GMNA-GMP.TES.004-2004.pdf
《GMNA-GMP.TES.004-2004.pdf》由会员分享,可在线阅读,更多相关《GMNA-GMP.TES.004-2004.pdf(3页珍藏版)》请在三一文库上搜索。
1、 ENGINEERING STANDARDS Material Specification Plastics GMP.TES.004 Thermoplastic Elastomer - Styrene Block Copolymer, Shore A73, Interior, UV Stabilized, Integrally Colored 1 Scope This specification covers the properties of a natural or integrally colored, UV stabilized ther- moplastic elastomer co
2、nsisting of polypropylene and SEBS (styrene/ethylene/butylene/styrene) rubber for interior applications. 1.1 Typical Application. Typical applications include the following: lever knobs, buttons and other soft touch applications. Continuous operat- ing temperature range: -40 to 135 C. 2 References N
3、ote: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. ISO 34-1 ISO 868 ISO 37 ISO 1183 ISO 812 SAE J1885 ISO 815 SAE J2236 2.2 GM Standards/Specifications. GM9305P GMW3059 GMW3001 GMW3221 3 Requirements 3.1 Requirements on Delivery.
4、 Important physical, mechanical and thermal properties that characterize the material are summarized in charts. The color shall be specified on drawings, in material specifications and otherwise. Requirements on Test Specimens Tests shall be conducted using the latest issue of the test methods indic
5、ated. Suitable precauti- ons should be taken to ensure that applicable safe limits are not exceeded when conducting test procedures, processes, and/or handling the materials required by this specification. Test specimens shall be die cut from fan gated injection molded plaques having a nominal thick
6、- ness of 2.0 0.2 mm. Die cut specimens are to be tested with the long axis of the test specimen perpendicular to the direction of flow. Plaque dimensions must be sufficient to permit this. Tests shall be conducted 40 h minimum after molding and immediately following a condition- ing period of 24 h
7、per GMW3221 Code A, unless otherwise specified. All tests shall be performed on unannealed specimens. In addi- tion, tests specified at temperatures below or above 22 3C shall be conducted at the speci- fied temperature using specimens conditioned at the specified temperature for 4 h minimum. The mi
8、nimum values specified in the property tables must be met by test specimens in natural, black, or in a standard sampled color if natural or black are not available. For colored grades where other pigment and additive systems (e.g. stabilizer) are used, the impact values shall not decrease more than
9、10% from the specified minimum value. Copyright 2004 General Motors Corporation All Rights Reserved June 2004 Originating Department: North American Engineering Standards Page 1 of 3 Copyright General Motors North America Provided by IHS under license with GM Licensee=IHS Employees/1111111001, User=
10、Japan, IHS Not for Resale, 06/23/2008 23:30:36 MDTNo reproduction or networking permitted without license from IHS -,-,- GMP.TES.004 GM ENGINEERING STANDARDS Copyright 2004 General Motors Corporation All Rights Reserved Page 2 of 3 June 2004 3.1.1 Mechanical Requirements. See Table 1. Table 1: Mecha
11、nical Requirements Mechanical Properties Test Methods Unit Values Hardness - Shore A ISO 868, 15 s delay Shore A 73 7 Tensile Stress at break ISO 37, Type 1 dumbbell, 500 mm/minute MPa 6.9 min Elongation at Break ISO 37, Type 1 dumbbell, 500 mm/minute % 460 min Tensile Stress at 100 % Elongation ISO
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GMNA GMP TES 004 2004
链接地址:https://www.31doc.com/p-3769490.html