IEEE-1018-2004.pdf
《IEEE-1018-2004.pdf》由会员分享,可在线阅读,更多相关《IEEE-1018-2004.pdf(38页珍藏版)》请在三一文库上搜索。
1、IEEE Std 1018-2004 (Revision of IEEE Std 1018-1991) IEEE Standards 1018 TM IEEE Recommended Practice for Specifying Electric Submersible Pump CableEthylene-Propylene Rubber Insulation 3 Park Avenue, New York, NY 10016-5997, USA IEEE Industry Applications Society Sponsored by the Petroleum and Chemic
2、al Industry Committee IEEE Standards 13 April 2005 Print: SH95251 PDF: SS95251 Recognized as an American National Standard (ANSI) The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2005 by the Institute of Electrical and Electronics Engi
3、neers, Inc. All rights reserved. Published 13 April 2005. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright C
4、learance Center. NOTE-Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken with respect to the existence or validity of any patent rights in connection therewith.
5、The IEEE shall not be responsible for identifying patents for which a license may be required by an IEEE standard or for conducting inquiries into the legal validity or scope of those patents that are brought to its attention. Copyright 2005 IEEE. All rights reserved.iii Introduction This recommende
6、d practice, under the jurisdiction of the Petroleum and Chemical Industry Committee of the IEEE Industry Applications Society, presents the minimum requirements for the construction, manufacturing, purchasing, and application of electric submersible pump cable. The configuration of the cable is eith
7、er round or flat, with ethylene-propylene rubber insulation, with a nitrile jacket, EPDM jacket, or lead sheath and armor. Anyone desiring to use this recommended practice may do so. It is presented as minimum criteria for construction of this class of submersible cable. It is not intended to restri
8、ct innovation or to limit development of improvements in cable design. Every effort has been made to assure the accuracy and reliability of the data contained herein; however, the committee makes no representation, warranty, or guarantee in connection with the publication of this specification and h
9、ereby expressly disclaims any liability or responsibility for loss or damage resulting from its use; for any violation of any federal, state, or municipal regulation with which it may conflict; or for the infringement of any patent resulting from the use of this document. Notice to users Errata Erra
10、ta, if any, for this and all other standards can be accessed at the following URL: http:/ standards.ieee.org/reading/ieee/updates/errata/index.html. Users are encouraged to check this URL for errata periodically. Interpretations Current interpretations can be accessed at the following URL: http:/sta
11、ndards.ieee.org/reading/ieee/interp/ index.html. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken with respect to the existence or validity of any pate
12、nt rights in connection therewith. The IEEE shall not be responsible for identifying patents or patent applications for which a license may be required to implement an IEEE standard or for conducting inquiries into the legal validity or scope of those patents that are brought to its attention. This
13、introduction is not part of IEEE Std 1018-2004, IEEE Recommended Practice for Specifying Electric Submers- ible Pump CableEthylene-Propylene Rubber Insulation. ivCopyright 2005 IEEE. All rights reserved. Participants The following is a list of participants in the Downhole Working Group of the Petrol
14、eum and Chemical Industry Committee. Marcus O. Durham, Chair Thomson H. Wallace, Secretary The following members of the individual balloting committee voted on this recommended practice. Balloters may have voted for approval, disapproval, or abstention. When the IEEE-SA Standards Board approved this
15、 recommended practice on 23 September 2004, it had the following membership: Don Wright, Chair Steve M. Mills, Vice Chair Judith Gorman, Secretary *Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board liaisons: Satish K. Aggarwal, NRC Representative Richard DeBlasio, DOE
16、 Representative Alan Cookson, NIST Representative Michael D. Fisher IEEE Standards Project Editor David Anderson Gordon Baker Lester Gagan Robert Lannom Howard Oswald John Patterson Rodney Story Russell E. Adams J. K. Armintor S. P. Axe David C. Azbill Iraj Boroumand R. Bried D. G. Broussard M. M. C
17、ameron W. F. Casper James M. Daly Stephen M. Dillard Gary Donner Richard Doughty Joseph S. Dudor Marcus O. Durham J. B. Dwyer H. B. Dygert C. J. Erickson E. J. Fagan R. W. Gallant S. W. Hagemoen J. D. Hill F. P. Hogan Richard H. Hulett John Hus Robert M. Jackson Ben Johnson M. Johnson John H. Kasseb
18、aum P. M. Kinney J. C. Lacour W. H. Levers Clark R. Lockerd B. W. McCarty Bob McDaniel Paul W. Myers R. L. Nailen R. A. Neil J. P. Nelson J. B. Overmeyer T. P. Pearson B. M. Polkinghorn J. P. Propst Milton H. Ramsey Quentin Reynolds S. W. Shannon P. J. Skobel A. W. Smith T. B. Smith H. R. Stewart E.
19、 B. Turner Don Vardeman Albert E. Whiteside Barrt Wusenab J. R. Zahn Peter Zoto Chuck Adams Stephen Berger Mark D. Bowman Joseph A. Bruder Bob Davis Roberto de Marca Boisson Julian Forster* Arnold M. Greenspan Mark S. Halpin Raymond Hapeman Richard J. Holleman Richard H. Hulett Lowell G. Johnson Jos
20、eph L. Koepfinger* Hermann Koch Thomas J. McGean Daleep C. Mohla Paul Nikolich T. W. Olsen Ronald C. Petersen Gary S. Robinson Frank Stone Malcolm V. Thaden Doug Topping Joe D. Watson -,-,- Copyright 2005 IEEE. All rights reserved.v Contents 1.Scope 1 2.Normative references. 2 3.Conductors. 2 3.1 Ma
21、terial 2 3.2 Construction. 3 3.3 Conductivity. 3 4.Insulation . 3 4.1 Material 3 4.2 Gas blockage 4 4.3 Construction. 5 5.Barrier (optional) . 5 5.1 Material 5 5.2 Flat cable with lead sheath. 5 6.Assembly and jacket 5 6.1 Material 5 6.2 Construction. 5 7.Armor. 7 7.1 Material 7 7.2 Construction. 8
22、8.Manufacturers electrical test requirements. 8 8.1 Conductor testing. 8 8.2 Electrical testing 8 9.Cable ampacity 12 9.1 Ampacity 12 9.2 Temperature. 12 9.3 Safety factor. 12 9.4 Conductor size . 12 9.5 Economics 13 10.Tutorial information. 13 10.1 Special terms 13 10.2 Application considerations 1
23、6 Annex A (informative) Cable designs and components 18 Annex B (informative) Figures 21 Copyright 2005 IEEE. All rights reserved.1 IEEE Recommended Practice for Specifying Electric Submersible Pump CableEthylene-Propylene Rubber Insulation 1. Scope This recommended practice establishes requirements
24、 for three-conductor new round-and-flat-type oil-well cables used in supplying three-phase ac electric power to submersible pump motors. The three major cables by components are (1) cables with copper conductors, ethylene-propylene diene monomer (EPDM) insulation, nitrile jacket, and galvanized armo
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- IEEE 1018 2004
链接地址:https://www.31doc.com/p-3770684.html