《IEC-61169-4-2008.pdf》由会员分享,可在线阅读,更多相关《IEC-61169-4-2008.pdf(28页珍藏版)》请在三一文库上搜索。
1、 IEC 61169-4 Edition 1.0 2008-04 INTERNATIONAL STANDARD Radio-frequency connectors Part 4: RF coaxial connectors with inner diameter of outer conductor 16 mm (0,63 in) with screw lock Characteristic impedance 50 (type 7-16) IEC 61169-4:2008(E) Copyright International Electrotechnical Commission Prov
2、ided by IHS under license with IECLicensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 02:16:23 MDTNo reproduction or networking permitted without license from IHS -,-,- THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specifie
3、d, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about I
4、EC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the
5、 IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by t
6、he IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. ? Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gi
7、ves information on projects, withdrawn and replaced publications. ? IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. ? Electropedia: www.electropedi
8、a.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. ? Customer Service Centre: www.iec
9、.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 Copyright International Electrotechnical Commission Provided by IHS und
10、er license with IECLicensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 02:16:23 MDTNo reproduction or networking permitted without license from IHS -,-,- IEC 61169-4 Edition 1.0 2008-04 INTERNATIONAL STANDARD Radio-frequency connectors Part 4: RF coaxial connectors with inner diameter of outer
11、conductor 16 mm (0,63 in) with screw lock Characteristic impedance 50 (type 7-16) INTERNATIONAL ELECTROTECHNICAL COMMISSION T ICS 29.120.10 PRICE CODE ISBN 2-8318-9725-4 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=Boeing Co/5910770001 Not for Re
12、sale, 07/25/2008 02:16:23 MDTNo reproduction or networking permitted without license from IHS -,-,- 2 61169-4 IEC:2008(E) CONTENTS FOREWORD.4 1 Scope.6 2 Normative references .6 3 Mating face and gauge information.6 3.1 Dimensions General connectors Grade 27 3.1.1 Connector with pin centre contact7
13、3.1.2 Connector with socket centre contact 8 3.2 Gauges for general purpose connectors - Grade 2 9 3.2.1 Gauges for connector with socket centre contact.9 3.3 Dimensions standard test connectors Grade 0.10 3.3.1 Standard test connector with pin centre contact.10 3.3.2 Standard test connector with so
14、cket centre contact .10 4 Quality assessment procedures11 4.1 General.11 4.2 Ratings and characteristics .11 4.3 Test Schedule and Inspection requirements 14 4.3.1 Acceptance tests .14 4.3.2 Periodic tests 15 4.4 Procedures16 4.4.1 Quality conformance inspection.16 4.4.2 Qualification approval and i
15、ts maintenance16 5 Instructions for preparation of detail specifications .17 5.1 General.17 5.2 Identification of the Detail specification .17 5.3 Identification of the component17 5.4 Performance17 5.5 Marking, ordering information and related matters.18 5.6 Selection of tests, test conditions and
16、severities18 5.7 Blank detail specification pro-forma for type 7-16 connector19 Figure 1 Connector with pin centre contact 7 Figure 2 Connector with socket centre contact.8 Figure 3 Gauge pin for socket centre contact.9 Figure 4 Gauge ring for socket outer contact9 Figure 5 Slotted centre contact 11
17、 Table 1 Connector with pin centre contact. 7 Table 2 Connector with socket centre contact 8 Table 3 Tolerance for the standard connector with pin centre contact. .10 Table 4 Tolerance for the standard connector with socket centre contact.10 Table 5 Slotted centre contact .11 Table 6 Preferred clima
18、tic categories (see IEC 60068-1):.12 Table 7 Ratings and characteristics .13 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 02:16:23 MDTNo reproduction or networking permitted without license from IHS
19、 -,-,- 61169-4 IEC:2008(E) 3 Table 8 Acceptance tests.14 Table 9 Periodic tests 15 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 02:16:23 MDTNo reproduction or networking permitted without license fr
20、om IHS -,-,- 4 61169-4 IEC:2008(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RADIO-FREQUENCY CONNECTORS Part 4: RF coaxial connectors with inner diameter of outer conductor 16 mm (0,63 in) with screw lock Characteristic impedance 50 (type 7-16) FOREWORD 1) The International Electrotechnical Commis
21、sion (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in
22、 addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee in
23、terested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordanc
24、e with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interes
25、ted IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsibl
26、e for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence bet
27、ween any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All us
28、ers should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or ot
29、her damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication.
30、 Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such pate
31、nt rights. International Standard IEC 61169-4 has been prepared by subcommittee 46F: RF and microwave passive components, of IEC technical committee 46: Cables, wires, waveguides, r.f. connectors, r.f. and microwave passive components and accessories. This standard cancels and replaces IEC/PAS 61169
32、-4 published in 2006. This first edition constitutes a technical revision. The text of this standard is based on the following documents: FDIS Report on voting 46F/60/FDIS 46F/71/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in th
33、e above table. Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 02:16:23 MDTNo reproduction or networking permitted without license from IHS -,-,- 61169-4 IEC:2008(E) 5 This publication has been drafted
34、 in accordance with the ISO/IEC Directives, Part 2. A list of all parts of IEC 61169 series, published under the general title Radio-frequency connectors, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance resu
35、lt date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. Copyrig
36、ht International Electrotechnical Commission Provided by IHS under license with IECLicensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 02:16:23 MDTNo reproduction or networking permitted without license from IHS -,-,- 6 61169-4 IEC:2008(E) RADIO-FREQUENCY CONNECTORS Part 4: RF coaxial connector
37、s with inner diameter of outer conductor 16 mm (0,63 in) with screw lock Characteristic impedance 50 (type 7-16) 1 Scope This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for type 7-16 R.F. coaxial connec
38、tors with screw lock. The connectors are normally used with 50 flexible and semi-rigid r.f. cables for middle power applications in an operating frequency range up to 7,5 GHz. It describes the interface dimensions for general purpose grade 2 connectors, dimensional details for standard test connecto
39、rs, grade 0, together with gauging information and the mandatory tests selected from QC 22000 (IEC 61169-1), applicable to all DS relating to type 7-16 connectors. This specification indicates the recommended performance characteristics to be considered when writing a DS and covers test schedules an
40、d inspection requirements. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
41、 IEC 61169-1, Radio-frequency connectors Part 1: Generic specification General requirements and measuring methods IEC 62037, RF connectors, connector cable assemblies, and cables - Intermodulation level measurement 3 Mating face and gauge information Metric dimension are original dimensions. All und
42、imensioned pictorial configurations are for reference purpose only. Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 02:16:23 MDTNo reproduction or networking permitted without license from IHS -,-,- 61
43、169-4 IEC:2008(E) 7 3.1 Dimensions General connectors Grade 2 3.1.1 Connector with pin centre contact a b c d f e m l g h i Note 3 IEC 540/08 NOTE For dimensions see Table 1. Figure 1 Connector with pin centre contact Table 1 Connector with pin centre contact Reference Millimetres Inches Notes Minim
44、um Maximum Minimum Maximum a M291,5 M291,5 2 b 20,6 21,4 0,811 0,843 c 18,03 18,21 0,7098 0,7169 d 4,96 5,04 0,1953 0,1984 e 15,85 16,25 0,6240 0,6398 f 7 (nominal) 0,276 (nominal) 1 g 1,4 1,6 0,0551 0,0630 h 1,47 1,77 0,0579 0,0697 i 7,00 8,00 0,276 0,315 l - 4,5 - 0,177 m 7,00 9,00 0,276 0,354 NOT
45、E 1 The tolerance on this dimension is determined by the tolerance of characteristic impedance. NOTE 2 M291,5 indicates metric screw thread with nominal diameter 29 mm(1,141 in) and pitch 1,5 mm(0,059 in). NOTE 3 Mechanical and electrical reference plane (see Figure 1). Copyright International Elect
46、rotechnical Commission Provided by IHS under license with IECLicensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 02:16:23 MDTNo reproduction or networking permitted without license from IHS -,-,- 8 61169-4 IEC:2008(E) 3.1.2 Connector with socket centre contact f k Note 4 Note 2 Note 5 s p q r e
47、 t n a IEC 541/08 NOTE For dimensions see Table 2. Figure 2 Connector with socket centre contact Table 2 Connector with socket centre contact Reference Millimetres Inches Note Minimum Maximum Minimum Maximum a M291,5 M291,5 3 e 15,85 16,25 0,6240 0,6398 f 7(nominal) 0,276(nominal) 1 k 10 - 0,394 - n 22,1 22,9 0,870 0,902 p 0,5 0,7 0,0197 0,0276 q 1,77 2,07 0,0697 0,0815 r 5 - 0,197 - s 8,1 - 0,319 - t 17,84 18,02 0,7024 0,7094 2 NOTE 1 The tolerances on this dimensions is determined by the tolerance of characteristic impedance. NOTE 2 Standard is a non-slotted outer contact. If a
链接地址:https://www.31doc.com/p-3769830.html