ISO-10472-3-1997.pdf
《ISO-10472-3-1997.pdf》由会员分享,可在线阅读,更多相关《ISO-10472-3-1997.pdf(18页珍藏版)》请在三一文库上搜索。
1、A Reference number ISO 10472-3:1997(E) INTERNATIONAL STANDARD ISO 10472-3 First edition 1997-12-15 Safety requirements for industrial laundry machinery Part 3: Washing tunnel lines including component machines Exigences de scurit pour les machines de blanchisserie industrielle Partie 3: Trains de la
2、vage incluant les machines composantes Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 06:31:13 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1047
3、2-3:1997(E) ISO 1997 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization fo
4、r Standardization Case postale 56 CH-1211 Genve 20 Switzerland Internetcentraliso.ch X.400c=ch; a=400net; p=iso; o=isocs; s=central Printed in Switzerland ii Contents Page 1Scope.1 2Normative references.1 3Definitions.2 4Hazards3 5Safety requirements and/or measures for the hazards identified in cla
5、use 4.5 5.1General 5 5.2Mechanical hazards5 5.2.1Interface between loading system and continuous tunnel washing machine .5 5.2.2Continuous tunnel washing machine.5 5.2.3Conveyors between washing machine and squeeze press or centrifugal extraction machine5 5.2.4Squeeze press.5 5.2.5Centrifugal extrac
6、tion machine.6 5.2.6Transfer conveyor system .6 5.2.7Automatic transfer tumbler dryers .6 5.2.8Interface between tumbler dryers and unloading system7 5.3Electrical hazards7 5.4Thermal hazards.7 5.5Hazards generated by noise 7 5.6Hazards associated with materials and substances7 5.6.1Fire and explosi
7、on7 5.6.2Biological hazards.7 5.7Failure of control systems .8 5.8Hazards associated with complex installations.8 6Verification of safety requirements and/or measures.8 7Information concerning machine use.12 7.1Instruction handbook.12 7.2Warning signs.12 Copyright International Organization for Stan
8、dardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 06:31:13 MDTNo reproduction or networking permitted without license from IHS -,-,- ISOISO 10472-3:1997(E) iii Foreword ISO (the International Organization for Standardization)
9、 is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be repre
10、sented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standar
11、ds adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 10472-3 was prepared by Technical Committee ISO/TC 72, Textile machinery
12、and machinery for dry-cleaning and industrial laundering, Subcommittee SC 5, Industrial laundry and dry-cleaning machinery. ISO 10472 consists of the following parts, under the general title Safety requirements for industrial laundry machinery: Part 1: Common requirements Part 2: Washing machines an
13、d washer-extractors Part 3: Washing tunnel lines including component machines Part 4: Air dryers Part 5: Flatwork ironers, feeders and folders Part 6: Ironing and fusing presses Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical St
14、andards 1/9972545001 Not for Resale, 04/20/2007 06:31:13 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10472-3:1997(E) ISO iv Introduction This part of ISO 10472 is intended to instruct the designer of industrial laundry machinery in a systematic manner, focusing on h
15、is particular type of machine, regarding the relevant essential safety requirements, and to suggest possible state-of-the-art safety solutions. The extent to which hazards are covered is indicated in the scope of this part of ISO 10472. In addition, machinery should comply as appropriate with ISO/TR
16、 12100-1 and ISO/TR 12100-2 for hazards which are not specifically referred to in this part of ISO 10472. All examples given in this part of ISO 10472 represent the state of the art. Equivalent solutions are acceptable, provided they attain at least the same safety level. The designer is presumed to
17、 have taken into account all the provisions of ISO 10472-1 before considering this part of ISO 10472. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 06:31:13 MDTNo reproduction
18、or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISOISO 10472-3:1997(E) 1 Safety requirements for industrial laundry machinery Part 3: Washing tunnel lines including component machines 1Scope This part of ISO 10472 covers, together with ISO 10472-1, most significant haza
19、rds associated with washing tunnel lines including component machines such as: continuous tunnel washing machines; squeeze presses or centrifugal extraction machines; transfer conveyor systems; automatic transfer tumblers; loading or unloading system interfaces; access platform and ladders. This par
20、t of ISO 10472 does not cover particular hazards for continuous stand-alone washing lines for endless towels. This part of ISO 10472 does not cover the hazards caused by processing work which may create an explosive or flammable atmosphere inside the machine. This part of ISO 10472 complements the b
21、asic requirements laid down in ISO/TR 12100-1 and ISO/TR 12100-2. It also gives guidance to the designer on assessing the risks associated with the hazards (see EN 1050) and on selecting measures for attaining the required safety level. This part of ISO 10472 does not apply to ancillary equipment, e
22、. g. chemical store and supply pumps, steam valves and supply pipework, vent systems, work feed systems and discharge systems and ducting to the atmosphere. 2Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of I
23、SO 10472. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreement based on this part of ISO 10472 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC
24、 and ISO maintain registers of currently valid International Standards. ISO 6182-1:1993, Fire protection Automatic sprinkler systems Part 1: Requirements and test methods for sprinklers. ISO 10472-1:1997, Safety requirements for industrial laundry machinery Part 1: Common requirements. ISO/TR 12100-
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 10472 1997
链接地址:https://www.31doc.com/p-3773790.html