HD-605-S1-A2-1001.pdf
《HD-605-S1-A2-1001.pdf》由会员分享,可在线阅读,更多相关《HD-605-S1-A2-1001.pdf(22页珍藏版)》请在三一文库上搜索。
1、 Dansk Standard Tillg DS/HD 605 S1/A2 1. udgave 2001-06-08 Elektriske kabler Yderligere prvningsmetoder Electrical cables Additional test methods DS-publikationstyper Dansk Standard udgiver forskellige publikationstyper. Typen p denne publikation fremgr af forsiden. Der kan vre tale om: Dansk standa
2、rd standard, der er udarbejdet p nationalt niveau eller er baseret p et andet lands nationale standard, eller standard, der er udarbejdet p internationalt og/eller europisk niveau og har fet status som dansk standard DS-information publikation, der er udarbejdet p nationalt niveau og ikke har opnet
3、status som standard, eller publikation, der er udarbejdet p internationalt og/eller europisk niveau og ikke har fet status som standard, fx en teknisk rapport, eller europisk prstandard DS-hndbog samling af standarder eventuelt suppleret med informativt materiale DS-hfte publikation med informativt
4、materiale Til disse publikationstyper kan endvidere udgives tillg og rettelsesblade DS-publikationsform Publikationstyperne udgives i forskellig form som henholdsvis fuldtekstpublikation (publikationen er trykt i sin helhed) godkendelsesblad (publikationen leveres i kopi med et trykt DS-omslag) elek
5、tronisk (publikationen leveres p et elektronisk medie) DS-betegnelse Alle DS-publikationers betegnelse begynder med DS efterfulgt af et eller flere prfikser og et nr. fx DS 383, DS/EN 5414 osv. Hvis der efter nr. er angivet et A eller Cor, betyder det, enten at det er et tillg eller et rettelsesblad
6、 til hovedstandarden, eller at det er indfrt i hovedstandarden. DS-betegnelse angives p forsiden. Overensstemmelse med anden publikation: Overensstemmelse kan enten vre IDT, EQV, NEQ eller MOD IDT: Nr publikationen er identisk med en given publikation. EQV: Nr publikationen teknisk er i overensstemm
7、else med en given publikation, men prsentationen er ndret. NEQ: Nr publikationen teknisk eller prsentationsmssigt ikke er i overensstemmelse med en given standard, men udarbejdet p baggrund af denne. MOD: Nr publikationen er modificeret i forhold til en given publikation. DS/HD 605 S1/A2 Kbenhavn DS
8、 projekt: 39809 ICS: 29.060.20 Deskriptorer: elektrisk kabel,prvning,dimensioner,mekanisk prvning,fysiske prvninger,kemiske prvninger,elektriske prvninger, brandprvninger,klassificering,prvningsbetingelser Frste del af denne publikations betegnelse er: DS/HD, hvilket betyder, at det er en europisk h
9、armoniseringsdokument, der har status som dansk standard Denne publikations overensstemmelse er: IDT med: HD 605 S1:1994/A2:2001 p engelsk HARMONIZATION DOCUMENTHD 605 S1/A2 DOCUMENT DHARMONISATION HARMONISIERUNGSDOKUMENTApril 2001 CENELEC European Committee for Electrotechnical Standardization Comi
10、t Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2001 CENELEC -All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. HD 605 S1:1994/A2:2001 E ICS
11、29.060.20 UDC 621.315.2:620.1 English version Electric cables - Additional test methods Cbles lectriques - Mthodes dessai supplmentaires Elektrokabel - Ergnzende Prfverfahren This amendment A2 modifies the Harmonization Document HD 605 S1:1994; it was approved by CENELEC on 2000-01-01. CENELEC membe
12、rs are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for implementation of this amendment on a national level. Up-to-date lists and bibliographical references concerning such national implementation may be obtained on application to the Central Secretariat
13、or to any CENELEC member. This amendment exists in three official versions (English, French, German). CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,
14、 Portugal, Spain, Sweden, Switzerland and United Kingdom. -,-,- HD 605 S1:1994/A2:2001- 2 - Foreword This amendment to HD 605 S1:1994 has been prepared by WG9 of CENELEC TC20 “Electric Cables”. CENELEC TC 20 confirmed at its Barcelona meeting (May 1998) that the amendment should go to the Unique Acc
15、eptance Procedure. NOTE Since the publication of HD 605 S1 (and A1) a number of changes have been made to other standards to which cross-reference is made in the original texts. In particular: - HD 505 (Parts 1.1 to 1.4 inclusive) has been replaced by EN 60811 (Parts 1-1 to 1-4 inclusive); - HD 405.
16、1 and HD 405.2 have been replaced by EN 50265-2-1 and EN 50265-2-2 respectively; - IEC 502 (4th edition) has been replaced by IEC 60502-1 and IEC 60502-2. In general the updating of these references has not been included in this amendment unless a complete test method has been introduced or replaced
17、. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as amendment A2 to HD 605 S1:1994 on 2000-01-01. The following dates were fixed: -latest date by which the existence of the amendment has to be announced at national level(doa)2000-07-01 -latest date
18、 by which the amendment has to be implemented at national level by publication of a harmonized national standard or by endorsement(dop)2001-10-01 -latest date by which the national standards conflicting with the amendment have to be withdrawn(dow) 2003-01-01 -,-,- - 3 -HD 605 S1:1994/A2:2001 Subclau
19、se 2.1.4.3(a) In the second line, delete: “of this sampling”. Subclause 2.1.10.1 (b) (iii) Delete the existing text and replace as follows, (the figure remains unchanged) : Sporadic irregularities are allowed taking into account the following conditions: Irregularities for which the maximum dimensio
20、n (L) is less than 0,05 mm are not considered; Irregularities for which the maximum dimension (L) is greater than 0,20 mm are not authorised; If irregularities are observed for which the maximum dimension (L) is greater than 0,05 mm but less than or equal to 0,20 mm a second sample, taken close to t
21、he first one, shall be examined and shall not be permitted to show irregularities. Subclause 2.1.12.1 Delete the title and text and insert “Spare”. Subclause 2.2.2 Introduce Method 3 as follows: 2.2.2.3 Method 3 (a)General Three cable samples of 150 mm length each shall be taken from two parts of th
22、e cable, at least 1 m distant from each other. The sheath of the samples shall be cut along the direction of the cable axis and the cores and metallic screens removed. A portion of each sample sheath shall be obtained with two smooth, flat and parallel surfaces, avoiding excessive heating. The thick
23、ness of each portion should be between 1 mm and 2 mm. By means of a die or a sharp knife the test pieces with the dimensions indicated in figure 2.2.2.3 shall be obtained. -,-,- HD 605 S1:1994/A2:2001- 4 - A central longitudinal cut, perpendicular to the width of the test piece, shall be made with a
24、 sharp razor to a point of 4 mm from the wider end. (b)Procedure Test each test piece in the following way. Place the halves of the split end in the jaws of a tensile testing machine and separate the jaws at a rate of (500 5) mm/min. The maximum load needed for the complete tearing of each test piec
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- HD 605 S1 A2 1001
链接地址:https://www.31doc.com/p-3768193.html