IEC-62137-1-2-2007.pdf
《IEC-62137-1-2-2007.pdf》由会员分享,可在线阅读,更多相关《IEC-62137-1-2-2007.pdf(20页珍藏版)》请在三一文库上搜索。
1、 INTERNATIONAL STANDARD IEC 62137-1-2 First edition 2007-07 Surface mounting technology Environmental and endurance test methods for surface mount solder joint Part 1-2: Shear strength test Reference number IEC 62137-1-2:2007(E) Copyright International Electrotechnical Commission Provided by IHS und
2、er license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 08/07/2007 01:17:22 MDTNo reproduction or networking permitted without license from IHS -,-,- THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All rights reserved. Unless otherwise
3、specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions
4、 about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch A
5、bout the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant rev
6、iew by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. ? Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It
7、 also gives information on projects, withdrawn and replaced publications. ? IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. ? Customer Service Cent
8、re: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 Copyright International Electrotechnical Commission Provided
9、 by IHS under license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 08/07/2007 01:17:22 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD IEC 62137-1-2 First edition 2007-07 Surface mounting technology Environmental and en
10、durance test methods for surface mount solder joint Part 1-2: Shear strength test Q For price, see current catalogue PRICE CODE Commission Electrotechnique Internationale International Electrotechnical Commission Copyright International Electrotechnical Commission Provided by IHS under license with
11、IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 08/07/2007 01:17:22 MDTNo reproduction or networking permitted without license from IHS -,-,- 2 62137-1-2 IEC:2007(E) CONTENTS FOREWORD.3 1 Scope.5 2 Normative references .5 3 Terms and definitions .5 4 General remarks.6 5 Test
12、equipment and materials.7 5.1 Shear test equipment 7 5.2 Pushing tool 7 5.3 Optical microscope7 5.4 Scanning electron microscope (SEM) 7 5.5 Reflow soldering oven .7 5.6 Test substrate .7 5.7 Solder alloy.8 5.8 Solder paste8 6 Mounting method8 7 Test conditions.9 7.1 Test: Rapid change of temperatur
13、e9 7.2 Shear strength test9 8 Test procedure .9 8.1 Test sequence.9 8.2 Pre-conditioning 10 8.3 Initial shear strength10 8.4 Rapid change of temperature 10 8.5 Recovery.10 8.6 Intermediate / final shear strength .10 9 Items to be included in the test report.10 10 Items to be given in the product spe
14、cification .11 Annex A (normative) Shear strength test Details.15 Bibliography17 Figure 1 Area under evaluation in the shear strength test 6 Figure 2 Typical reflow soldering profile.9 Figure 3 Test procedure.10 Figure 4 Failure modes in shear strength test (5-faced electrodes) 12 Figure 5 Failure m
15、odes in shear strength test (two electrodes type).13 Figure 6 Failure modes in shear strength test (switches)14 Figure A.1 Fixing of substrate for shear strength test.16 Figure A.2 Position of pushing tool (leadless components).16 Copyright International Electrotechnical Commission Provided by IHS u
16、nder license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 08/07/2007 01:17:22 MDTNo reproduction or networking permitted without license from IHS -,-,- 62137-1-2 IEC:2007(E) 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SURFACE MOUNTING TECHNOLOGY ENVIRONMENTAL AND EN
17、DURANCE TEST METHODS FOR SURFACE MOUNT SOLDER JOINT Part 1-2: Shear strength test FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to pro
18、mote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides
19、 (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC al
20、so participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as poss
21、ible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. Wh
22、ile all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake
23、 to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to ind
24、icate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents includin
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- IEC 62137 2007
链接地址:https://www.31doc.com/p-3768758.html