen Lieferbedingun- gen fr Kunststoffe/ Information for handling of technical terms of delivery for plactics Anf
8、orderungen zur Erfllung von Umweltschutzgesetzer Requirements for fulfilling of environmental protedion laws 1 Zweck f Scope Diese Werkstoffvorschrift umfat die allgemeinen Anforderungen an Werkstoffiypen aus Polyacetal- Copolymerisat, die in gespritzter oder extrudierter Form fr Fomteile im Fahneug
9、bereich (2.B. Karosserie oder Chassis) zum Einsatz kommen./ This material specification discribes the general requirements of material types from polyacetal- copolymer, which are used in injected or extruded form for moulded compounds (e.9. body or chassis). 2 Werkstoff 1 Material Polyamtat-Copolyme
10、risat, (POM-Polyoximethylen)! Polyacetal-copolymer, (POM-Polyoximethylene) 3 Kurueichen f Symbol POMc 4 Verwendung Application Fr Formteile nach Zeichnung./ For finished parts to part drawing. 5 Lieferform f Form of Delivery Der Werkstoff w i r d als verarbeitungsfertiges Granulat angeliefert./ The
11、material shall be supplied in form of granules, ready for processing. -,-,- QK 005 600 hsfertigungs-Nr.: issue: 3 6 Anforderungen / Requirements 6.1 Die Mindestwerte der wichtigsten physikalischen, mechanischen und thermischen Eigenschaften sind in Tabellen zusammengefat. Die in den Tabellen angefhr
12、ten Werte werden, wenn nicht anders angegeben, an Probekrpem nach den dort angefhrten Prfnormen ermittelt. Alle Probekrper werden im Spritzgieverfahren unter optimalen Bedingungen hergestellt. Die Prfungen erfolgen bei einer Temperatur von +23“ C f 5 K und einer relativen Luftfeuchte von (50 f 5) K.
13、 Zustzliche in den Tabellen nicht erate Eigenschaften, wie 2.9. “Antistatikum“ usw. werden durch Kennbuchstaben nach der jeweiligen Spezifikationsnummer angegeben. Die Farbeinstellung wird in Zeichnungen, Werkstoftkorschriften und dergl. vorgeschrieben./ The minimum requirements regarding the most s
14、ignificant physical, mechanical and thermal properties are summarized in charts. If not otheiwise specified the values indicated in these charts will be determined on test pieces according to the respective test standards. All test pieces shall be injedion moulded and manufactured under optimum cond
15、itions. The tests shall be carried out at a temperature of +23* C i 5 K and a relative humidity of (50 f 5) %. Additional characteristics not included in the charts e.g. “Antistatic agent“ will be indicated by code letters after the respective specification number. The colour shall be specified on d
16、rawings, in material specifications and otherwise. Datum: Ausgefertigt: 4 Genehmigt: Seite von Date: O7Ig3 Prepared: Approved: Page 3 o 8 Kenn buchstaben Eigenschaften Code letters Properties F Brandschutzmittel Flame retahmt H Wrmealterungssta bilisator Heat aging stabilizer L Licht- und Witterungs
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GME QK 005600 1993
链接地址:https://www.31doc.com/p-3766917.html