IEEE-1310-1996-R2004.pdf
《IEEE-1310-1996-R2004.pdf》由会员分享,可在线阅读,更多相关《IEEE-1310-1996-R2004.pdf(23页珍藏版)》请在三一文库上搜索。
1、IEEE Std 1310-1996(R2004) IEEE Trial Use Recommended Practice for Thermal Cycle Testing of Form- Wound Stator Bars and Coils for Large Generators Sponsor Electric Machinery Committee of the IEEE Power Engineering Society Reaffirmed 23 September 2004 Approved 3 July 1996 IEEE Standards Board Abstract
2、: A test method to determine the relative ablility of high-voltage, form-wound stator bars and coils of large rotating machines to resist deterioration due to rapid heating and cooling resulting from machine load cycling is described. Keywords: delamination, form-wound stator bars and coils, similar
3、 design bar/coil, slot section, virgin bar/ coil, thermal cycle testing The Institute of Electrical and Electronics Engineers, Inc. 345 East 47th Street, New York, NY 10017-2394, USA Copyright 1996 by the Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 1996. Pr
4、inted in the United States of America. ISBN 1-55937-759-3 No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. IEEE Standards documents are developed within the IEEE Societies and the Standar
5、ds Coordi- nating Committees of the IEEE Standards Board. Members of the committees serve voluntarily and without compensation. They are not necessarily members of the Institute. The standards developed within IEEE represent a consensus of the broad expertise on the subject within the Institute as w
6、ell as those activities outside of IEEE that have expressed an interest in participating in the develop- ment of the standard. Use of an IEEE Standard is wholly voluntary. The existence of an IEEE Standard does not imply that there are no other ways to produce, test, measure, purchase, market, or pr
7、ovide other goods and services related to the scope of the IEEE Standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. Every IEEE St
8、andard is sub- jected to review at least every five years for revision or reaffirmation. When a document is more than five years old and has not been reaffirmed, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users ar
9、e cautioned to check to determine that they have the latest edition of any IEEE Standard. Comments for revision of IEEE Standards are welcome from any interested party, regardless of membership affiliation with IEEE. Suggestions for changes in documents should be in the form of a proposed change of
10、text, together with appropriate supporting comments. Interpretations: Occasionally questions may arise regarding the meaning of portions of standards as they relate to specific applications. When the need for interpretations is brought to the attention of IEEE, the Institute will initiate action to
11、prepare appropriate responses. Since IEEE Standards rep- resent a consensus of all concerned interests, it is important to ensure that any interpretation has also received the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Com
12、mittees are not able to provide an instant response to interpretation requests except in those cases where the matter has previously received formal consideration. Comments on standards and requests for interpretations should be addressed to: Secretary, IEEE Standards Board 445 Hoes Lane P.O. Box 13
13、31 Piscataway, NJ 08855-1331 USA Authorization to photocopy portions of any individual standard for internal or personal use is granted by the Institute of Electrical and Electronics Engineers, Inc., provided that the appropriate fee is paid to Copyright Clearance Center. To arrange for payment of l
14、icensing fee, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; (508) 750-8400. Permission to photocopy portions of any individual standard for educational class- room use can also be obtained through the Copyright Clearance Center. Note: Attenti
15、on is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken with respect to the existence or validity of any patent rights in connection therewith. The IEEE shall not be respons
16、ible for identifying all patents for which a license may be required by an IEEE standard or for conducting inquiries into the legal validity or scope of those patents that are brought to its attention. iii Introduction (This introduction is not part of IEEE Std 1310-1996, IEEE Recommended Practice f
17、or Thermal Cycle Testing of Form- Wound Stator Bars and Coils for Large Generators.) Peaking duty and pump storage hydrogenerators, synchronous condensers, and gas turbine generators are generally subject to load cycling. This load cycling creates shear stress between copper and the groundwall insul
18、ation of the stator winding that can result in the delamination of the groundwall, and under certain circumstances, into the puncture of the insulation. This standard provides a test procedure that can be performed within a reasonable amount of time for accelerated thermal aging of production, proto
19、type, or similar design bars/coils under laboratory conditions. The effects of this accelerated thermal aging on the bars/coils would provide some indication of the thermal aging of the stator winding of generators subject to cyclic duty. Participants in the Working Group that prepared IEEE Std 1310
20、-1996 are as follows: Chaman L. Kaul, Chair The following persons were on the balloting committee: Edward A. Boulter S. E. Cherukupalli Robert E. Draper Franklin T. Emery Gary C. Griffith Alan M. Iverson J. Langer James F. Lau Steven Lindholm Hartmut Meyer William M. McDermid John B. McMillan G. Har
21、old Miller Charles Millet Beant Nindra M. S. Rana R. H. Reder Howard Sedding Greg Stone John D. Taylor James E. Timperly David Train Richard F. Weddleton Daniel I. Young, Jr. Edward J. Adophson Dana K. Arndt Roy L. Balke E. A. Boulter Robert E. Draper Franklin T. Emery Brian E. B. Gott James J. Gran
22、t Bal K. Gupta Lyle Klataske Terrence J. Lorenz William M. McDermid G. Harold Miller Osman M. Nassar Beant S. Nindra William B. Penn Charles M. Rowe Greg C. Stone James E. Timperly Richard F. Weddleton Daniel I. Young, Jr. iv When the IEEE Standards Board approved this standard on 3 July 1996, it ha
23、d the following membership: Donald C. Loughry, ChairRichard J. Holleman, Vice Chair Andrew G. Salem, Secretary *Member Emeritus Also included are the following nonvoting IEEE Standards Board liaisons: Satish K. Aggarwal Alan H. Cookson Chester C. Taylor Lisa S. Young IEEE Standards Project Editor Gi
24、lles A. Baril Clyde R. Camp Joseph A. Cannatelli Stephen L. Diamond Harold E. Epstein Donald C. Fleckenstein Jay Forster* Donald N. Heirman Ben C. Johnson E. G. “Al” Kiener Joseph L. Koepfinger* Lawrence V. McCall L. Bruce McClung Marco W. Migliaro Mary Lou Padgett John W. Pope Jose R. Ramos Arthur
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- IEEE 1310 1996 R2004
链接地址:https://www.31doc.com/p-3771761.html