IEEE-C37.09-1999-R2007.pdf
《IEEE-C37.09-1999-R2007.pdf》由会员分享,可在线阅读,更多相关《IEEE-C37.09-1999-R2007.pdf(80页珍藏版)》请在三一文库上搜索。
1、The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2000 by the Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 28 March 2000. Printed in the United States of America. Print: ISBN 0-7381-1783-8 SH947
2、75 PDF: ISBN 0-7381-1784-6 SS94775 No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. IEEE Std C37.09-1999 (R2007) (Revision of IEEE Std C37.09-1979) IEEE Standard Test Procedure for AC Hig
3、h-Voltage Circuit Breakers Rated on a Symmetrical Current Basis Sponsor Switchgear Committee of the IEEE Power Engineering Society Reaffirmed 26 September 2007 Approved 26 June 1999 IEEE-SA Standards Board Abstract: The testing procedures for all high-voltage circuit breakers that include all voltag
4、e ratings above 1000 V ac and comprise both indoor and outdoor types having the prefered ratings as listed in ANSI C37.06-1997 are covered. Typical circuit breakers covered by these standards have max- imum voltage ratings from 4.76 kV through 800 kV, and continuous current ratings of 600 A, 1200 A,
5、 2000 A, and 3000 A associated with the various maximum voltage ratings. The test procedures verify all assigned ratings, including continuous current, dielectric withstand voltages, short-circuit current, transient recovery voltage, and capacitor switching, plus associated capabilities such as mech
6、anical endurance, load current, and out-of-phase switching. Production test procedures are also included. This standard does not cover generator circuit breakers as these are covered in IEEE Std C37.013-1993. Keywords: fast transient recovery voltage, indoor, initial, mechanical endurance, operating
7、 duty, outdoor, power frequency, short-circuit current, short-line fault, single-phase testing, test data re- porting, three-phase testing, unit test, voltage distribution synthetic test. Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELic
8、ensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 02:49:26 MDTNo reproduction or networking permitted without license from IHS -,-,- IEEE Standards documents are developed within the IEEE Societies and the Standards Coordinating Com- mittees of the IEEE Standards Association
9、 (IEEE-SA) Standards Board. Members of the committees serve voluntarily and without compensation. They are not necessarily members of the Institute. The standards developed within IEEE represent a consensus of the broad expertise on the subject within the Institute as well as those activities outsid
10、e of IEEE that have expressed an interest in participating in the development of the standard. Use of an IEEE Standard is wholly voluntary. The existence of an IEEE Standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services r
11、elated to the scope of the IEEE Standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. Every IEEE Standard is subjected to review at
12、 least every fi ve years for revision or reaffi rmation. When a document is more than fi ve years old and has not been reaffi rmed, it is rea- sonable to conclude that its contents, although still of some value, do not wholly refl ect the present state of the art. Users are cautioned to check to det
13、ermine that they have the latest edition of any IEEE Standard. Comments for revision of IEEE Standards are welcome from any interested party, regardless of membership affi liation with IEEE. Suggestions for changes in documents should be in the form of a proposed change of text, together with approp
14、riate supporting comments. Interpretations: Occasionally questions may arise regarding the meaning of portions of standards as they relate to specifi c applications. When the need for interpretations is brought to the attention of IEEE, the Institute will initiate action to prepare appropriate respo
15、nses. Since IEEE Standards represent a consensus of all concerned interests, it is important to ensure that any interpretation has also received the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to pro
16、vide an instant response to interpretation requests except in those cases where the matter has previously received formal consideration. Comments on standards and requests for interpretations should be addressed to: Secretary, IEEE-SA Standards Board 445 Hoes Lane P.O. Box 1331 Piscataway, NJ 08855-
17、1331 USA Authorization to photocopy portions of any individual standard for internal or personal use is granted by the Institute of Electrical and Electronics Engineers, Inc., provided that the appropriate fee is paid to Copyright Clearance Center. To arrange for payment of licensing fee, please con
18、tact Copyright Clearance Center, Cus- tomer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; (978) 750-8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copy- right Clearance Center. Note: Attention is called to the po
19、ssibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken with respect to the existence or validity of any patent rights in connection therewith. The IEEE shall not be responsible for identifying p
20、atents for which a license may be required by an IEEE standard or for conducting inquiries into the legal validity or scope of those patents that are brought to its attention. Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Em
21、ployees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 02:49:26 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright 2000 IEEE. All rights reserved. iii Introduction (This introduction is not part of IEEE Std C37.09-1999, IEEE Standard Test Procedure for AC Hig
22、h-Voltage Circuit Breakers Rated on a Symmetrical Current Basis.) This standard is a major revision of ANSI/IEEE Std C37.09-1979 (R1996). This revision contains major substantive changes. Some editorial changes also have been included, and they are intended to eliminate duplication of words from IEE
23、E Std C37.04-1999 and to reduce the word usage in general. Listed here, for information and guidance, are the substantive changes. This revision refl ects the changes made in ANSI C37.06-1997 where the K factor has effectively been eliminated for all indoor circuit breakers by assigning to it a nume
24、rical value of K = 1. This has been done to take advantage of the newer interrupting technologies. Additionally, the traditional use of 1.6 as the multiplying factor for the asymmetrical root-mean-square (rms) current and 2.7 for the peak current has been revised to refl ect the time constant of 45
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- IEEE C37 09 1999 R2007
链接地址:https://www.31doc.com/p-3771059.html