IEC-PAS-61755-3-32-2007.pdf
《IEC-PAS-61755-3-32-2007.pdf》由会员分享,可在线阅读,更多相关《IEC-PAS-61755-3-32-2007.pdf(16页珍藏版)》请在三一文库上搜索。
1、 IEC/PAS 61755-3-32 Edition 1.0 2007-10 PUBLICLY AVAILABLE SPECIFICATION PRE-STANDARD Fibre optic connector optical interfaces Part 3-32: Optical interface 8 degrees angled-PC end-face thermoset rectangular ferrule, single mode fibres IEC/PAS 61755-3-32:2007(E) Copyright International Electrotechnic
2、al Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 10/17/2007 03:37:42 MDTNo reproduction or networking permitted without license from IHS -,-,- THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All r
3、ights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the req
4、uester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Emai
5、l: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC public
6、ations is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. ? Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number
7、, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. ? IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also
8、by email. ? Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary o
9、nline. ? Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 Copyright International Electr
10、otechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 10/17/2007 03:37:42 MDTNo reproduction or networking permitted without license from IHS -,-,- IEC/PAS 61755-3-32 Edition 1.0 2007-10 PUBLICLY AVAILABLE SPECIFICATION PRE-S
11、TANDARD Fibre optic connector optical interfaces Part 3-32: Optical interface 8 degrees angled-PC end-face thermoset rectangular ferrule, single mode fibres INTERNATIONAL ELECTROTECHNICAL COMMISSION M ICS 33.180.20 PRICE CODE ISBN 2-8318-9329-1 Copyright International Electrotechnical Commission Pro
12、vided by IHS under license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 10/17/2007 03:37:42 MDTNo reproduction or networking permitted without license from IHS -,-,- 2 PAS 61755-3-32 IEC:2007(E) CONTENTS FOREWORD.3 1 Scope.5 2 Normative references5 3 Description .5 4
13、Optical interface parameters.6 4.1 End-face parameters related to attenuation6 4.2 End-face parameters related to physical contact 11 Figure 1 Fibre core lateral location .6 Figure 2 Alignment pin .8 Figure 3 End-face parameters related to attenuation.8 Figure 4 End-face geometry parameters related
14、to physical contact 11 Table 1 Optical interface parameter values related to attenuation for 4,4 mm x 2,5 mm rectangular ferrules with two fibres fixed9 Table 2 Optical interface parameter values related to attenuation for 4,4 mm 2,5 mm rectangular ferrules with four, eight, ten and twelve fibres fi
15、xed .9 Table 3 Optical interface parameter values related to attenuation for 6,4 mm 2,5 mm rectangular ferrules with two fibres fixed10 Table 4 Optical interface parameter values related to attenuation for 6,4 mm 2,5 mm rectangular ferrules with four, eight, ten and twelve fibres fixed .10 Table 5 E
16、nd-face geometry parameters related to physical contact .12 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 10/17/2007 03:37:42 MDTNo reproduction or networking permitted without license fr
17、om IHS -,-,- PAS 61755-3-32 IEC:2007(E) 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC CONNECTOR OPTICAL INTERFACES Part 3-32: Optical interface 8 degrees angled-PC end-face thermoset rectangular ferrule, single mode fibres FOREWORD 1) The International Electrotechnical Commission (IEC) i
18、s a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to
19、 other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in
20、the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with condi
21、tions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC Nati
22、onal Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the wa
23、y in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC
24、 Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should e
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- IEC PAS 61755 32 2007
链接地址:https://www.31doc.com/p-3770349.html