GMB-EMS-9309964-1988.pdf
《GMB-EMS-9309964-1988.pdf》由会员分享,可在线阅读,更多相关《GMB-EMS-9309964-1988.pdf(5页珍藏版)》请在三一文库上搜索。
1、STD.GMBRAZIL ENS 73077b9-ENGL 1798 D 7307509 0005bOLi 7b3 W NUMBER: ENGINEERING MATERIAL SPECIFICATION BRASIL PRODUCT ENGINEERING IAME : Jotton cloth tape Fita de tecido de algodo I Description Cotton cloth tape with a polyacrylate base and anti-flame element in top surface, and an acrylic base pres
2、sure sensitive adhesive in the bottom side. This tape is intended for joining PVC coated electrical wiring harness. 2 Requirements 2.1 Color Black. 2.2 Weight 2.2.1 Total According to LTP.PE.124. 300 g/m2 i 20 g/m2. 2.2.2 Adhesive (nominal) I 15 g/m2 f IO g/m2. 2.3 Thickness According to LTP.Al .093
3、. 1 Descrio Fita de tecido de algodo com elemento base de poliacrilato e anti-chama na face superior, e um adesivo sensvel presso de base acrlica no lado inferior. Esta fita destinada para junes de chicote eltrico coberto com PVC. 2 Requisitos 2.1 Cor Preta. 2.2 Peso 2.2.1 Total Conforme LTP.PE.124.
4、 300 g/m2 k 20 g/m2. 2.2.2 Adesivo (nominal) 115g/m2$110g/m2. 2.3 Espessura Conforme LTP.Ai.093. - APPROVED BY: L.L. CERLINI NETO REVISION : 02/98 STD-GMBRAZIL EMS 73077b4-ENGL L798 P 7307509 0005b05 BTT H - PAGE: 2 of 5 EMS.9309964 0.30 mm k 0.02 mrn. 0,30 mm k 0,02 mm. 2.4 Tensile strength 2.4 Res
5、istncia trao . 350 kgf/cm2 min 350 kgf/cm2 min According to ASTM D 412, method A, Conforme ASTM D 412, mtodo A, die C and crosshead speed of molde C e velocidade de arrancamento 100 mm/min. 100 mm/min. 2.5 Peel adhesion strength 2.5 Resistncia adesiva 300 gficm min. Apply the sample onto a painted s
6、urface according to the EMS.Tl.0244 baselvarnish painting system (see figure I) using a roller with 2000 grams for each centimeter of the tape width, two times in each direction at a velocrty of approximately 1 O mm/s. After this preparation the sample shall be submitted during 24 hours at 23“C$r2“C
7、 prior to peel adhesion test and environmental conditioning according to item 2.6 Peel adhesion test shall be performed at a velocity of 200 mm/minute. 300 gfkm min. Aplicar uma amostra em um painel com superficie pintada conforme EMS.Tl.0244 sistema de pintura basehemiz (veja figura I) usando um ro
8、lo com 2000 gramas para cada centmetro da largura da fita, duas vezes em cada direo a uma velocidade aproximada de 1 O mm/s. Aps esta preparao a amostra deve ser submetidadurante 24 horas 23C k 2C antes do teste de resistncia adesiva e dos condicionamentos ambientais de acordo com o item 2.6. O test
9、e de resistncia adesiva deve ser realizado a uma velocidade de 200 mm/minuto. 2.6 Resistance to environmental 2.6 Resistncia aos condicionamentos conditioning ambientais The specimens prepared according to item 2.5 shall be exposed to the conditionings listed below. Material shall not present more t
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GMB EMS 9309964 1988
链接地址:https://www.31doc.com/p-3769239.html