ISO-10542-5-2004.pdf
《ISO-10542-5-2004.pdf》由会员分享,可在线阅读,更多相关《ISO-10542-5-2004.pdf(14页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO 10542-5 First edition 2004-04-01 Reference number ISO 10542-5:2004(E) ISO 2004 Technical systems and aids for disabled or handicapped persons Wheelchair tiedown and occupant-restraint systems Part 5: Systems for specific wheelchairs Assistances et aides techniques pour les
2、 personnes invalides ou handicapes Systmes dattache du fauteuil roulant et de retenue de loccupant Partie 5: Systmes pour fauteuils roulants particuliers Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not
3、 for Resale, 04/21/2007 11:10:49 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10542-5:2004(E) ii ISO 2004 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed b
4、ut shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this
5、 area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for u
6、se by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, el
7、ectronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightis
8、o.org Web www.iso.org Published in Switzerland Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 11:10:49 MDTNo reproduction or networking permitted without license from IHS -,-,-
9、ISO 10542-5:2004(E) ISO 2004 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. E
10、ach member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internati
11、onal Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standa
12、rds adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject
13、 of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10542-5 was prepared by Technical Committee ISO/TC 173, Technical systems and aids for disabled or handicapped persons, Subcommittee SC 1, Wheelchairs. ISO 10542 consists of the following parts, u
14、nder the general title Technical systems and aids for disabled or handicapped persons Wheelchair tiedown and occupant-restraint systems: Part 1: Requirements and test methods for all systems Part 2: Four-point strap-type tiedown systems Part 3: Docking-type tiedown systems Part 4: Clamping tiedown s
15、ystems Part 5: Systems for specific wheelchairs Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 11:10:49 MDTNo reproduction or networking permitted without license from IHS -,-,-
16、 ISO 10542-5:2004(E) iv ISO 2004 All rights reserved Introduction Providing effective crash protection for wheelchair-seated occupants of motor vehicles generally requires the installation and use of equipment to tie down the wheelchair and restrain the occupant of the wheelchair. ISO 10542-1 establ
17、ishes general requirements and test methods for wheelchair tiedown and occupant restraint systems (WTORS) that are designed for use with a wide range of wheelchairs and adult occupants. This part of ISO 10542 establishes additional or alternative requirements for WTORS that are intended to be used w
18、ith specific makes and models of wheelchairs. The belt-type occupant restraints may attach to the wheelchair such that occupant-restraint loads will be transferred through the wheelchair. This part of ISO 10542 applies to WTORS intended for use with children whose mass is greater than , in addition
19、to WTORS intended for use by adults. Children whose mass is less than should be transferred from their wheelchairs into appropriate child restraint systems intended for use in vehicles. The provisions of ISO 10542-1 apply except as amended and supplemented by this part of ISO 10542. ISO 10542-1 and
20、this part of ISO 10542 place particular emphasis on design requirements, performance requirements, and associated test methods with regard to the performance of WTORS for forward-facing wheelchairs and occupants in frontal impacts. Because this part of ISO 10542 addresses WTORS intended for use with
21、 specific makes and models of wheelchairs, the frontal impact test is conducted with a specific make or model of wheelchair, rather than with a surrogate wheelchair specified in ISO 10542-1. As such, the performance of both the WTORS and wheelchair are evaluated as a total system. Transportation-rel
22、ated requirements for wheelchairs that are suitable for adult occupant seating during motor vehicle transportation are specified in ISO 7176-19. 22 kg 22 kg 48-km/h Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/997
23、2545001 Not for Resale, 04/21/2007 11:10:49 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 10542-5:2004(E) ISO 2004 All rights reserved 1 Technical systems and aids for disabled or handicapped persons Wheelchair tiedown and occupant-restraint syst
24、ems Part 5: Systems for specific wheelchairs 1Scope This part of ISO 10542 specifies test methods as well as requirements for design and performance, for instructions and warnings to installers and users, and for product marking and labelling of wheelchair tiedown and occupant restraint systems (WTO
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 10542 2004
链接地址:https://www.31doc.com/p-3773843.html