《BS-5173-101.2-1987.pdf》由会员分享,可在线阅读,更多相关《BS-5173-101.2-1987.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS 5173-101.2: 1987 Methods of test for rubber and plastics hoses and hose assemblies Part 101: Determination of dimensions Section 101.2 Measurement of length of hoses and hose assemblies UDC 621.643.33-036:620.1 Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:31:13 GMT+0
2、0:00 2006, Uncontrolled Copy, (c) BSI BS 5173-101.2:1987 This British Standard, having been prepared under the direction of the Rubber Standards Committee, was published under the authority of the Board of BSI and comes into effect on 30 April 1987 BSI 04-1999 First published in BS 5173-1, February
3、1976 First revision as BS 5173-101.2, April 1987 The following BSI references relate to the work on this standard: Committee reference RUM/9 Draft for comment 85/43622 DC ISBN 0 580 15827 6 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the
4、 Rubber Standards Committee (RUM/-) to Technical Committee RUM/9, upon which the following bodies were represented: Association of Metropolitan Authorities British Coal British Compressed Gases Association British Gas plc British Railways Board British Rubber Manufacturers Association Chief and Assi
5、stant Chief Fire Officers Association Department of the Environment (Property Services Agency) Fire Extinguishing Trades Association Health and Safety Executive Home Office Institution of Fire Engineers Institution of Production Engineers Liquefied Petroleum Gas Industry Technical Association (UK) L
6、ondon Regional Transport Malaysian Rubber Producers Research Association Ministry of Defence Society of Motor Manufacturers and Traders Limited Water Authorities Association The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Association of H
7、ydraulic Equipment Manufacturers British Plastics Federation Energy Industries Council Engineering Equipment and Materials Users Association Petrol Pump Manufacturers Association United Kingdom Petroleum Industry Association Ltd. Amendments issued since publication Amd. No.Date of issueComments Lice
8、nsed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:31:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5173-101.2:1987 BSI 04-1999i Contents Page Committees responsibleInside front cover Forewordii 1Scope1 2Measurement of length1 3Identification of length1 4Test report1 Figure 1 Length of exposed
9、 hose between fittings1 Figure 2 Length over nipples1 Figure 3 Length from centre line of angle (90)2 Figure 4 Length from centre line of nipple (135 angle)2 Figure 5 Length over male union3 Figure 6 Length from centre line of banjo coupling3 Publications referred toInside back cover Licensed Copy:
10、sheffieldun sheffieldun, na, Fri Dec 01 14:31:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5173-101.2:1987 ii BSI 04-1999 Foreword This Section of BS 5173 has been prepared under the direction of the Rubber Standards Committee. It supersedes clause 9 of BS 5173-1:1976 and, together with Section
11、101.1, supersedes the whole of BS 5173-1:1976 which is withdrawn. The remainder of the 1976 and 1977 editions are to be revised and as each of the tests is revised it is intended to issue it as a separate Part or Section of BS 5173, as described in BS 5173-100. Section 101.1 is identical with ISO 46
12、71-1984 published by the International Organization for Standardization (ISO). ISO 4671 does not include a clause dealing with the measurement of length and this Section of BS 5173 enlarges clause 9 of BS 5173-1:1976 to include illustrated examples of hose assembly length measurements. A British Sta
13、ndard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover
14、, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun,
15、 na, Fri Dec 01 14:31:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5173-101.2:1987 BSI 04-19991 1 Scope This Section of BS 5173 describes methods of measuring the length of hoses and provides an identifying measurement for the length of hose assemblies. NOTEThe titles of the publications referre
16、d to in this standard are listed on the inside back page. 2 Measurement of length For lengths up to and including 20 m, measure with a graduated steel tape complying with BS 4484-1. For lengths over 20 m, measure with a graduated steel tape complying with BS 4484-1 or a wheel type measuring gauge. M
17、ake all measurements with the hose in a straight and unstretched condition. 3 Identification of length 3.1 For hoses without end fittings determine the length of the hose between the extreme ends of the cut length. 3.2 For hoses with end fittings attached ensure that the measuring points for the len
18、gth of the assembly are identified. NOTEFigure 1, Figure 2, Figure 3, Figure 4, Figure 5 and Figure 6 show typical end fittings and how to identify the different measuring points. 3.3 For hose assemblies with end fittings not illustrated in Figure 1 to Figure 6 ensure that the measuring point of the
19、 fitting is identified from the fitting manufacturers published data. 4 Test report The test report shall include the following information: a) a full description of the hose or hose assembly; b) the date of test; c) the number and Section of this British Standard i.e. BS 5173-101.2; d) the length o
20、f the hose or hose assembly; e) the points of measurement; f) the method of measurement. Figure 1 Length of exposed hose between fittings Figure 2 Length over nipples Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:31:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5173-101.2:1987 2 BSI 0
21、4-1999 Figure 3 Length from centre line of angle (90) Figure 4 Length from centre line of nipple (135 angle) Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:31:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5173-101.2:1987 BSI 04-19993 Figure 5 Length over male union Figure 6 Length from
22、 centre line of banjo coupling Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:31:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 4 blank Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:31:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5173-101.2:1987 BSI 04-1999 Publications ref
23、erred to BS 4484, Measuring instruments for constructional works. BS 4484-1, Metric graduation and figuring of instruments for linear measurement. BS 5173, Methods of test for rubber and plastics hoses and hose assemblies1). BS 5173-101.1, Measurement of dimensions (excluding length). ISO 4671, Rubb
24、er and plastics hose and hose assemblies Methods of measurement of dimensions1). 1) Referred to in the foreword only. Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:31:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5173-101.2: 1987 BSI 389 Chiswick High Road London W4 4AL BSI British St
25、andards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British
26、 Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the te
27、chnical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards O
28、rders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Stan
29、dards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on
30、 all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Mem
31、bership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no ext
32、ract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as sy
33、mbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:31:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI
链接地址:https://www.31doc.com/p-3769998.html