IEEE-1431-2004.pdf
《IEEE-1431-2004.pdf》由会员分享,可在线阅读,更多相关《IEEE-1431-2004.pdf(79页珍藏版)》请在三一文库上搜索。
1、IEEE Std 1431-2004 IEEE Standards 1431 TM IEEE Standard Specification Format Guide and Test Procedure for Coriolis Vibratory Gyros 3 Park Avenue, New York, NY 10016-5997, USA IEEE Aerospace and Electronic Systems Society Sponsored by the Gyro and Accelerometer Panel IEEE Standards 20 December 2004 P
2、rint: SH95224 PDF: SS95224 Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 12:02:31 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyrig
3、ht The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 12:02:31 MDTNo reproduction or networking permitted without license from IHS -,-,- Recognized as an American National Standa
4、rd (ANSI) The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2004 by the Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 20 December 2004. Printed in the United States of America. IEEE is a register
5、ed trademark in the U.S. Patent +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. NOTEAttention is called to the possibility that implementation of this standard may require use of s
6、ubject matter covered by patent rights. By publication of this standard, no position is taken with respect to the exist- ence or validity of any patent rights in connection therewith. The IEEE shall not be responsible for identifying patents for which a license may be required by an IEEE standard or
7、 for conducting inquiries into the legal valid- ity or scope of those patents that are brought to its attention. Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 12:0
8、2:31 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright 2004 IEEE. All rights reserved.iii Introduction This new standard consists of two parts: Part I is a specification format guide for the preparation of a Coriolis vibratory gyro specification. It provides a commo
9、n meeting ground of terminology and practice for manufacturers and users. The user is cautioned not to over specify; only those parameters that are required to guarantee proper performance in the specific application should be controlled. In general, the specification should contain only those requi
10、rements that can be verified by test or inspection. Parameters in addition to those given in this standard are not precluded. Part II is a compilation of recommended procedures for testing a Coriolis vibratory gyro. These procedures, including test conditions to be considered, are derived from those
11、 currently in use. For a specific application, the test procedure should reflect the requirements of the specification; therefore, not all tests outlined in this standard need be included, nor are additional tests precluded. In some cases, alternative methods for measur- ing performance characterist
12、ics have been included or indicated. The intent is for the specification writer to extract the applicable test conditions and equipment requirements from clause 11 for inclusion in the appropriate clauses listed under 6.5 of this standard. Similarly, it is intended that the writer extract the applic
13、able test procedures from clause 12 for inclusion in the appropriate clauses listed under 6.6. Part II can also be used as a guide in the preparation of a separate Coriolis vibratory gyro test specification with appropriate clause numbering. In general, the intent is for the specification writer to
14、ensure consistency and traceability between Part II test procedures and Part I requirements for perfor- mance, mechanical, electrical, environmental, reliability, and quality assurance. To that end, a test procedure should not be listed in Part II unless a related requirement exists in Part I. Blank
15、 spaces in the text of this document permit the specification writer to insert specific information such as parameter values and their tolerances, clause numbers, etc. Brackets are used to enclose alternative choices of dimensional units, signs, axes, etc. Boxed statements are included for informati
16、on only and are not part of the specification or test procedures. The terminology used conforms to The Authoritative Dictionary of IEEE Standards Terms, Seventh Edition. The units used conform to ANSI/IEEE Std 268- 1992, IEEE Standard for Metric Practice. The abbreviation of units conforms to ANSI/I
17、EEE Std 260.1- 1993, Standard Letter Symbols for Units of Measurement. The graphic symbols used conform to ANSI/ IEEE Std 315-1975, IEEE Standard Graphic Symbols for Electrical and Electronics Diagrams and its supplement ANSI/IEEE Std 315A-1986. This standard defines the requirements and test proced
18、ures for a Coriolis vibratory gyro in terms unique to the Coriolis vibratory gyro. The requirements contained herein cover applications where the Coriolis vibra- tory gyro is used as an angular motion sensor in navigation and control systems. The term Coriolis vibratory gyro is accepted to include t
19、he electronics necessary to operate the gyro and to condition the output signal. The Coriolis vibratory gyro provides an output proportional to inertial angular rate about its input axis. Annex A lists various Coriolis vibratory gyro design features for which this format is applicable. The list is n
20、ot intended to make any suggestion regarding the selection of particular design features that might restrict the free choice of manufacturers. Annex B is a description of the various types of Coriolis vibratory gyros and their functioning. This introduction is not part of IEEE Std 1431-2004, IEEE St
21、andard Specification Format Guide and Test Procedure for Coriolis Vibratory Gyros. Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 12:02:31 MDTNo reproduction or net
22、working permitted without license from IHS -,-,- ivCopyright 2004 IEEE. All rights reserved. Annex C is a compliance matrix that lists requirements clauses and their corresponding test clauses. Notice to users Errata Errata, if any, for this and all other standards can be accessed at the following U
23、RL: http:/ standards.ieee.org/reading/ieee/updates/errata/index.html. Users are encouraged to check this URL for errata periodically. Interpretations Current interpretations can be accessed at the following URL: http:/standards.ieee.org/reading/ieee/interp/ index.html. Patents Attention is called to
24、 the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken with respect to the existence or validity of any patent rights in connection therewith. The IEEE shall not be responsible for identi
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- IEEE 1431 2004
链接地址:https://www.31doc.com/p-3769602.html