《BS-6906-3-1989.pdf》由会员分享,可在线阅读,更多相关《BS-6906-3-1989.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS 6906-3: 1989 Methods of test for Geotextiles Part 3: Determination of water flow normal to the plane of the geotextile under a constant head UDC 677.01032.2:532.5:620.1 Licensed Copy: sheffieldun sheffieldun, na, Wed Dec 06 12:57:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6
2、906-3:1989 This British Standard, having been prepared under the direction of the Textiles and Clothing Standards Policy Committee, was published under the authority of the Board of BSI and comes into effect on 30 November 1989 BSI 02-1999 The following BSI references relate to the work on this stan
3、dard: Committee reference TCM/35 Draft for comment 87/45227 DC ISBN 0 580 17595 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Textiles and Clothing Standards Policy Committee (TCM/-) to Technical Committee TCM/35, upon which the foll
4、owing bodies were represented: Association of Consulting Engineers British Polyolefin Textiles Association British Railways Board Chemical Industries Association Department of Transport Department of Transport (Transport and Road Research Laboratory) ERA Technology Ltd. Federation of Civil Engineeri
5、ng Contractors Institution of Civil Engineers Man-made Fibres Producers Committee Ministry of Agriculture, Fisheries and Food Ministry of Defence Textile Research Council Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: sheffieldun sheffieldun, na, Wed Dec 06 12:57:27
6、 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6906-3:1989 BSI 02-1999i Contents Page Committees responsibleInside front cover Forewordii 1Scope1 2Principle1 3Apparatus1 4Test specimens1 5Procedure1 6Calculation and expression of results2 7Test report2 Appendix A Accuracy3 Figure 1 Examples of appar
7、atus for determining water flow3 Figure 2 Water viscosity correction factor Rt5 Publications referred toInside back cover Licensed Copy: sheffieldun sheffieldun, na, Wed Dec 06 12:57:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6906-3:1989 ii BSI 02-1999 Foreword This Part of BS 6906 has been pr
8、epared under the direction of the Textiles and Clothing Standards Policy Committee. The water flow through a geotextile is dependent upon its thickness, number and size of pores and the water flow path. The method described in this standard is a procedure for determining water flow normal to the pla
9、ne of the geotextile. Determination of water flow through the plane of the geotextile will be covered in a subsequent Part of BS 6906. The test described in this standard is basically an index test which gives values which are primarily of use when comparing one geotextile with another. Inevitably w
10、here a geotextile is to be used in structures where the system permeability is of importance then some derivation of effective hydraulic conductivity will be made from the flow rate through the geotextile. It is of paramount importance that designers are aware that the flow rate quoted is likely to
11、be significantly greater than the system permeability incorporating the geotextile, for which reasons factor of safety of the order of 10 have been suggested when interpreting flow rates/permeability of geotextiles. It is further evident that the hydraulic conditions in which a geotextile is placed
12、have a profound effect upon the permeability of that material. The necessary ideal laboratory test conditions are unlikely to be repeated in the field. Care should therefore be taken when attempting to apply the results of this test to the field performance of a geotextile, particularly as the test
13、is performed on geotextiles in isolation. Some geotextiles wet up readily when exposed to water whereas others wet up only slowly and can support an appreciable head of water before “breakthrough” occurs. The procedure described in this method has been written with these characteristics in mind. Oth
14、er Parts of BS 6906 are as follows. Part 1: Determination of the tensile properties using a wide width strip; Part 2: Determination of the apparent pore size distribution by dry sieving; Part 4: Determination of puncture resistance (CBR puncture test). At the time of publication of this Part of BS 6
15、906 no corresponding international standards exist. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal ob
16、ligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table o
17、n the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Wed Dec 06 12:57:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6906-3:1989 BSI 02-19991 1 Scope This Part of BS 6906 describes a procedure for determining water flow through geotextiles under conditions of a constant head with
18、uni-directional flow with the geotextile uncompressed and isolated. The test is applicable to all types of geotextile with an anticipated water flow of less than 300 L s1 m2 at a head of 100 mm. NOTE 1Information on the accuracy of the test is given in Appendix A. NOTE 2The titles of the publication
19、s referred to in this standard are listed on the inside back cover. 2 Principle The flow of water through a single layer of geotextile normal to the plane of the geotextile is measured under specified conditions. 3 Apparatus 3.1 Water permeability apparatus, complying with the following. a) It shall
20、 be capable of applying various heads in the range 50 mm to 300 mm across the specimen and maintaining a constant head for the duration of one test with water on both sides of the specimen. b) The specimen area exposed to testing shall be circular with a minimum diameter of 40 mm. The diameter shall
21、 be measured to the nearest millimetre. c) The apparatus shall allow at least 1 L of water to be collected in a collection time of 10 s. d) There is no head when the test is performed with no test specimen. NOTEExamples of apparatus for determining water flow are shown in Figure 1. 3.2 Water, at a t
22、emperature of between 10 C and 25 C. NOTEDue to problems caused by the release of air bubbles, the water should not be fed into the apparatus direct from a mains supply. The water should be de-aired or fed from a still tank but should not be recycled. The water should be filtered if suspended solids
23、 are visible to the naked eye or if solids accumulate on or in the specimen thus invalidating the test. 3.3 Stopwatch, having an accuracy of 0.1 s. 3.4 Thermometer, having an accuracy of 0.1 C. 3.5 Measuring vessel, for determining volume to an accuracy of 10 mL. 3.6 Balance, capable of determining
24、mass to an accuracy of 1 mg. 3.7 Means of measuring dimensions of test specimens, to an accuracy of at least 1 mm. 4 Test specimens 4.1 Selection Take specimens at random from the sample. Unless otherwise agreed between the interested parties, do not take specimens from within 100 mm of the selvedge
25、 of the geotextile. 4.2 Number and dimensions Unless otherwise agreed between interested parties, cut five test specimens from the sample, each of suitable dimensions for the water permeability apparatus to be used (3.1). Where it is necessary to determine the results to within a given confidence in
26、terval of the mean, determine the number of test specimens in accordance with BS 2846-2. 4.3 Specimen condition The specimens shall be clean and dry. 4.4 Mass per unit area Determine the dimensions (3.7) and mass (3.6) of the test specimens, and calculate the mass per unit area. 5 Procedure 5.1 Asse
27、mble the water permeability apparatus (3.1) with the test specimen (clause 4) in place. Ensure that all joints are watertight. 5.2 Introduce an increasing head of water (3.2) on one side of the test specimen while the other side remains exposed to air i.e. the head of water is above the specimen in
28、the apparatus shown in Figure 1(a) and below the specimen in the apparatus shown in Figure 1(b). Record the head of water achieved before flow is initiated as the breakthrough head. 5.3 Continue increasing the head to 150 mm to wet out the specimen. 5.4 Fill the apparatus with water i.e. from the bo
29、ttom upwards when using the apparatus in Figure 1(a) through the specimen until there is a minimum 50 mm depth of water above the specimen with zero head (i.e. no flow through the specimen). NOTEThis stage may not be necessary if the apparatus fills during the procedure described in 5.3. 5.5 The wat
30、er level should equalize very quickly. If it does not equalize within 5 min remove any trapped air from under the specimen by suction and reapply a 150 mm head. 5.6 Commence flow, adjusting the inlet to give a constant head of 100 2 mm. Licensed Copy: sheffieldun sheffieldun, na, Wed Dec 06 12:57:27
31、 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6906-3:1989 2 BSI 02-1999 5.7 When the head has been steady for a minimum of 30 s collect the water passing through the system in a measuring vessel (3.5) over a fixed period of time. 5.8 Record the volume collected to the nearest 10 mL, the time to the
32、 nearest 0.1 s (3.3) and the water temperature to the nearest 0.1 C (3.4). NOTEThe volume collected should be a minimum of 1 L; the collection time should be a minimum of 10 s. 5.9 Readjust if necessary to give a 100 2 mm head and repeat the procedure detailed in 5.6 to 5.8 two more times. 5.10 If a
33、greed between the interested parties, repeat the procedures detailed in 5.6 to 5.8 but with a head of 50 2 mm. 5.11 If agreed between the interested parties, repeat the procedures detailed in 5.6 to 5.8 but with a head of 150 2 mm. 5.12 Repeat the whole procedure with each of the four remaining spec
34、imens. 6 Calculation and expression of results Calculate the flow rate (F) in L s1 m2 and correct to 20 C using the following equation: where Calculate the mean flow rate (in L s1 m2) for each specimen and the coefficient of variation between the means at 100 mm head (and, if agreed between the inte
35、rested parties, at 50 mm and 150 mm heads). 7 Test report The test report shall include the following information: a) the number and date of this British Standard, i.e. BS 6906-3:1989; b) a description of the geotextile tested; c) the area of specimen tested (in mm2); d) the mass per unit area (in g
36、/m2) of the specimens (see 4.4); e) the breakthrough head (in mm); f) details of apparatus used including specimen area exposed; g) temperature of the water used (in C); h) the results obtained, expressed as in clause 6, for 100 mm head; i) if agreed between the interested parties, the results obtai
37、ned, expressed as in clause 6, for 50 mm and 150 mm heads. Qis the recorded flow volume (in L); A is the tested area (in m2); tis the recorded time of test (in s); Rtis the temperature correction factor from Figure 2. F QRt At - -= Licensed Copy: sheffieldun sheffieldun, na, Wed Dec 06 12:57:27 GMT+
38、00:00 2006, Uncontrolled Copy, (c) BSI BS 6906-3:1989 BSI 02-19993 Appendix A Accuracy Based on the results of interlaboratory trials the coefficient of variation of repeat tests on the same specimen is less than 5 %. The coefficient of variation of measurements from different specimens depends on t
39、he intrinsic variability of the geotextile. Typical geotextiles give coefficients of variation of up to 20 %. Figure 1 Examples of apparatus for determining water flow Licensed Copy: sheffieldun sheffieldun, na, Wed Dec 06 12:57:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6906-3:1989 4 BSI 02-1
40、999 Figure 1 Examples of apparatus for determining water flow (concluded) Licensed Copy: sheffieldun sheffieldun, na, Wed Dec 06 12:57:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6906-3:1989 BSI 02-19995 Figure 2 Water viscosity correction factor Rt Licensed Copy: sheffieldun sheffieldun, na, W
41、ed Dec 06 12:57:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 6 blank Licensed Copy: sheffieldun sheffieldun, na, Wed Dec 06 12:57:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6906-3:1989 BSI 02-1999 Publications referred to BS 2846, Guide to statistical interpretation of data. BS 2846-2, Estima
42、tion of the mean: confidence interval. BS 6906, Methods of test for geotextiles. BS 6906-1, Determination of the tensile properties using a wide width strip1). BS 6906-2, Determination of the apparent pore size distribution by dry sieving1). BS 6906-4, Determination of puncture resistance (CBR punct
43、ure test)1). 1) Referred to in the foreword only. Licensed Copy: sheffieldun sheffieldun, na, Wed Dec 06 12:57:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
44、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on stand
45、ards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality
46、of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. B
47、SI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax:
48、 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and interna
49、tional standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax:
链接地址:https://www.31doc.com/p-3772996.html