《HDMI-1.3c.pdf》由会员分享,可在线阅读,更多相关《HDMI-1.3c.pdf(437页珍藏版)》请在三一文库上搜索。
1、 High-Definition Multimedia Interface Compliance Test Specification Version 1.3c Hitachi, Ltd. Matsushita Electric Industrial Co., Ltd. Philips Consumer Electronics, International B.V. Silicon Image, Inc. Sony Corporation Thomson Inc. Toshiba Corporation CONFIDENTIAL HDMI Licensing, LLC. Confidentia
2、l HDMI Compliance Test Specification Version 1.3c Preface Notice THIS SPECIFICATION IS PROVIDED “AS IS” WITH NO WARRANTIES WHATSOEVER, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, NO WARRANTIES OF MERCHANTABILITY, NONINFRINGEMENT, FITNESS FOR ANY PARTICULAR PURPOSE, OR ANY WARRANTY OTHERWISE A
3、RISING OUT OF ANY PROPOSAL, SPECIFICATION, OR SAMPLE. Hitachi, Ltd., Matsushita Electric Industrial Co., Ltd., Philips Consumer Electronics International B.V., Silicon Image, Inc., Sony Corporation, Thomson Inc., Toshiba Corporation and HDMI Licensing, LLC. disclaim all liability, including liabilit
4、y for infringement of any proprietary rights, relating to use of information in this specification. Copyright 2001-2007 by Hitachi, Ltd., Matsushita Electric Industrial Co., Ltd., Philips Consumer Electronics International, B.V., Silicon Image, Inc., Sony Corporation, Thomson Inc., and Toshiba Corpo
5、ration. All rights reserved. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted herein. Unauthorized use or duplication prohibited. “HDMI” and all associated logos are trademarks of HDMI Licensing, LLC. Third-party trademarks and servicemarks are
6、 property of their respective owners. HDMI Licensing, LLC. Confidential Page ii HDMI Compliance Test Specification Version 1.3c Document Revision History 1.3c 2008/07/25 Addition of TMDS Signal Generator (4.2.1.9) Addition of overmold value for Type C connector(5-1) Addition of test for Active cable
7、 and Converter cable(5-2, through 5-8) Removed Active Cable Test (5-9) Addition of New Cable Test (5-10, 5-11, 5-12, 5-13 and 5-14) Correction of Test for CEC root Repeater (7-14, 8-13, 9-5) Editorial correction (7-3, 8-9, 8-24, Table7-1, Table7-2) Clarification of Test Signal (7.4.1) Addition of te
8、st for Type 2 cable emulator (8-7) Clarification of Non-HDMI I/O (9.2.4) Modification of Repeater Mini-CDF for Source/Sink function (Appendix 3) Addition of CDF fields for Cable (Appendix 3) 1.3b1 2007/08/01 Added Efficere fixtures for Type C connector 1.3b 2007/03/16 Modifications to TE overview an
9、d policy description (4.1) Addition of Agilent TDR to Recommended TE (4.2.1.11) Clarification of tentative cable emulators (4.2.1.17) Jitter tolerance test changes (8-7) Added cable tests for TMDS_CLOCK channel (5-3) New VL triggering (7-2) Editorial and clarifications on CEC Line Degradation (7-15,
10、 8-14) Added testing of additional source-supported Deep Color formats (7-34) Additional HDMI VSDB EDID checks (8-3) Additional TTC usage (5-3, 8-5, 8-6, 8-7) Incorporated Tek-recommended setup and calibration for TDR (8-8) Clarification on Sink Deep Color Recommended Test Method (8-25) Added long c
11、able or cable emulator use for Repeater test (9-3) Added color-depths for each format in Source_Video_Formats (App. 3) Removed test for filler bytes (8-3) Removed Tektronix part number of cable emulator EFF-HDMI-CE-01 1.3a 2006/11/10 Clarified pixel clock vs. TMDS clock (throughout). Added new test
12、equipment and test fixtures from Agilent and Tektronix for high-speed testing (throughout) Added Reference Cable Equalizer to eye analysis equipment and tests. Added tests and test equipment capabilities for 1.3 features (Deep Color, cable categories, xvYCC, HBRA, Type C connector) Added testing of
13、1080p 50Hz/60Hz in various tests. Added Transition Time Control (TTC) equipment and usage (5-3, 8-7) Allowed use of any sufficient multi-meter, I2C analyzer and power supply. Added preliminary cable phase measurements for passive-equalized cables per HDMI 1.3a (5-7) Relaxed impedance requirements wi
14、th 250ps excursion window as specified in HDMI 1.3a (5-8, 8-8) Added preliminary active cable test (5-9) Modified VL limits, per HDMI 1.3 and 1.3a (7-2) Removed max rise/fall time limit, per HDMI 1.3a (7-4) Removed Source Overshoot/Undershoot test (7-5) Added 20-bit trigger sequence for Inter-Pair s
15、kew check (7-6) HDMI Licensing, LLC. Confidential Page iii HDMI Compliance Test Specification Version 1.3c Removed erroneous check of CLOCK in Inter-Pair skew check (7-7) Set jitter measurement window at 0V (7-9) Clarified which frequencies to test for jitter and eye (7-9, 7-10, 8-7). Changed CEC ca
16、pacitance limits, per HDMI 1.3a (7-13, 8-9) Added check for new AVI InfoFrame fields (7-27) Added optional testing of jitter injected onto TMDS_DATA (8-7) Perform HPD voltage in both standby and off (8-10) Eliminated VGA Established Timings check (8-20) Degraded input signal used for Repeater output
17、 test (9-1) Added check of Physical Address-related CDF fields (9-5) Added HDCP testing requirements (section 1). HDMI Licensing, LLC. Confidential Page iv HDMI Compliance Test Specification Version 1.3c 1.2a 2005/12/15 Incorporation of Quantum Data 882 for CEC and EDID tests (sects. 4.2.1.1.9, 4.2.
18、3.1, 4.2.3.2, Appendix 1) Add note regarding discontinued test equipment (sect.4.1.1) Added General Oscilloscope (4.2.3.4) New policy submit all longer cable length (sect. 5 first paragraph) Clarified extent of overmold restriction (5-1) Restricted cable power consumption to 5mA (5-3) Clarified use
19、of Tektronix TDR (5-8, 8-8) Clarified policy all connectors must be tested and results submitted (sect. 6 intro) Addressed capacitance measurement issues with TE and configuration change (7-13, 8-9) Replaced IOFF test with VOFF test (7-3) Adjusted HPD voltages per HDMI Spec (7-12) Verify legal usage
20、 of “independent CEC” function (7-14, 8-13) Adjusted CEC resistance allowance per HDMI Spec (7-14, 8-13) Adjusted CEC degradation check (7-15, 8-14) Removed Type A-related test (7-20) Verify compliance with audio-must-output rule (7-28) Changed audio/video format combinations to test (7-30) Added ma
21、x differential test and adjusted max VICM (8-5) Added new video formats (7-25, 7-26, 8-17) Removed DTD requirement per HDMI Spec (8-17) Clarified variety of TE specs (4.2.1.5, 4.2.1.9, 4.2.1.11, 4.2.1.16, 4.2.3.3, Clarified test methods and configurations (7-1, 7-3, 7-5, 7-6, 7-7, 7-11, 7- 1318, 7-2
22、333, 8-13, 8-5, 8-7, 8-9, 8-14, 8-1623, 9-19-5) Numerous clarifications in CDF fields (Appendix 3) 1.1 2004/06/04 Clarified Multi-meter vs. Voltage meter usage (throughout). Changed to SMA version of differential probe (sect. 4.2.1.5, 7-5, 7-10). Clarified test conditions and procedures (5-3, 7-10,
23、7-23, 7-24, 7-25, 7- 27, 7-29, 7-31, 8-7, 8-15, 8-17). Added testing of Type B connectors (5-1). Clarified testing of active, unidirectional cables (5-2). Clarified use of serial pattern trigger (7-6). Changed limits of +5V Power Signal per HDMI 1.1 change (7-11). Changed test conditions for DDC/CEC
24、 capacitance (7-13, 8-9). Simplified/clarified testing of CEC connectivity (7-14, 8-13). Added test conditions for CEC degradation (7-15, 8-14). Added tests for additional CTLx restrictions (7-17). Added tests for new HDMI 1.1 packets (7-19). Modified test requirements and methods for AVI check (7-2
25、7). Added check for channel status indication of Fs (7-28). Added check for extended HDMI VSDB handling (7-33). Verify HDMI VSDB extension fields new in HDMI 1.1 (8-3). Clarified initialization procedure and failure conditions (8-7). Changed limits of HPD voltage and test conditions per HDMI 1.1 cha
26、nge (8-10). Clarified testing of HPD for non-ordinary circumstances (8-11). Add testing for new Supports_AI capability HDMI 1.1 (8-16). Clarified EDID use and test of 640x480p format (8-20). Swapped tests to correct positions (9-2, 9-4). Updated ATC test equipment lists for new and evaluation TE (Ap
27、p. 1). HDMI Licensing, LLC. Confidential Page v HDMI Compliance Test Specification Version 1.3c Updated CDF with new fields for HDMI 1.1 and new tests (App. 3) Many editorial changes throughout. 1.0a 2003/07/22 Fix table in Test 7-22 1.0 2003/07/18 1.0 Release 0.9 2003/06/26 0.9 Release HDMI Licensi
28、ng, LLC. Confidential Page vi HDMI Compliance Test Specification Version 1.3c Table of Contents PREFACE II NOTICEII DOCUMENT REVISION HISTORY.III 1 INTRODUCTION 1 1.1 PURPOSE AND SCOPE. 1 1.2 NORMATIVE REFERENCES. 1 1.3 ORGANIZATION OF THIS DOCUMENT 1 2 DEFINITIONS 3 2.1 CONFORMANCE LEVELS 3 2.2 USA
29、GES AND CONVENTIONS. 3 2.3 GLOSSARY OF TERMS 4 2.4 ACRONYMS AND ABBREVIATIONS. 5 3 OVERVIEW . 6 4 TEST EQUIPMENT 7 4.1 TEST EQUIPMENT OVERVIEW AND POLICY 7 4.2 TEST EQUIPMENT REQUIREMENTS 7 5 TESTS CABLE ASSEMBLY. 38 5.1 CABLE MECHANICAL 39 5.2 CABLE ELECTRICAL: PERFORMANCE TESTS. 40 5.3 CABLE ELECT
30、RICAL: PARAMETRIC TESTS 51 5.4 CABLE ACTIVE CABLE TESTS. 64 6 TESTS PLUG AND RECEPTACLE. 71 6.1 MECHANICAL TESTS. 71 6.2 CONNECTOR ANSI 364 TESTS 72 7 TESTS SOURCE. 76 7.1 SOURCE PRODUCTS OVERVIEW. 76 7.2 SOURCE EDID / E-DDC / HPD 77 7.3 SOURCE ELECTRICAL 80 7.4 SOURCE PROTOCOL 125 7.5 SOURCE VIDEO.
31、 134 7.6 SOURCE AUDIO. 149 7.7 SOURCE INTEROPERABILITY WITH DVI. 160 HDMI Licensing, LLC. Confidential Page vii HDMI Compliance Test Specification Version 1.3c 7.8 SOURCE ADVANCED FEATURES 162 8 TESTS SINK 169 8.1 SINK PRODUCTS OVERVIEW 169 8.2 SINK EDID / E-DDC 170 8.3 SINK ELECTRICAL. 178 8.4 SINK
32、 PROTOCOL. 214 8.5 SINK VIDEO 217 8.6 SINK AUDIO 225 8.7 SINK INTEROPERABILITY WITH DVI 229 8.8 SINK ADVANCED FEATURES. 230 9 TESTS REPEATER 233 9.1 REPEATER PRODUCTS OVERVIEW. 233 9.2 INTERNAL FUNCTIONAL BLOCK CATEGORIZATION. 233 9.3 TESTS OF OUTPUT PORTS 236 9.4 TESTS OF INPUT PORTS 238 9.5 TESTS
33、FOR PHYSICAL ADDRESS HANDLING 240 10 TESTS HDCP 242 10.1 OVERVIEW 242 10.2 TEST METHOD. 242 APPENDIX 1 AUTHORIZED TESTING CENTER TEST EQUIPMENT LIST . 243 STANDARD ATC CONFIGURATIONS:. 243 HIGH-SPEED CONFIGURATIONS. 247 APPENDIX 2 SOFTWARE CRU TECHNOLOGY 251 APPENDIX 3 CAPABILITIES DECLARATION FORM
34、(CDF) 256 SOURCE/SINK/REPEATER CHARACTERISTICS 256 SOURCE CHARACTERISTICS. 257 SINK CHARACTERISTICS 263 REPEATER CHARACTERISTICS. 267 CABLE ASSEMBLY CHARACTERISTICS 269 APPENDIX 4 TEST RESULTS FORM 271 TEST RESULTS FORM SOURCE DUT. 272 TEST RESULTS FORM SINK DUT 276 TEST RESULTS FORM REPEATER DUT .
35、280 TEST RESULTS FORM CABLE ASSEMBLY DUT. 281 HDMI Licensing, LLC. Confidential Page viii HDMI Compliance Test Specification Version 1.3c TEST RESULTS FORM PLUG 10k 1%, 0.25W For Source testing 1.2k 1% Recommended Test Equipment Any resistor with the Required Capabilities is sufficient. HDMI Complia
36、nce Test Specification Version 1.3c Section 4 Test Equipment HDMI Licensing, LLC. Confidential Page 26 of 284 4.2.1.15 DC Power Supply Required Test Equipment Capabilities Can output DC 3.3V and 5V with accuracy of 1% Maximum output current can be set with accuracy of 5% over the 10 to 100mA range.
37、Recommended Test Equipment Any DC power supply meeting the above requirements may be used. One such option is: KENWOOD PW18-1.8AQ 4.2.1.16 Digital LCR Meter Required Test Equipment Capabilities Test signal specification - Frequencies: 100kHz - AC level: 2.5Vp-p and 3.5Vp-p - DC level: 1.65V and 2.5V
38、 Resolution is equal or less than 1pF Accuracy is equal or less than 1pF Recommended Test Equipment HIOKI 3522-50 Digital LCR Meter HIOKI 9143 Probe HIOKI 9268-01 DC Bias unit 4.2.1.17 HDMI Cable Emulators HDMI cable emulators are intended to emulate the characteristics of worst-case but compliant c
39、ables. All of the cable emulators can be used with all of the TMDS Signal Generators and must be made available for all of the TMDS Signal Generators. Required Test Equipment Capabilities Attenuation or skew affected TP2 eye degradation or ISI jitter is compliant with cable specification. TMDS_DATA
40、jitter degradation of 0.2 TBIT 0.015 TBIT measured at the crossing point. Output signal meet TP2 eye mask at four corners exept for most left and most right point. Recommended Test Equipment Tentative There are three types of recommended HDMI cable emulators, each targeting a different type of signa
41、l degradation but compliant with cable specification on the TMDS channels. HDMI Compliance Test Specification Version 1.3c Section 4 Test Equipment HDMI Licensing, LLC. Confidential Page 27 of 284 Type 1 The Type 1 cable emulators have typical copper attenuation and inter-symbol interference (ISI) e
42、ffects. When a 74.25MHz TP1 worst-case signal is applied to the input of the Category 1 emulator, it will output a worst-case TP2 signal that still meets the TP2 eye mask but with approximately 0.2Tbit of ISI. The Category 2 device has the same characteristics, but for 165MHz signals. Category 1: Ag
43、ilent E4887A-101 Category 2: Agilent E4887A-102 Type 2 The Type 2 cable emulators degrade the TMDS signals through large intra-pair skew, slight attenuation and very slight ISI. When a TP1 worst-case signal is applied to the input, it will generate an almost worst-case TP2 signal, with horizontal de
44、gradation primarily due to intra-pair skew. There are two versions: one for 27MHz and one for 74.25MHz testing. 27MHz: JAE DC1P19ST02700AA 75MHz: JAE DC1P19ST07425AA Type 3 The Type 3 cable emulators are intended to emulate passive equalized cables and primarily attenuate the signal and add a very s
45、light amount of ISI. They are used for testing at all Category 2 rates. At both 165MHz (measured without Reference Cable Equalizer) and at 340MHz (measured after application of Reference Cable Equalizer), a worst-case TP1 eye will output a TP2 eye with the 4 corner points of the eye nearly touching.
46、 Agilent E4887A-103 (or E4887A-104 equivalent which is divided into eight modules.) 4.2.1.18 Transition Time Converter Transition time converters are used to control the slew rate of the TMDS Signal Generator to create a consistent slew rate among the different generators and to attain a slew rate t
47、o match a particular eye diagram. Required Test Equipment Capabilities TTC is implemented in hardware (at the output of the Signal Generator) and may be optionally implemented in software (in the Digital Oscilloscope) as an equivalent method for cable testing. When used with a particular TMDS Signal
48、 Generator, the transition time converter will decrease the slew rate such that the slew rate near the middle of the swing will match that of the left edge of the HDMI-specified TP1 eye at a particular test frequency. - Software TTC is applied during the calculation of the eye diagram by applying a
49、mathematical TTC that is equivalent to the hardware TTC requirement above. TTCs are used for all of the recommended TMDS Signal Generators and at the following test frequencies: HDMI Compliance Test Specification Version 1.3c Section 4 Test Equipment HDMI Licensing, LLC. Confidential Page 28 of 284 - 74.25MHz, 165MHz, 340MHz required for testing cables - 74.25MHz, 148.5MHz, 222.75MHz required for testing Sink DUTs Recommende
链接地址:https://www.31doc.com/p-3767102.html