IEEE-292-1969-R2005.pdf
《IEEE-292-1969-R2005.pdf》由会员分享,可在线阅读,更多相关《IEEE-292-1969-R2005.pdf(29页珍藏版)》请在三一文库上搜索。
1、 IEEE Std 292-1969 IEEE Specifi cation Format for Single- Degree-of-Freedom Spring-Restrained Rate Gyros Reaffirmed September 24, 1992 IEEE Standards Board Reaffirmed February 23, 1993 American National Standards Institute Copyright 1969 by The Institute of Electrical and Electronics Engineers, Inc.
2、 No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/11111
3、11001, User=Japan, IHS Not for Resale, 07/30/2008 03:24:11 MDTNo reproduction or networking permitted without license from IHS -,-,- ii Acknowledgment The Institute wishes to acknowledge its indebtedness to those who have so freely given of their time and knowledge and have conducted experimental wo
4、rk on which many of the IEEE publications are based. This Specifi cation Format and the Test Procedure for Single-Degree-of-Freedom Spring-Restrained Rate Gyros (IEEE Standards Publication No. 293) represent a group effort on a large scale. They were generated as projects of the Gyro and Acceleromet
5、er Panel from May of 1962 to November of 1967. The Gyro and Accelerometer Panel (GAP) affi liated with the IEEE in May of 1965 and is now a part of the IEEE Aerospace and Electronic Systems Group. A total of 238 individuals attended 30 GAP meetings while these documents were in preparation. Fifty-on
6、e individuals attended six meetings or more and provided 61 percent of the total attendance of 916. These people are listed here. K. L. Bachman W. E. Bachman R. Broderson J. T. Bull A. T. Campbell, (GAP Chair, 1965) J. R. Cash P. B. Clark, (GAP Chair, 1967) V. B. Corey R. A. Crawford H. A. Dinter K.
7、 E. Eggers B. H. Evans H. L. Ferger W. H. Ficken T. A. Fuhrman G. A. Glaubitz J. M. Golden R. Goodstein, (GAP Chair, 1962, 1963) K. N. Green J. G. Hawkins Capt. F. J. Hellings E. Hitscherich J. A. Hogg, (GAP Chair, 1963, 1964) L. K. Jensen J. V. Johnston H. Kehm J. P. Kochan A. M. Leeking, (GAP Chai
8、r, 1966) R. E. Levy J. L. Luber J. W. Maier R. H. Marcus F. B. Mikoleit M. D. Mobley C. F. Morley G. H. Neugebauer T. M. Rankin H. Rogall G. Schuetzmann N. F. Sinnott H. E. Soland G. T. Starks C. Strang E. L. Swainson C. O. Swanson, (GAP Chair, 1968) C. I. Thornburg R. S. Vaughn J. Volk L. F. Warnoc
9、k W. M. Weil A. E. Willis Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 03:24:11 MDTNo reproduction or networking permitted without license from IHS -,-,- iii
10、Introduction This Specifi cation Format has been prepared as a guide for the preparation of a single-degree-of-freedom spring- restrained rate gyro specifi cation. Prepared by the Gyro and Accelerometer Panel of the Aerospace Electronic Systems Group of the Institute of Electrical and Electronics En
11、gineers, this format provides a common meeting ground of terminology and practice for manufacturers and users. Two other documents, Aerospace Industries Association EETC Report No. 5 (Revision A), “Standard Gyro Terminology,”* and IEEE Standards Publication No. 293, “Test Procedure for Single-Degree
12、-of-Freedom Spring- Restrained Rate Gyros,” have been utilized in the preparation of this format. This format will be limited to conventional single-degree-of-freedom spring-restrained rate gyros. A model equation is given in paragraph 6.3 for reference, and is to be included in a specifi cation onl
13、y to the extent necessary. Table 1, on this page, lists various rate gyro design features for which this format is applicable. The table is not intended to make any suggestion regarding the selection of particular design features that might restrict the free choice of manufacturers. Blank spaces are
14、 provided in the Specifi cation Format for the insertion of specifi c values. Brackets are used to designate possible alternates. Boxed information is intended for explanatory purposes. Figures 1, 2, and 3 are to be used as a guide for the preparation of specifi c fi gures or drawings. The user is c
15、autioned not to overspecify. Only those parameters that are required to guarantee proper instrument performance in the intended usage should be controlled. * Available from: National Standards Association, Inc. 1321 Fourteenth Street N.W. Washington. D.C. 20005 Table 1Rate Gyro Design Features Picko
16、ffSpin Motor Damping RegulationSelf-Test Torquer Rotor Rotation Detector 1. Variable reluctance (microsyn) 1. Ac synchronous hysteresis (3- phase, 2-phase) 1. Self- compensating 1. Variable reluctance1. Pulse 2. Potentiometer2. Ac induction (squirrel cage rotor) (3-phase, 2-phase) 2. Controlled temp
17、erature (heater controlled) 2. Dc permanent magnet2. Near sinusoidal 3. Switch3. Dc (with governor)3. Uncompensated 4. Other (optical, capacitance) NOTE The intent of this table is to indicate confi gurations of a spring-restrained rate gyro for which this specifi cation format is applicable. The fe
18、atures may be employed in any combination. Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 03:24:11 MDTNo reproduction or networking permitted without license fr
19、om IHS -,-,- iv SPECIFICATION COVER SHEET RATE GYRO, _ DEGREES PER SECOND Specifi cation No. _ Date Procuring Firm or Organization Data Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/1111111001, User=Japan, IHS Not
20、for Resale, 07/30/2008 03:24:11 MDTNo reproduction or networking permitted without license from IHS -,-,- v CLAUSEPAGE 1. Scope.1 2. Applicable Documents1 2.1 Specifications. 1 2.2 Standards 1 2.3 Drawings 2 2.4 Bulletins. 2 2.5 Other Publications 2 3. Requirements 2 3.1 Description. 2 3.2 General R
21、equirements 2 3.3 Performance. 3 3.4 Mechanical. 7 3.5 Electrical 8 3.6 Environmental 10 3.7 Reliability. 13 4. Quality Assurance Provisions.13 4.1 Classification of Tests 13 4.2 Acceptance Tests 13 4.3 Qualification Tests. 15 4.4 Reliability Tests . 16 4.5 Test Conditions and Equipment. 17 4.6 Test
22、 Methods 17 4.7 Test Data Submittal 19 5. Preparation For Delivery.19 6. Notes .19 6.1 Intended Use 19 6.2 Ordering Data. 20 6.3 Model Equation 20 Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/1111111001, User=Japa
23、n, IHS Not for Resale, 07/30/2008 03:24:11 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- IEEE 292 1969 R2005
链接地址:https://www.31doc.com/p-3769317.html