GMW-3116-2008.pdf
《GMW-3116-2008.pdf》由会员分享,可在线阅读,更多相关《GMW-3116-2008.pdf(13页珍藏版)》请在三一文库上搜索。
1、 WORLDWIDE ENGINEERING STANDARDS Material Specification General GMW3116 Recyclability/Recoverability Copyright 2008 General Motors Corporation All Rights Reserved August 2008 Originating Department: North American Engineering Standards Page 1 of 13 1 Scope The purpose of this specification is to fac
2、ilitate compliance with current and future legislation. This standard also contains a guideline section for the GM design and supplier community to design in more recyclable / recoverable products that have maximum end of life value (see section 4). The guideline section is written for current techn
3、ology. As technology progresses the design guide will be updated. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. 70/156/EEC ISO 1043-2 2000/53/EC ISO 1629 2003/138/EC ISO 11469 2005/64/EC ISO 22628:2002 ISO 1043
4、-1 2.2 GM Standards/Specifications. GMW3059 2.3 Additional References. GM1738 3 Design Requirement 3.1 Marking of Polymeric Parts. Polymeric parts shall be labeled. 3.1.1 Marking of Plastic Parts. For the labelling and identification of vehicle plastic components and materials having a weight of mor
5、e than 100 g, the following nomenclature applies: ISO 1043-1 Plastics symbols and abbreviated terms. Part 1: Basic polymers and their special characteristics. ISO 1043-2 Plastics symbols and abbreviated terms. Part 2: Fillers and reinforcing materials. ISO 11469 Plastics Generic identification and m
6、arking of plastic products. 3.1.2 Marking of Rubber Parts. For the labelling and identification of vehicle elastomer components and materials having a weight of more than 200 g, the following nomenclature applies: ISO 1629 Rubbers and Latices Nomenclature. This shall not apply to the labelling of ty
7、res. 3.2 Restricted and Reportable Substances for Parts (GMW3059). All materials supplied to GM must comply with GMW3059, Restricted and Reportable Substances for Parts, latest version. 3.3 Component Parts Deemed to be Non Reusable. Component parts deemed to be non reusable according to the Directiv
8、e 2005/64/EC, Annex V, and its amendments, shall not be reused in new vehicles. 3.4 Vehicle Recyclability/Recoverability. The vehicle Recyclability/recoverability calculation shall be carried out per ISO 22628, Road vehicles - Recyclability and recoverability Calculation method. 3.4.1 Material Compo
9、sition. To comply with the Type Approval Directive 70/156/EEC, the supplier must enter the material composition in IMDS at the Prototype Build Phase for the Reference vehicle parts. GM will notify supplier of which parts and when this information is needed for the Prototype Build Phase. 3.5 Design f
10、or Dismantling. 3.5.1 Parts listed in Appendix A, Table A1, should be designed for dismantling. 3.5.2 Parts listed in Appendix A, Table A1, intended for the Korean market must be designed for 85% recyclability / 95% recoverability, by Dismantling. 3.5.3 Part Recyclability Calculation. The calculatio
11、n sheet in Appendix A, Table A4 can be used to calculate the % Recyclability of a part. 3.5.4 Part Recoverability Calculation. The calculation sheet in Appendix A, Table A4 can be used to calculate the % Recoverability of a part. GMW3116 GM WORLDWIDE ENGINEERING STANDARDS Copyright 2008 General Moto
12、rs Corporation All Rights Reserved Page 2 of 13 August 2008 4 General Design Guidelines 4.1 Material Selection. 4.1.1 Standardize Material Selection. Use the same material type(s) on specific components or subsystems across product lines. 4.1.2 Select Recyclable Materials. Select materials for which
13、 recycling technologies are currently practiced according to the European Council for Automotive R some type of added material to improve properties and some contaminants can be removed with a screen. This material will either be post-industrial or post-consumer depending on the source. 5.2 Acronyms
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GMW 3116 2008
链接地址:https://www.31doc.com/p-3767564.html