ISO-10983-1999.pdf
《ISO-10983-1999.pdf》由会员分享,可在线阅读,更多相关《ISO-10983-1999.pdf(22页珍藏版)》请在三一文库上搜索。
1、A Reference number ISO 10983:1999(E) INTERNATIONAL STANDARD ISO 10983 First edition 1999-09-01 Timber structures Solid timber finger-jointing Production requirements Structures en bois Aboutages entures multiples de bois massif Exigences de fabrication Copyright International Organization for Standa
2、rdization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 04:49:26 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10983:1999(E) ISO 1999 All rights reserved. Unless otherwise specified, no part of this pu
3、blication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case postale 56 CH-1211 Genve 20 Switzerland Internetisoiso.ch Printed
4、 in Switzerland ii Contents 1 Scope1 2 Normative references1 3 Terms and definitions .1 4 Symbols2 5 Requirements.3 5.1 General.3 5.2 Timber3 5.3 Adhesives3 5.4 Characteristic strength.3 6 Manufacturing requirements 4 6.1 Production conditions4 6.2 Timber4 6.3 Adhesive application4 6.4 Assembly and
5、end pressure4 6.5 Preservative and fire retardant treatment 5 7 Quality control5 7.1 Factory production control5 7.2 Organization of factory production control .7 7.3 Documentation of the quality control system .8 7.4 Inspection and testing8 8 Type testing Initial determination of joint strength.8 8
6、.1 General.8 8.2 Materials 8 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 04:49:26 MDTNo reproduction or networking permitted without license from IHS -,-,- ISOISO 10983:1999(
7、E) iii 8.3 Preparation of specimens9 8.4 Procedure9 8.5 Characteristic strength 9 Annex A (informative) Finger-joint bending strength10 Annex B (informative) Finger-joint tension strength.13 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA
8、 Technical Standards 1/9972545001 Not for Resale, 04/19/2007 04:49:26 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 10983:1999(E) ISO iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO membe
9、r bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmenta
10、l and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directi
11、ves, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 10983 was prepared by Technical C
12、ommittee ISO/TC 165, Timber structures. Annexes A and B of this International Standard are for information only. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 04:49:26 MDTNo re
13、production or networking permitted without license from IHS -,-,- ISOISO 10983:1999(E) v Introduction This International Standard is based on European Standard EN 385:1995, Finger-jointed structural timber Performance requirements and minimum production requirements, but has been modified for intern
14、ational use. In particular, the requirements for external control of production by an external independent organization have been omitted, as this is regarded as the responsibility of national regulatory bodies and not a matter for inclusion in an International Standard. However, TC 165 is not prepa
15、red to recommend the use of finger joints in structural timber components where the manufacturing process is not described by a works quality manual for the following reasons. a) Structural properties can only be assigned to a finger joint which is clearly defined. Such definition requires a clear s
16、tatement, within the works quality manual, which details the raw material inputs (wood and adhesive) and the manufacturing process. b) Processes which are not written in a works quality manual and promulgated to the personnel responsible for manufacturing the finger joint are unlikely, over lengthy
17、periods of time, to be manufactured consistently. Other principles built into the development of this International Standard are as follows. This International Standard applies only to the finger-joint production and makes reference only to the maintenance of finger-joint strength. Finger joints are
18、 found in both glulam laminations and finger joints and finger-jointed timber used directly for structural applications. No attempt is made in this International Standard to relate compliance testing to the properties of either glulam or finger-jointed timber. Type testing is undertaken to establish
19、 characteristic strengths and thence target strengths for compliance (daily quality control) testing. The precise test configurations are not specified in this International Standard, which permits the use of a wide variety test equipment. However, it is a requirement that the same equipment and con
20、figuration used for type testing also be used for compliance testing. Both bend and tension tests are provided for compliance testing. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/
21、2007 04:49:26 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 04:49:26 MDTNo reproduction or networking
22、permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISOISO 10983:1999(E) 1 Timber structures Solid timber finger-jointing Production requirements 1 Scope This International Standard specifies requirements for bonded finger joints and minimum requirements for the manufacture of cut, inter
23、locking, bonded finger joints in structural timber members. Although most finger joints are produced in coniferous species, this International Standard also applies to broad- leaved species where information is available to enable them to be satisfactorily bonded. It does not cover impressed (die-fo
24、rmed) joints. In the case of glued laminated timber it applies only to individual laminations. Large finger joints in glued laminated timber are not covered by this International Standard. 2 Normative reference The following normative document contains provisions which, through reference in this tex
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 10983 1999
链接地址:https://www.31doc.com/p-3774050.html