GOST-16523-1997-ENG.pdf
《GOST-16523-1997-ENG.pdf》由会员分享,可在线阅读,更多相关《GOST-16523-1997-ENG.pdf(16页珍藏版)》请在三一文库上搜索。
1、GOST 16523-97 INTERSTATE STANDARD ROLLED SHEETS MADE OF QUALITY AND ORDINARY CARBON STEEL FOR GENERAL PURPOSE Specifications Official Edition English Version Approved by Interstandard INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION Minsk CORRECTIONS INSERTED INTO INTERSTATE STAND
2、ARDS B. METALS AND METAL PRODUCTS Group B23 to GOST 16523-97 Rolled sheets made of quality and ordinary carbon steel for general purpose. Specifications In what place Is printed Shall be printed Clause 4.1.3. Table 1 Column: “Strength group 390”. For category 5 of production mode “Cold-rolled” - + (
3、IUS Standards Information Catalog No. 8, 2000) -,-,- 16523-97 II Foreword 1 DEVELOPED by Ukraine Technical committee TC4 “Cast-iron, rolled sheet metal, rolled profiled heat-strengthened metal, rolling-stock products, metae and NP” SUBMITTED by Ukraine State Committee for Standardization, Metrology
4、and Certification. 2 APPROVED by Decree No. 11, dated 23.04.97, of Interstate Council for Standardization, Metrology and Certification Votes in favor: State National Standards Body Republic of ArmeniaArmgosstandart Republic of Belarus Gosstandart of Belarus Republic of Kazakhstan Gosstandart of Repu
5、blic of Kazakhstan Republic of Kirghizia Kirgizstandart Russian Federation Gosstandart of Russia Republic of Tadjikistan Tadjikgosstandart Republic of Uzbekistan Uzgosstandart Ukraine Gosstandart of Ukraine 3 This Standard is in compliance with International Standards ISO 3573-86, ISO 3574-86, ISO 4
6、995-91 and ISO 4997-78 regarding the requirements for rolled carbon steel of high and ordinary quality. 4 Interstate Standard GOST 16523-97 is introduced directly as the State Standard of the Russian Federation since 01.01.2000 by Decree No. 113, dated 04.04.99, of State Committee of the Russian Fed
7、eration for Standardization and Metrology. 5 IN PLACE OF GOST 16523-89 Standards Publishing House, 1999 This Standard may not be reproduced, in full or in part, reprinted or distributed as an official publication in the territory of the Russian Federation without the permission of Gosstandart of Rus
8、sia. 16523-97 III Contents 1 Scope. 1 2 Normative references. 1 3 Classification, key parameters and dimensions 2 4 General technical requirements. 2 4.1 Characteristics. 2 4.2 Performance characteristics established at the customers request. 6 4.3 Marking 8 4.4 Packing. 8 5 Acceptance procedure. 8
9、6 Test methods. 8 7 Transportation and storage 9 Appendix A. Scheme of conventional designations of rolled steel 10 Appendix B. Used steel grades. 11 16523-97 1 INTERSTATE STANDARD ROLLED SHEETS MADE OF QUALITY AND ORDINARY CARBON STEEL FOR GENERAL PURPOSE Specifications Introduced from 01.01.2000 1
10、 Scope This Standard applies to hot-rolled and cold-rolled sheets made of quality and ordinary carbon steel for general purpose, produced 500 mm and more wide and up to 3.9 mm thick inclusive. 2 Normative references The following standards are referred to in this Standard: GOST 380-94 Ordinary carbo
11、n steel. Grades GOST 1050-88 Profiled gaged structural quality carbon rolled steel with special surface finish. General specifications GOST 1497-84 Metals. Tensile test methods GOST 1763-68 Steel. Methods for determination of decarbonized layer thickness GOST 2284-79 Cold-rolled strip made of carbon
12、 structural steel. Specifications GOST 2789-73 Surface roughness. Parameters and characteristics GOST 5639-82 Steels and alloys. Methods of revelation and determination of grain size GOST 5640-68 Steel. Metallographic method for evaluation of strips and sheets microstructure GOST 7564-97 Steel. Gene
13、ral rules for selecting of samples, billets and specimens for mechanical and technological tests GOST 7565-81 Cast-iron, steel and alloys. Sampling method for determination of chemical composition GOST 7566-94 Metal products. Acceptance procedure, marking, packing, transportation and storage GOST 90
14、13-59 Metals. Method of Rockwell hardness measurement GOST 10510-80 Metals. Erichsen test method by extrusion of strips and sheets GOST 11701-84 Metals. Tensile test methods for thin strips and sheets GOST 14019-80 Metals and alloys. Bend test methods GOST 18895-97 Steel. Method of photoelectric spe
15、ctral analysis GOST 19903-74 Hot-rolled sheet steel. Assortment GOST 19904-90 Cold-rolled sheet steel. Assortment GOST 22536.0-87 Carbon steel and unalloyed cast-iron. General requirements for methods of analysis GOST 22536.1-88 Carbon steel and unalloyed cast-iron. Methods for determination of tota
16、l carbon and graphite Official Edition -,-,- 16523-97 2 GOST 22536.2-87 Carbon steel and unalloyed cast-iron. Methods of sulfur content determination GOST 22536.3-88 Carbon steel and unalloyed cast-iron. Methods of phosphorus content determination GOST 22536.4-88 Carbon steel and unalloyed cast-iron
17、. Methods of silicon content determination GOST 22536.5-87 Carbon steel and unalloyed cast-iron. Methods of manganese content determination GOST 22536.6-88 Carbon steel and unalloyed cast-iron. Methods of arsenic content determination GOST 22536.7-88 Carbon steel and unalloyed cast-iron. Methods of
18、chromium content determination GOST 22536.8-87 Carbon steel and unalloyed cast-iron. Methods of copper content determination GOST 22975-78 Metals and alloys. Method of Rockwell hardness measurement (Super Rockwell hardness) for light loads 3 Classification, key parameters and dimensions 3.1 Rolled s
19、teel products are subdivided: by manufacture mode: - hot-rolled steel; - cold-rolled steel; into types: - sheet steel; - coiled steel; by minimum value of ultimate strength (B) into strength groups: 260, 270, 300, 310, 330, 350, 360, 370*, 390, 400, 490; by standardized characteristics into categori
20、es: 1, 2, 3, 4, 5, 6; by surface finish quality into groups: - for cold-rolled steel: especially high quality of surface finish - I*; high-quality of surface finish - II; heightened quality of surface finish - III (IIIa, IIIb); - for hot-rolled steel: heightened quality of surface finish - III; ordi
21、nary quality of surface finish - IV; by drawing ability (up to 2 mm thick cold-rolled steel of strength groups 260, 270, 310, 330, 350): - deep-drawn - ; - normal-drawn - . 3.2 Regarding its assortment the rolled steel shall be in compliance with the following requirements: - hot-rolled steel shall
22、be in compliance with GOST 19903; - cold-rolled steel shall be in compliance with GOST 19904. 3.3 The scheme of conventional designations is specified in Appendix A. 4 General technical requirements 4.1 Characteristics 4.1.1 Rolled metal products shall be manufactured: - from ordinary carbon steel o
23、f the following strength groups: 300, 360, 370, 400; - from quality carbon steel of the following strength groups: 260, 270, 310, 330, 350, 390, 490. N o t e . The strength group shall be designated by three numerals corresponding to the lower limit of ultimate strength. Ordinary rolled steel shall
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GOST 16523 1997 ENG
链接地址:https://www.31doc.com/p-3767718.html