IEC-61499-2-2005.pdf
《IEC-61499-2-2005.pdf》由会员分享,可在线阅读,更多相关《IEC-61499-2-2005.pdf(48页珍藏版)》请在三一文库上搜索。
1、 INTERNATIONAL STANDARD IEC 61499-2 First edition 2005-01 Function blocks Part 2: Software tools requirements Reference number IEC 61499-2:2005(E) Publication numbering As from 1 January 1997 all IEC publications are issued with a designation in the 60000 series. For example, IEC 34-1 is now referre
2、d to as IEC 60034-1. Consolidated editions The IEC is now publishing consolidated versions of its publications. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publication incorporating amendment 1 and the base publication incorporating amendments
3、 1 and 2. Further information on IEC publications The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. Information relating to this publication, including its validity, is available in the IEC Catalogue of pub
4、lications (see below) in addition to new editions, amendments and corrigenda. Information on the subjects under consideration and work in progress undertaken by the technical committee which has prepared this publication, as well as the list of publications issued, is also available from the followi
5、ng: IEC Web Site (www.iec.ch) Catalogue of IEC publications The on-line catalogue on the IEC web site (www.iec.ch/searchpub) enables you to search by a variety of criteria including text searches, technical committees and date of publication. On-line information is also available on recently issued
6、publications, withdrawn and replaced publications, as well as corrigenda. IEC Just Published This summary of recently issued publications (www.iec.ch/online_news/ justpub) is also available by email. Please contact the Customer Service Centre (see below) for further information. Customer Service Cen
7、tre If you have any questions regarding this publication or need further assistance, please contact the Customer Service Centre: Email: custserviec.ch Tel: +41 22 919 02 11 Fax: +41 22 919 03 00 INTERNATIONAL STANDARD IEC 61499-2 First edition 2005-01 Function blocks Part 2: Software tools requireme
8、nts IEC 2005 Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission, 3, rue de V
9、aremb, PO Box 131, CH-1211 Geneva 20, Switzerland Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch X For price, see current catalogue PRICE CODE Commission Electrotechnique Internationale International Electrotechnical Commission 2 61499-2 IEC:2005(E) CONTEN
10、TS FOREWORD.3 1 Scope 6 2 Normative references .6 3 Terms and definitions .6 4 Software tool requirements .7 4.1 Information to be provided by the software tool supplier .7 4.2 Exchange of library elements.7 4.3 Information to be provided by the supplier of library elements.7 4.4 Display of declarat
11、ions.8 4.5 Modification of declarations .8 4.6 Validation of declarations.8 4.7 Implementation of declarations 8 4.8 System operation, testing and maintenance .8 Annex A (normative) Document Type Definitions (DTDs) 9 Annex B (informative) Graphics model25 Annex C (informative) Examples 28 Figure B.1
12、 Graphics model.25 Figure B.2 ECC drawing example.27 Table A.1 Document Type Definition (DTD) elements9 Table A.2 DataType DTD .10 Table A.3 DataType DTD Elements 11 Table A.4 Library Element DTD14 Table A.5 LibraryElement DTD Elements19 -,-,- 61499-2 IEC:2005(E) 3 INTERNATIONAL ELECTROTECHNICAL COM
13、MISSION _ FUNCTION BLOCKS Part 2: Software tool requirements FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co
14、-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred
15、to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in thi
16、s preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an internationa
17、l consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable ef
18、forts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publica
19、tions transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval an
20、d cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts
21、and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publi
22、cation or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publi
23、cation may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61499-2 has been prepared by IEC technical committee 65: Industrial-process measurement and control. This standard cancels and replaces IEC/PAS 6149
24、9-2 published in 2001. This first edition constitutes a technical revision. The following major technical changes have occurred between the PAS edition and this edition: a) Syntax for network segments, links and parameters has been added in Annex A for consistency with IEC 61499-1. b) Syntax for par
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- IEC 61499 2005
链接地址:https://www.31doc.com/p-3773286.html