GOST-7566-1994-ENG.pdf
《GOST-7566-1994-ENG.pdf》由会员分享,可在线阅读,更多相关《GOST-7566-1994-ENG.pdf(26页珍藏版)》请在三一文库上搜索。
1、GOST 7566-94 GOST 7566-94 INTERSTATE STANDARD METAL PRODUCTS ACCEPTANCE, MARKING, PACKING, TRANSPORTATION AND STORAGE Official Edition English Version Approved by Interstandard INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION Minsk GOST 7566-94 Preface 1 THIS STANDARD IS DEVELOPED
2、 by the Ukrainian State Research and Development Institute of Metals THIS STANDARD IS SUMBITTED by the State Committee for Standardization, Metrology and Certification of Ukraine 2 THIS STANDARD IS ACCEPTED by the Interstate Council for Standardization, Metrology and Certification, October 21, 1994.
3、 Votes in favor: State National Standards Body Republic of Azerbaijan Azgosstandart Republic of Armenia Armgosstandart Republic of Belorussia Belstandart Georgia Gruzstandart Republic of Kazakhstan Gosstandart of the Republic of Kazakhstan Republic of Kirghizia Kirghizstandart Republic of Moldova Mo
4、ldovstandart Russian Federation Gosstandart of Russia Republic of Uzbekistan Uzgosstandart Ukraine Gosstandart of Ukraine 3. By Decree No. 185, dated May 21, 1997, of the State Committee of the Russian Federation for Standardization, Metrology and Certification Interstate Standard GOST 7566-94 is in
5、troduced as a State Standard of the Russian Federation from January 1, 1998. 4. IN PLACE OF GOST 7566-81 IPK Standards Publishing House, 1997 This Standard may not be reproduced, in full or in part, reprinted or distributed as an official publication in the territory of the Russian Federation withou
6、t the permission of Gosstandart of Russia. -,-,- GOST 7566-94 Contents 1 Scope 4 2 Reference documentation 4 3 Acceptance procedures 5 4 Marking 7 5 Packing . 11 6 Transportation and storage. 22 Appendix A . 23 GOST 7566-94 4 INTERSTATE STANDARD METAL PRODUCTS Acceptance, marking, packing, transport
7、ation and storage Date of Introduction: 01.01.98 1. SCOPE This Standard establishes the requirements for the acceptance, marking, packing, transportation and storage of blooms, slabs, billets, including cast and forged sections, bars, structural shapes, sized and cold-drawn rolled stock, wires, roll
8、ed products with a special surface finish, roll-formed sections, plates, large gauge rolled sections and strips. 2. REFERENCE DOCUMENTATION This Standard includes references to the following standards: GOST 9.014-78 ESZKS. Temporary corrosion protection of products. General technical requirements GO
9、ST 515-77. Bitumenized and tar-impregnated packaging paper. Specifications GOST 2991-85. Non-demountable wooden crates for cargoes of up to 500 kg. General technical specifications GOST 3282-74. General purpose low-carbon steel wire. Specifications GOST 5530-81. Packaging and industrial fabric. Spec
10、ifications GOST 6009-74. Hot-rolled steel strip. Specifications GOST 8828-89. Base paper and twin-layer water-resistant packaging paper. Specifications Official Edition GOST 7566-94 5 GOST 9569-79. Waxed paper. Specifications GOST 9998-86. Plasticized polyvinyl chloride films for domestic use. Gener
11、al technical specifications GOST 10198-91. Wooden cases for cargoes of from 200 to 20,000 kg. General technical specifications GOST 10354-82. Polyethylene film. Specifications GOST 14192-96. Marking of cargoes GOST 16272-79. Plasticized polyvinyl chloride film for industrial use. Specifications GOST
12、 20799-88. Industrial oils. Specifications GOST 21650-76. Means for fastening piece loads in transportation packages. General requirements GOST 26653-90. Preparation of general cargo for transportation. General requirements 3 ACCEPTANCE PROCEDURES 3.1. Metal products shall be accepted in batches. 3.
13、2. The size of batches and the scope of tests shall be established in the specifications for specific types of metal products. Batches of metal products shall be subjected to quality tests and accepted by the manufacturer. Where batches of products require control of the surface quality and dimensio
14、ns of each product in the batch, acceptance may be carried out based on the results of process control and inspection in the course of manufacturing. In the case of disagreement between the manufacturer and the customer, metal products shall be accepted in accordance with the requirements of standar
15、ds for specific types of products. 3.3. When testing the surface quality of rolled coils (bundles), rolled plate from continuous mills cut into sheets and roll-formed sections a batch shall be considered as complying with the requirements of the Standard if the weight of areas failing to comply with
16、 the surface quality requirements of the Standard does not exceed 2 % of the weight of the batch. If agreed upon by the customer and the manufacturer, the weight of areas failing to comply with the surface quality requirements of the Standard shall not exceed 5 % of the weight of the batch. If defec
17、tive surface areas of rolled products are revealed at the customers and presented to the manufacturer, the latter shall compensate the customer by an equivalent amount of rolled products of adequate quality. -,-,- GOST 7566-94 6 The weight of the cut-out defective areas shall be determined by weighi
18、ng. The weight of defective areas may be determined using the procedure outlined in Appendix A. 3.4. If unsatisfactory results are obtained for any one of the parameters the test shall be repeated. The scope of repeated tests shall be as follows: - For metal products subject to tests by sampling dou
19、ble the number of billets, blooms, slabs, bars, bundles, sheets, strips or coils shall be tested; - For metal products subject to complete (piece-by-piece) control repeated tests shall be carried out with double the number of specimens taken from billets, blooms, slabs, bars, sheets, strips or coils
20、 that failed the test. 3.5. The results of repeated tests shall be extended to the entire batch in the case of tests by sampling, or to billets, blooms, slabs, bars, sheets, strips, bundles and coils in the case of complete control. 3.6. If unsatisfactory results are obtained in the repeated tests,
21、the manufacturer may carry out a complete control of the parameters that failed the tests. 3.7. Each batch of metal products shall be accompanied by a document stating the following: - Name and/or trademark of the manufacturer; - Name of the customer; - Order number; - Date of drawing up the quality
22、 certificate; - Grade of steel, group or class of strength; - Number of smelt or batch if the smelt is divided into batches; - Name of metal product, size, number of pieces, their total weight; also the sign “TM“ when transporting according to the delivery (calculated) weight, conversion factor (wit
23、h rolled sheet the calculated weight of one sheet or of 1 m of length of coiled product may be stated instead), data on groups and categories of the rolled product in relation to their properties, surface quality, application, as well as other requirements specified in the respective specifications;
24、 - Number of regulatory document; - Chemical composition of steel from ladle samples or finished product; - Results of all tests including optional parameters at the customers request. Instead of the results of all tests it is permitted to state: “The metal product complies with the specifications o
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GOST 7566 1994 ENG
链接地址:https://www.31doc.com/p-3767596.html