GMNA-GM4195M-1997.pdf
《GMNA-GM4195M-1997.pdf》由会员分享,可在线阅读,更多相关《GMNA-GM4195M-1997.pdf(3页珍藏版)》请在三一文库上搜索。
1、I GENERAL MOTORS ENGINEERING STANDARDS I Materials and Processes - Metals 1 Rev B C BEARING AND BUSHING ALLOY GM3874M GM3889M GM431M GM4111M GM4167M GM4168M GM4195M Date Description 4/89 Editorial 11/97 Editorial: akas added GM6158M GM Spedfi- cation Numbers 3874M 4167M 4168M 4195M 1 SCOPE. niis sta
2、ndard covers lead, tin and aluminum alloys used primarily as overlays and overplates in bearing composites. (Coverage for composites are published elsewhere in the GM Standards.) 1.1 GM3874M, GM4167M, GM4168M, and GM4195M are Lead Base. GM4031M and GM4111M are Tin Base. GM3889M, GM6158M. and GM6159M
3、 are Aluminum Base. 1.2 RESTRICTED AND REPORTABLE CHEMICALS (GMlOOOM). A l i materials supplied to this Specification must comply with the requllements listed in GMlOOOM, Restricted and Reportable CherniealS. 2 REFERENCED STANDARDS. Sim- Pb % SN Cu Sb % As S % Bi% Fe % Ni % A i % Zn % Other Other ii
4、ar % % S S SAE Each Total 5460 % 19 Balance 8.0- 1.25 - - - - 0.10 - 0.005 0.005 0.05 0.50 12.0 - 3 .OO 16 Balance 4.20 0.02 3.25 - 0.05 0.0015 0.10 0.10 0.01 0.005 0.005 0.03 0.20 - - 3.75 - 0.005 0.03 4.70 0.05 3.0 - 3.5 0.10 4.0 4.70 7.0 11.0 11.0 16.0 - 0.6 0.005 - 13 Balance 5.0 - 0.70 9.0- 0.1
5、0 0.005 0.10 0.01 0.01 0.005 0.005 0.30 0.50 14 Balance 9.0 - 0.50 14.0- 0.30 0.0015- 0.10 0.01 0.01 0.005 0.005 0.03 0.20 GMlOOOM 3 CHEMICAL AND PHYSICAL PROPERTIES. Materials shall conform to the limits shown in Tables 1 through 3 for the applicable GM numbers. 3.1 Bearing materials shall be free
6、of aii defects detrimental to the performance of the materiai in processing or service. 4 INITIAL SOURCE APPROVAL. No shipment shall be made by any supplier until representative initial production samples have been approved by engineering as meeting the requirements of this specification. 4.1 Comple
7、ted copies of the Material Safety Data Sheet meeting GM information requirements must be submitted with GM6159M any new submissions or whenever a composition change has occurred 5 INSPECTION AND REJECTION. All shipments of material or parts under contract or purchase order manufac- aired to this spe
8、cification shali be equivalent in every respect to the i n i t i a i samples approved by engineering. There shali be no changes in either formuiation or manufacturing processes permitted without prior notification and approval by engineer- ing. Lack of notification by the supplier constitutes ground
9、s for rejection of any shipment. While samples may be taken h m incoming shipments and checked for conformance to this specification, the supplier shall accept the responsibility for incoming shipments meeting this specification without depen- dence upon purchasers inspection. 6 APPROVED SOURCES. En
10、gineering qualification of an approved some is required for this specification. only sources listed in the GM Corporate Materials File under this specification number have been qualified by engineering as meeting the requirements of this specification. Sources are available through the on-line MATSP
11、C System. 7 GENERAL INFORMATION. This standard was issued in July 1934. The latest revisions include: TABLE 1 - LEAD BASE BEARING ALLOYS (NOTE) Q Cq&htDECEMBER 1897 oensral MdasCixpWm All Rights Reswwd DECEMBER 1997 PAGE 1 3874M Copyright General Motors North America Provided by IHS under license wi
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GMNA GM4195M 1997
链接地址:https://www.31doc.com/p-3772937.html