ISO-10691-2004.pdf
《ISO-10691-2004.pdf》由会员分享,可在线阅读,更多相关《ISO-10691-2004.pdf(12页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO 10691 First edition 2004-08-15 Reference number ISO 10691:2004(E) ISO 2004 Gas cylinders Refillable welded steel cylinders for liquified petroleum gas (LPG) Procedures for checking before, during and after filling Bouteilles gaz Bouteilles rechargeables soudes en acier pou
2、r gaz de ptrole liqufi (GPL) Modes opratoires de contrle avant, pendant et aprs le remplissage Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:47:57 MDTNo reproduction or networking permitted
3、without license from IHS -,-,- ISO 10691:2004(E) ii ISO 2004 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to
4、 and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the soft
5、ware products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it i
6、s found, please inform the Central Secretariat at the address given below. ISO 2004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permissi
7、on in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland Copyright International Organiz
8、ation for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:47:57 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10691:2004(E) ISO 2004 All rights reserved iii Contents Page 1Scope 1 2Normative references
9、 1 3Terms and definitions 1 4Segregation of cylinders prior to filling . 2 4.1General . 2 4.2Cylinders suitable for filling . 2 4.3Cylinders to be periodically inspected 3 4.4Cylinders requiring further assessment . 3 5Reassessment of cylinders . 3 6Filling 5 6.1Safe filling quantity . 5 6.2Safe fil
10、ling mixture and composition 5 6.3Accuracy of weighing equipment 5 6.4Filling methods 5 7Post-filling checks . 6 7.1Check of filled amount 6 7.2Action necessary for overfilled cylinders . 6 7.3Check for leakage 6 7.4Check of valve caps or plugs . 6 Bibliography . 7 Copyright International Organizati
11、on for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:47:57 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10691:2004(E) iv ISO 2004 All rights reserved Foreword ISO (the International Organization for
12、 Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the
13、right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Internatio
14、nal Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication a
15、s an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. I
16、SO 10691 was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 4, Operational requirements for gas cylinders. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:47:57 MDTN
17、o reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 10691:2004(E) ISO 2004 All rights reserved 1 Gas cylinders Refillable welded steel cylinders for liquified petroleum gas (LPG) Procedures for checking before, during and after filling WARNING This Interna
18、tional Standard calls for the use of substances and procedures that can be injurious to health if adequate precautions are not taken. It refers only to technical suitability and does not absolve the user from legal obligation relating to health and safety at any stage. It has been assumed in the dra
19、fting of this International Standard that the execution of its provisions is entrusted to appropriately qualified and experienced people. Where judgments are called for it has been assumed that they will be made by competent persons who have been trained specifically for the task. 1Scope This Intern
20、ational Standard specifies the procedures to be adopted when checking transportable refillable welded steel LPG cylinders before, during and after filling. It applies to transportable refillable welded steel LPG cylinders of water capacity from up to and including . It does not apply to cylinders pe
21、rmanently installed in vehicles, or to plant and filling equipment. 2Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu
22、ment (including any amendments) applies. ISO 10464, Gas cylinders Refillable welded steel cylinders for liquefied petroleum gas (LPG) Periodic inspection and testing 3Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 competent authority any natio
23、nal body or authority designated or otherwise recognized as such for any purpose in connection with this International Standard 3.2 competent body person or corporate body, defined by the national or relevant authority, which by combination of appropriate qualification, training, experience and reso
24、urces is able to make objective judgments on a subject 3.3 competent person person who by a combination of training, experience and supervision is able to make objective judgments on a subject 0,5 l 150 l Copyright International Organization for Standardization Provided by IHS under license with ISO
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 10691 2004
链接地址:https://www.31doc.com/p-3773985.html