ISO-10683-2000.pdf
《ISO-10683-2000.pdf》由会员分享,可在线阅读,更多相关《ISO-10683-2000.pdf(14页珍藏版)》请在三一文库上搜索。
1、Reference number ISO 10683:2000(E) ISO 2000 INTERNATIONAL STANDARD ISO 10683 First edition 2000-07-15 Fasteners Non-electrolytically applied zinc flake coatings lments de fixation Revtements non lectrolytiques de lamelles de zinc ISO 10683:2000(E) PDF disclaimer This PDF file may contain embedded ty
2、pefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not inf
3、ringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were op
4、timized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2000 All rights reserved. Unless otherwise specified,
5、no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case pos
6、tale 56 ? CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2000 All rights reserved -,-,- ISO 10683:2000(E) ISO 2000 All rights reservediii ContentsPage Foreword.iv 1Scope 1 2Normative references1 3Terms and definition
7、s .2 4General characteristics.2 5Dimensional requirements and testing .2 6Testing of corrosion protection.5 7Mechanical and physical properties and testing5 7.1General5 7.2Appearance 5 7.3Temperature resistance 5 7.4Ductility.6 7.5Adhesion/cohesion 6 7.6Cathodic protection6 7.7Torque/tension relatio
8、nship for coatings with integral lubricant or subsequently (externally) added lubricant.6 8Applicability of tests6 8.1General6 8.2Tests mandatory for each lot.6 8.3Tests to be conducted for in-process control6 8.4Tests which are only to be conducted when specified by the customer.6 9Designation 7 10
9、Ordering requirements7 Annex A (informative) 8 -,-,- ISO 10683:2000(E) iv ISO 2000 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normal
10、ly carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the
11、 work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technica
12、l committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent ri
13、ghts. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 10683 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 1 Mechanical properties of fasteners. Annex A of this International Standard is for information only. -,-,-
14、 INTERNATIONAL STANDARDISO 10683:2000(E) ISO 2000 All rights reserved1 Fasteners Non-electrolytically applied zinc flake coatings 1Scope This International Standard specifies requirements for thickness, corrosion resistance and mechanical and physical properties of non-electrolytically applied zinc
15、flake coatings on steel fasteners with metric threads. It applies to both coatings with or without chromate. Coatings according to this International Standard may also be applied to steel screws which form their own mating threads such as wood screws, self tapping screws, self drilling screws, threa
16、d cutting screws and thread rolling screws as well as to non-threaded steel parts such as washers and pins. They may be similarly applied to steel fasteners with other types of thread. Coatings according to this International Standard can be supplied with integral lubricant and/or with a subsequentl
17、y added lubricant. 2Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However,
18、 parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
19、maintain registers of currently valid International Standards. ISO 898-1:1999, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs. ISO 965-1:1998, ISO general purpose metric screw threads Tolerances Part 1: Principles and basic data. ISO 965-2:199
20、8, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality. ISO 965-3:1998, ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional screw threads. ISO 1463:1), Metallic and ox
21、ide coatings Measurement of coating thickness Microscopical method. ISO 1502:1996, ISO general purpose metric screw threads Gauges and gauging. ISO 2064:1996, Metallic and other inorganic coatings Definitions and conventions concerning the measurement of thickness. 1)To be published. (Revision of IS
22、O 1463:1982) ISO 10683:2000(E) 2 ISO 2000 All rights reserved ISO 3269:2000, Fasteners Acceptance inspection. ISO 8991:1986, Designation system for fasteners. ISO 9227:1990, Corrosion tests in artificial atmospheres Salt spray tests. ISO 15330:1999, Fasteners Preloading test for the detection of hyd
23、rogen embrittlement Parallel bearing surface method. 3Terms and definitions For the purpose of this International Standard, the definitions given in ISO 2064 together with the following apply. 3.1 non-electrolytically applied zinc flake coating (with or without integral lubricant) coating which is p
24、roduced by applying to the surface of a fastener a zinc flake dispersion, possibly with the addition of aluminium flakes, in a suitable medium which under influence of heat (curing) generates a bonding amongst flakes and also between flakes and substrate thus forming an inorganic surface coating suf
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 10683 2000
链接地址:https://www.31doc.com/p-3773948.html