ISO-10542-4-2004.pdf
《ISO-10542-4-2004.pdf》由会员分享,可在线阅读,更多相关《ISO-10542-4-2004.pdf(12页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO 10542-4 First edition 2004-09-15 Reference number ISO 10542-4:2004(E) ISO 2004 Technical systems and aids for disabled or handicapped persons Wheelchair tiedown and occupant-restraint systems Part 4: Clamp-type tiedown systems Assistances et aides techniques pour les perso
2、nnes invalides ou handicapes Systmes dattache du fauteuil roulant et de retenue de loccupant Partie 4: Systmes de fixation par crampon Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:47:17 MDT
3、No reproduction or networking permitted without license from IHS -,-,- ISO 10542-4:2004(E) ii ISO 2004 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the ty
4、pefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe
5、 Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unli
6、kely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including ph
7、otocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in S
8、witzerland Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:47:17 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10542-4:2004(E) ISO 2004 All rights reserved iii
9、Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a t
10、echnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters
11、 of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulate
12、d to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible
13、for identifying any or all such patent rights. ISO 10542-4 was prepared by Technical Committee ISO/TC 173, Assistive products for persons with disability, Subcommittee SC 1, Wheelchairs. ISO 10542 consists of the following parts, under the general title Technical systems and aids for disabled or han
14、dicapped persons Wheelchair tiedown and occupant-restraint systems: Part 1: Requirements and test methods for all systems Part 2: Four-point strap-type tiedown systems Part 3: Docking-type tiedown systems Part 4: Clamp-type tiedown systems Part 5: Systems for specific wheelchairs Copyright Internati
15、onal Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:47:17 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10542-4:2004(E) iv ISO 2004 All rights reserved Introduction Providing effectiv
16、e crash protection for the wheelchair-seated occupant of a motor vehicle usually requires that equipment be installed to secure the wheelchair and restrain the occupant of the wheelchair. ISO 10542-1 gives general requirements for all wheelchair tiedown and occupant-restraint systems (WTORS). The pr
17、ovisions of ISO 10542-1 apply except as amended and supplemented by this part of ISO 10542 which gives particular requirements and test procedures for WTORS and their sub-assemblies and components that use a mechanical clamp-type system to secure the wheelchair in a vehicle. Copyright International
18、Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:47:17 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 10542-4:2004(E) ISO 2004 All rights reserved 1 Technical syste
19、ms and aids for disabled or handicapped persons Wheelchair tiedown and occupant-restraint systems Part 4: Clamp-type tiedown systems 1Scope This part of ISO 10542 specifies test methods and requirements for design and performance, instructions to installers and users, and product marking and labelli
20、ng of wheelchair tiedown and occupant-restraint systems (WTORS). It is applicable only to WTORS that use clamp-type tiedown to secure wheelchairs when used as a forward facing seat by an adult passenger or driver of a motor vehicle. This part of ISO 10542 is applicable primarily to complete WTORS, b
21、ut a portion of this part of ISO 10542 can also be applied to components and sub-assemblies sold separately and for replacement parts. This part of ISO 10542 is applicable to WTORS intended for use with all types of manual and powered wheelchairs, including scooters with three or more wheels. 2Norma
22、tive references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 10542-1:2001, Technical syste
23、ms and aids for disabled or handicapped persons Wheelchair tiedown and occupant-restraint systems Part 1: Requirements and test methods for all systems 3Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 clamp-type tiedown method of wheelchair tie
24、down or securement that uses only mechanical linkages and/or grips requiring manual positioning and tensioning of the end fittings to the wheelchair 3.2 wheelchair securement adaptor hardware that is attached temporarily or permanently to the wheelchair frame to accommodate wheelchair securement by
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 10542 2004
链接地址:https://www.31doc.com/p-3773877.html