ISO-10692-1-2001.pdf
《ISO-10692-1-2001.pdf》由会员分享,可在线阅读,更多相关《ISO-10692-1-2001.pdf(22页珍藏版)》请在三一文库上搜索。
1、Reference number ISO 10692-1:2001(E) ISO 2001 INTERNATIONAL STANDARD ISO 10692-1 First edition 2001-08-15 Gas cylinders Gas cylinder valve connections for use in the micro-electronics industry Part 1: Outlet connections Bouteilles gaz Raccords pour robinets de bouteilles gaz pour lindustrie de la mi
2、crolectronique Partie 1: Raccords de sortie Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 03:39:05 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO
3、 10692-1:2001(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downlo
4、ading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the G
5、eneral Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address gi
6、ven below. ISO 2001 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs membe
7、r body in the country of the requester. ISO copyright office Case postale 56 ? CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2001 All rights reserved Copyright International Organization for Standardization Provided
8、 by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 03:39:05 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10692-1:2001(E) ISO 2001 All rights reservediii ContentsPage Foreword.iv 1Scope 1 2Normative references1 3Ge
9、neral requirements1 4General design.2 5Dimensions.2 6630 and 640 series connections.2 7710 and 720 series connections.6 8Components common to both series10 9Thread profile.12 10Allocation of outlet to single gases listed in annex A .12 11Allocation of other gases and of gas mixtures to outlets .13 A
10、nnex A (normative) Mandatory outlet allocations for selected single gases.14 Annex B (informative) Examples showing how to use the information given in clauses 10 and 1116 Bibliography17 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Tec
11、hnical Standards 1/9972545001 Not for Resale, 04/19/2007 03:39:05 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10692-1:2001(E) iv ISO 2001 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national stan
12、dards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International org
13、anizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given
14、 in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility
15、 that some of the elements of this part of ISO 10692 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. InternationalStandardISO 10692-1waspreparedbyTechnicalCommitteeISO/TC 58,Gascylinders, Subcommittee SC 2, Cylinder fittings. ISO
16、10692 consists of the following parts, under the general title Gas cylinders Gas cylinder valve connections for use in the micro-electronics industry: Part 1: Outlet connections Part 2: Specification and type testing for valve to cylinder connections Annex A forms a normative part of this part of IS
17、O 10692. Annex B is for information only. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 03:39:05 MDTNo reproduction or networking permitted without license from IHS -,-,- INTER
18、NATIONAL STANDARDISO 10692-1:2001(E) ISO 2001 All rights reserved1 Gas cylinders Gas cylinder valve connections for use in the micro-electronics industry Part 1: Outlet connections 1Scope This part of ISO 10692 applies to the outlet connections of gas cylinder valves for gases and gas mixtures and c
19、oncerns special requirements where the highest levels of cleanliness and freedom from particles are demanded for the manufacture of microelectronic components or similar applications. 2Normative references The following normative documents contain provisions which, through reference in this text, co
20、nstitute provisions of this part of ISO 10692. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 10692 are encouraged to investigate the possibility of applying the most recent editions of
21、 the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 68-2, ISO general-purpose screw threads Basic profile Part 2: Inch screw threa
22、ds. ISO 6506-1, Metallic materials Brinell hardness test Part 1: Test method. ISO 10156, Gases and gas mixtures Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets. ISO 10297, Gas cylinders Refillable gas cylinder valves Specification and type testing. I
23、SO 10298, Determination of toxicity of a gas or gas mixture. ISO 11114-1, Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials. 3General requirements 3.1Materials The following materials and specifications are recommended: ?For valve
24、and nipple: AISI 316L, microfinished, hardness at least 130 HBW in accordance with ISO 6506-1; ?For the union nut: AISI 304, threading silver plated. Other materials and values may be chosen if they give at least equivalent performance in terms of yield stress and resistance to corrosion (see ISO 11
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 10692 2001
链接地址:https://www.31doc.com/p-3773966.html