《BS-5931-1980.pdf》由会员分享,可在线阅读,更多相关《BS-5931-1980.pdf(16页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS 5931:1980 Code of practice for Machine laid in situ edge details for paved areas UDC 625.888 Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:31:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5931:1980 This British Standard, having been prepared under the direction of
2、the Road Engineering Standards Committee, was published under the authority of the Executive Board and comes into effect on 30 April 1980 BSI 04-1999 The following BSI references relate to the work on this standard: Committee reference RDB/31 Draft for comment 77/14456 DC ISBN 0 580 11367 1 Cooperat
3、ing organizations The Road Engineering Standards Committee, under whose direction this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations: Aluminium FederationFederation of Manufacturers of Asphalt and Coat
4、ed Macadam Association*Construction Equipment and Cranes Association of Consulting EngineersGreater London Council British Quarrying and Slag Federation*Institute of Petroleum British Tar Industry AssociationInstitute of Quarrying Cement and Concrete Association*Institution of Civil Engineers* Concr
5、ete Society Limited*Institution of Highway Engineers* Contractors Plant AssociationInstitution of Municipal Engineers* Convention of Scottish Local AuthoritiesInstitution of Structural Engineers County Surveyors Society*Lighting Industry Federation Limited Department of the Environment (Property Min
6、istry of Defence Services Agency)Refined Bitumen Association Limited Department of the Environment (Transport Road Emulsion Association Limited and Road Research Laboratory)Road Surface Dressing Association Department of Transport*Sand and Gravel Association Federation of Civil Engineering Society o
7、f Chemical Industry Contractors*Trades Union Congress The organizations marked with an asterisk in the above list, together with the following, were directly represented on the committee entrusted with the preparation of this British Standard: Cement Admixtures AssociationNational Paving and Kerb As
8、sociation Cement Makers FederationIndividual expert Institute of Geological Sciences Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:31:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5931:1980 BSI 03-1999i Contents Page Co
9、operating organizations Inside front cover Foreword ii 0 Introduction 1 1 Scope 1 2 References 1 3 General considerations 1 4 Machines for forming in situ edge details 1 5 Section size and tolerances 2 6 Trial lengths 2 7 Asphalt sections 2 8 Concrete sections 4 Appendix A Characteristics of machine
10、s for forming in situ edge details 7 Figure 1 Typical cross sections of asphalt kerbs 8 Figure 2 Typical cross sections of concrete kerbs 9 Table 1 Classification of auger powered kerb extruder machines 7 Publications referred toInside back cover Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 0
11、4 16:31:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5931:1980 ii BSI 03-1999 Foreword Extruded asphalt kerbing was introduced into the United Kingdom from the USA in 1961 and concrete some years later, since which time a substantial amount of experience has been obtained with their use. Some ke
12、rbs of this type have now been in service for over 15 years with satisfactory performance. These recommendations set out to give general information on such kerbs based on this experience. This code recommends good practice for the production of both asphalt and concrete edge details. Specific refer
13、ence to either material is made only where their individual characteristics warrant such reference. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard
14、does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 10, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated
15、. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:31:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5931:1980 BSI 03-19991 0 Introduction 0.1 Uses. Most forms of road-edge detail may be successfully extruded or, for
16、 concrete alone, slip formed. Raised kerbs may be formed on both rigid and flexible pavements during new construction projects. The principle use of machine laid in situ sections in the United Kingdom has been at the back of hardshoulders on motorways as a drainage detail. However there are now many
17、 cases where these sections have been successfully adopted immediately adjoining carriageways on all-purpose roads and on housing estates. Other situations where this type of section may be used include surrounds to vehicle parking areas, as a means of channelling traffic (e.g. at toll booths) and f
18、or the delineation of individual parking bays. Sections may be formed on existing pavements for surface water control, to facilitate provision of footways with minimum cost or for traffic management purposes. Where an edge beam is specified as a buttress or datum for pavement construction, a machine
19、 laid in situ concrete section may be the preferred form of construction and this may include a raised kerb where required. 0.2 Advantages. Machine laid in situ sections can be laid at up to ten times the rate of laying for conventional forms of kerbs. The in situ type of kerb may be superimposed on
20、 existing kerbs thus avoiding taking up and relaying to new levels. It is particularly suitable where a simple addition to an existing pavement is required for surface water control or traffic segregation. Even if the length to be constructed is small but speed is essential, machine laid in situ ker
21、bs, channels or other features may be considered advantageous in spite of any possible additional cost. 0.3 Disadvantages. Line-guided machines are susceptible to inaccuracies or disturbances of line setting possibly leading to expensive remedial works on long lengths of in situ section. Conventiona
22、l pre-cast kerbs are fairly easily adjusted for line and level, and conventional formwork can be checked before concrete is placed. Apart from the question of cross-sectional area, the main limitation on the use of an extrusion machine is the presence of obstacles adjacent to the line of the section
23、. For example, the machines cannot normally be operated immediately against bridge parapets, walls, etc. although, to overcome this problem, hand placing of pre-extruded section may be practicable. Machine laid in situ concrete is not readily adapted to allow for settlement or alteration to provide
24、for accesses. Extruded asphalt is more readily adapted than concrete to provide entrances and replacement of damaged sections. Aesthetically, asphalt sections are vulnerable to damage from heavy traffic particularly in the first few weeks of life and they may soften in extremely hot weather. 1 Scope
25、 This code gives information and recommendations about the use of extruded-asphalt or extruded-concrete, and slip-formed concrete road-edge features such as kerbs or channels. Details of asphalt and concrete mixes that are suitable for the processes are given together with construction details. This
26、 code does not provide recommendations for the forming of such edge features monolithically with paved areas nor on the forming of safety barriers. 2 References The titles of the publications referred to in this code are listed on the inside back cover. 3 General considerations In general, the case
27、for or against the adoption of a machine laid in situ section is one of economics. Where a kerb is to be formed on the surface of a new pavement the cost of that portion of the pavement should be added to that of the kerb. Because the mechanized construction of in situ edge details is a specialized
28、process, it is recommended that experienced machine operators be employed. Continuity of experience is also desirable. Construction should be a continuous process and it is recommended that the supply of materials should be co-ordinated with the output of the particular machine. Where line-guided ma
29、chines are used, care should be taken to ensure that the line is not displaced. 4 Machines for forming in situ edge details 4.1 General considerations. There are two basic types of machine commonly referred to as: a) extrusion machines; b) slip-form machines. Further details of the characteristics o
30、f both types are given in Appendix A. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:31:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5931:1980 2 BSI 03-1999 The selection of a machine for a particular project should take account of: a) the material to be laid; b) the section dimension
31、s; c) in the case of concrete, whether dowels or reinforcement are to be included. Asphalt may be laid by only certain of the extrusion machines. Plain concrete may be laid by either extrusion or slip forming machines. Reinforced concrete or that containing vertical dowels, may be laid by most slip
32、forming machines but not by extrusion machines. 4.2 Auger powered extrusion machines. To achieve the correct density there is a critical relationship between machine mass, auger size and number of augers to the cross-sectional area of the mould. The density of the extruded section is a direct result
33、 of the resistance of the machine to forward movement. Hence a machine of a mass appropriate to the section dimensions should be selected (see Appendix A). 5 Section size and tolerances 5.1 General. A wide variety of kerb, kerb and gulley, channel, edge beams and ditch liners can be achieved. There
34、are some physical limitations, however, that affect the choice of machine as indicated in 4.1 and Appendix A. Most slip-form machines will accept moulds for almost any section from 120 mm 120 mm chamfered kerb upwards. Many can place structures, such as kerb and footpath combined, up to 1.5 m to 2 m
35、 wide and a few will accept moulds up to 3 m wide. The auger powered extruding machines are more limited. Whilst machine laid kerbs are preferably laid to straight line or gentle curves, it is possible for them to be satisfactorily laid to radii as sharp as 5 m. Abrupt changes in kerb-line and level
36、, e.g. at gulley outlets or at dropped kerbs, should receive special attention as indicated in 7.3.6 and 8.5.6. 5.2 Dimensional tolerances on cross section of moulds. The tolerance on the cross section of the mould should be 3 mm. 5.3 Finished tolerances on alignment. Except in the case of line-guid
37、ed machines the regularity of asphalt kerbs with respect to level depends on the accuracy of finish of the surface on which it is laid. In the case of line-guided machines the surface regularity of the top of the kerb should be within 3 mm of the theoretical line. The horizontal alignment should not
38、 depart from the intended line by more than 13 mm nor deviate from the straight by more than 3 mm in 3 m. Where false falls have been provided in the pavement surfacing to assist drainage in the channels, except where a line-guided machine is used, special measures are usually necessary to ensure th
39、at the kerb level follows the true road level rather than that of the falls. It may simply require adjustments to be made to the height of the wheels of the extrusion machine or it may be necessary to run the machine on a short length of suitably supported track or board, placed at the required datu
40、m. Alternatively, consideration should be given to the use of pre-extruded kerbs laid on an in situ bed such as would normally be laid for conventional kerbs. 6 Trial lengths Before commencing any contract it is recommended that the contractor, having selected a mix, should demonstrate, by laying a
41、trial length, that this mix, the plant, equipment and method of construction will produce an acceptable end product. Such trial lengths should be assessed for the required degree of compaction, a uniform surface finish free from blemishes, accurate cross-sectional dimensions and longitudinal alignme
42、nt. The capability of the machine to do the curve and gradient work required in the contract should be checked during the trial. Consideration should be given to the siting of the trial length so that, if successful, it can form part of the main work. Once the mix details, plant and method of constr
43、uction have been chosen, these should not be varied without the prior approval of the engineer. 7 Asphalt sections 7.1 General. Experience in the United Kingdom has shown that rolled asphalt mixes of the type described in BS 594 are most suitable for extrusion. Recommended recipe mixes are detailed
44、as follows. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:31:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5931:1980 BSI 03-19993 7.2 Materials. A nominal coarse aggregate content within the range 20 % to 30 % is recommended, although other stone contents have been successfully used.
45、The nominal size of the coarse aggregate should not exceed 20 mm and will normally be 10 mm. The aggregate type and other properties should comply with the requirements of BS 594. The binder content of the asphalt mix should normally lie within the range 6 % to 9 % although some aggregates may requi
46、re 0.5 % to 1 % more binder. It is recommended that the binder be 50, 70 or 100 penetration grade. In general the upper range of binder content and the lower range of penetration will lead to a more durable kerb. In situations where the kerbs will be immediately adjoining a carriageway and where the
47、re is a high risk of mechanical damage from vehicle impact, a harder grade of binder (e.g. 35-pen), coupled with the upper range of coarse aggregate content may be considered more appropriate. The final mix composition will depend on the type of machine, the profile specified and the nature of the c
48、oarse aggregate. The normal tolerances specified in BS 594 with respect to composition of the mixture apply to asphalt mixes to be used for extruded kerbing. 7.3 Construction 7.3.1 Setting out. Asphalt kerb extrusion does not necessarily require the setting of rails or guide wires and it is common p
49、ractice simply to work to a string or chalk guide line on the surface on which the kerbs are to be placed. 7.3.2 Preparation of foundation. Asphalt kerbs may be extruded on to the basecourse or wearing course of a flexible construction or, in the case of a rigid construction, on the finished concrete. The surface on which the kerbs are to be laid should be dry and cleaned of loose or deleterious material. 7.3.3 Bond. Except in the case of freshly laid bituminous pavements, a tackcoat of either bitumen emulsion complying with the requirements of class A1-40 or class
链接地址:https://www.31doc.com/p-3772331.html