GME-12508-2000.pdf
《GME-12508-2000.pdf》由会员分享,可在线阅读,更多相关《GME-12508-2000.pdf(13页珍藏版)》请在三一文库上搜索。
1、STD-OPEL GME L2508-ENGL 2000 8577LLA 0030280 332 Louds rea kers Lautsmecher 1 Introduction 1.1 Scope. All loudspeakers used in the vehicle. Loudspeakers within the meaning of this specifi- cation constitute loudspeaker chassis without sound guidance and loudspeaker boxes. 1.2 Mission / Theme. This s
2、pecification deter- mines the requirements, test conditions and test procedures for the electrical and physical function tests and fatigue tests for loudspeakers used in the vehicle. 1.3 Classification. Not applicable. Note: Nothing in the specification, however, su- persedes applicable laws and reg
3、ulations unless a specific exemption has been obtained. Note: In the event of a conflict between the Ger- man and the English language, the German lan- guage shall take precedence. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 Normative. 1 Einfh
4、rung 1.1 Anwendungsbereich. Alle im Fahrzeug zum Einsatz kommenden Lautsprecher. Als Lautsprecher im Sinne dieser Spezifikation gelten Lautsprecherchassis ohne Schallfhrung und Lautsprecherboxen. 1.2 Aufgabe I Thema. Diese Spezifikation legt die Anforderungen, Prfbedingungen und Prfverfah- ren fr di
5、e elektrischen und physikalischen Funk- tions- und Dauerprfungen fr die im Fahrzeug zum Einsatz kommenden Lautsprecher fest. 1.3 Einteilung. Nicht anwendbar. Hinweis: Falls keine Ausnahmen vereinbart wur- den, darf die Vorschrift keine anzuwendenden Gesetze und Regelungen auer Kraft setzen. Hinweis:
6、 Im Falle von Unstimmigkeiten zwischen dem deutschen und dem englischen Text ist der deutsche Text ausschlaggebend. 2 Referenzen Hinweis: Wenn nicht anders angegeben, ist jeweils die neueste Fassung der angegebenen Referenz gltig. 2.1 Normative. DIN 50014 DIN EN 10204 DIN IEC DIN EN 60268-5 IEC 68-2
7、-30 100/241/CDV-5 IEC 651 VDA 260 IEC 225 2.2 GM. 2.2 GM. GMI 12558 GMI 12590 GMI 60206 GMW3059 ON 1397 ON 1397.1 QMA B+E8370/07 2.3 Additional. None. 2.3 Zustzliche. Keine. 3 Test Preparation and Evalua- tion Auswertung 3 Prfungsvorbereitung und 3.1 Resources. 3.1.1 Calibration. The test facilities
8、 and equip 3.1.1 Kalibrierung. Alle Prfeinrichtungen und ment shall be in good working order and shall -ausrstungen mssen funktionsfhig sein und have a valid calibration label. 3.1 Gerte und Einrichtungen. eine gltige Kalibrierplakette haben. O CopyrigM 2000 General Motors Corporation All Rights Res
9、erved Originating Department: ITDC - Specification Center March 2000 Page 1 of 13 LBSP GME GS 1 05/99 STD-OPEL GME 12508-ENGL 2000 D 577338 0030283 277 D I GME 12508 GM ENGINEERING STANDARD EUROPE I 3.1.2 Alternatives. Aiternative test facilities and equipment may also be used. However, all meas- ur
10、ing variables as specified in this specification shall be determined correctly with respect to its physical definition. 3.1.3 Facilities. In principle, other suitable test facilities are permitted. However, it shall be en- sured that the measurements pertaining to this specification are recorded in
11、the correct manner. 3.1.3.1 Recirculating air temperature cabinet within a temperature range of (-40 .+ 100) “C. - Permissible temperature deviation: i 3.0 “C - Useful volume: 11001 3.1.3.2 Climatic chamber. 3.1.3.3 Electrodynamics vibration generator within a frequency range of (IO . 2000) Hz. 3.1.
12、3.4 Dynamic shock test machine. 3.1.3.5 DC sources s 5 V. 3.1.3.6 Sine-wave noise generator. Test signals: - Sine-wave signals to DIN EN 60268-5 - Broadbandharrow-band noise according to 3.1.3.7 LF amplifier according to DIN EN 60268-5. 3.1.3.8 Microphone amplifier and measuring mi- crophone accordi
13、ng to DIN EN 60268-5. 3.1.3.9 Third-octave filter according to IEC 225. 3.1.3.10 Ohmic resistor suited to the nominal im- pedance of the loudspeaker with an accuracy of f 1 % and a loading capacity of 120 W. DIN EN 60268-5 3.1.3.11 Sound baffle to DIN EN 60268-5. 3.1.3.12 Voltmeter according to IEC
14、651. 3.1.3.13 Frequency analyzer. 3.1.3.14 Acoustic measuring environment ac- cording to DIN EN 60268-5. 3.1.3.15 Fatigue test facility with controls. 3.1.4 Equipment. 3.1.4.1 Scales for determining the total weight. 3.1.2 Alternativen. Es knnen auch alternative Prfeinrichtungen und -ausrstungen ver
15、wendet werden. Alle Messvariablen, wie sie in dieser Vor- schrift angegeben werden, mssen jedoch in Be- zug auf ihre physikalische Definition korrekt fest- gelegt werden. 3.1.3 Einrichtungen. Grundstzlich sind andere geeignete Prfeinrichtungen zulssig. Es muss jedoch gewhrleistet sein, dass die Mess
16、gren im Sinne dieser Spezifikation physikalisch korrekt erfasst werden. 3.1.3.1 Umlufttemperaturschrank mit einem Tem- peraturbereich von (-40 .+ 100) “C. - Zulssige Temperaturabweichung: f 3.0 “C - Nutzraumvolumen: 2 100 I 3.1.3.2 Klimaschrank. 3.1.3.3 Elektrodynamischer Schwingungserreger mit eine
17、m Frequenzbereich von ( I O . 2000) Hz. 3.1.3.4 Dynamische Schockprfmaschine. 3.1.3.5 Gleichstromquelle 2 5 V. 3.1.3.6 Sinus-Rauschgenerator. Prfsignale: - Sinussignale nach DIN EN 60268-5 - Breit-, Schmalbandrauschen nach 3.1.3.7 NF-Verstrker nach DIN EN 60268-5. 3.1.3.8 Mikrofonverstrker und Messm
18、ikrofon nach DIN EN 60268-5. 3.1.3.9 Terzfilter nach IEC 225. 3.1.3.10 Ohmscher Widerstand, den Lautspre- cher-Nennimpedanzen entsprechend mit einer Genauigkeit von f 1 % und einer Belastbarkeit von 1 20 W. 3.1.3.11 Schallwand nach DIN EN 60268-5. 3.1.3.12 Voltmeter nach IEC 651. 3.1.3.13 Frequenzan
19、alysator. 3.1.3.14 Akustische Messumgebung nach 3.1.3.1 5 Dauerprfeinrichtung mit Steuerung, 3.1.4 Ausrstung. 3.1.4.1 Waage zur Ermittlung des Gesamtge- wi chtes. DIN EN 60268-5 DIN EN 60268-5. 8 Copyright 2000 General Motors Corporation All Rights Reserved Page 2 of 13 March 2000 LBSP GME GS G 06B9
20、 -,-,- STDoOPEL GME 1250-ENGL 2000 8597LLB 0030282 LO5 M GM ENGINEERING STANDARD EUROPE GME 12508 3.2 Test Samples. Unless otherwise specified, for the purposes of initial sampling and release test- ing, at least 10 loudspeakers shall be supplied for a laboratory test, as well as additional 5 loud-
21、speakers per installation position for testing ac- cording to paragraph 4.3, accompanied by a test certificate “2.3 according to DIN EN 10204. Ail required Characteristic variable values of the existing test samples are expected to represent the tolerance range of the complete production series. If
22、this prerequisite is not fulfilled, the toler- ance ranges of the complete production series for all required characteristic variables shall be speci- fied in the test certificate, except for the individual values. 3.3 Conditioning. Unless otherwise specified, the tests shall be performed at (+23 1
23、5 ) “C in the as received condition without any special pre- conditioning. 3.4 Documentation. Samples of components or material released to this specification shall be tested for conformity with the requirements of this specification and approved by the responsible GM Department prior to the start o
24、f delivery of produc- tion level components or materials. Any change to the component or material, e.g. design, function, properties, manufacturing proc- ess and/or location of manufacture requires a new release of the product. It is the sole responsibility of the supplier to provide the customer, u
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GME 12508 2000
链接地址:https://www.31doc.com/p-3768300.html