ISO-10442-2002.pdf
《ISO-10442-2002.pdf》由会员分享,可在线阅读,更多相关《ISO-10442-2002.pdf(78页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 10442:2002(E) ISO 2002 INTERNATIONAL STANDARD ISO 10442 First edition 2002-12-01 Petroleum, chemical and gas service industries Packaged, integrally geared centrifugal air compressors Industries du ptrole, de la chimie et du gaz naturel Compresseurs dair centrifuges assembls mu
2、ltiplicateur intgr Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 21:31:04 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10442:2002(E) PDF
3、disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, part
4、ies accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative
5、to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2002 A
6、ll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country
7、 of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2002 All rights reserved Copyright International Organization for Standardization Provided by IHS under license w
8、ith ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 21:31:04 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10442:2002(E) ISO 2002 All rights reserved iii Contents Foreword iv Introduction. v 1 Scope 1 2 Normative references 1 3 Term
9、s and definitions. 2 4 Basic design 4 4.1 General. 4 4.2 Package 7 4.3 Integrally geared compressor 19 4.4 Driver 33 4.5 Driver-to-compressor coupling and guard. 34 4.6 Intercoolers 35 5 Accessories . 35 5.1 Aftercooler . 35 5.2 Air intake filter-silencer 36 5.3 Discharge blowoff silencer 36 6 Inspe
10、ction, testing and preparation for shipment . 36 6.1 General. 36 6.2 Inspection 37 6.3 Testing 37 6.4 Preparation for shipment 40 7 Vendor data 41 7.1 Proposals. 41 7.2 Contract data . 42 Annex A (informative) Data sheets . 46 Annex B (informative) Material specifications for major component parts 5
11、9 Annex C (informative) Diagrams (see ISO 10439) 62 Annex D (normative) Forces and moments. 66 Bibliography 69 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 21:31:04 MDTN
12、o reproduction or networking permitted without license from IHS -,-,- ISO 10442:2002(E) iv ISO 2002 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International St
13、andards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also
14、 take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committee
15、s is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possib
16、ility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10442 was prepared by Technical Committee ISO/TC 118, Compressors, pneumatic tools and pneumatic machines, in colla
17、boration with Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 6, Processing equipment and systems. Annex D forms a normative part of this International Standard. Annexes A, B and C are for informatio
18、n only. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 21:31:04 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10442:2002(E) ISO 2002 All ri
19、ghts reserved v Introduction This International Standard is based on the American Petroleum Institutes API Std 672, second edition, April 1988. Some of the content of this International Standard is identical or similar to ISO 10439, which covers centrifugal compressors for the petroleum, chemical an
20、d gas service industries. Users of this International Standard should be aware that further or differing requirements may be needed for individual applications. This International Standard is not intended to inhibit a vendor from offering, or the purchaser from accepting, alternative equipment or en
21、gineering solutions for the individual application. This may be particularly applicable where there is innovative or developing technology. Where an alternative is offered, the vendor should identify any variations from this International Standard and provide details. Copyright International Organiz
22、ation for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 21:31:04 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS
23、 under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 21:31:04 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 10442:2002(E) ISO 2002 All rights reserved 1 Petroleum, chemical and gas service indus
24、tries Packaged, integrally geared centrifugal air compressors 1 Scope This International Standard specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of constant-speed, packaged, integrally geared centrifugal air c
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 10442 2002
链接地址:https://www.31doc.com/p-3773788.html