ISO-11064-3-1999.pdf
《ISO-11064-3-1999.pdf》由会员分享,可在线阅读,更多相关《ISO-11064-3-1999.pdf(42页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 I 1 064-31999 TECHNICAL CORRIGENDUM 1 Published 2002-02-01 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION MWYHAFODHAF OPrAHHwMn no CTAHLIAPTMWHM ORGANISATION INTERNATIONALE DE NORMALISATION Ergonomic design of control centres - Part 3: Control room layout TECHNICAL CORRIGE
2、NDUM 1 Conception ergonomique des centres de commande - Partie 3: Agencement de la salle de commande RECTIFICATIF TECHNIQUE 1 Technical Corrigendum 1 to International Standard IS0 11064-3:1999 was prepared by Technical Committee ISOTTC 159, Ergonomics, Subcommittee SC 4, Ergonomics of human-system i
3、nteraction. Page 71 Figure 5 In the key, replace the text for c and d with the following: C d 500 = clearance under the luminaire 2 O00 = body height, including clothing allowance ICs 13.180 O IS0 2002 -All rights reserved Printed in Switzerland Ref. No. IS0 11064-3:1999/Cor.l:2002(E) I NT E R NAT I
4、 O N AL STANDARD IS0 11 064-3 First edition 1999-1 2-1 5 Ergonomic design of control centres - Part 3: Control room layout Conception ergonomique des centres de commande - Partie 3: Agencement de la salle de commande “This material is reproduced from IS0 documents under International Organization fo
5、r Standardization (ISO) Copyright License Number HIS/CC/1996. Not for resale. No part of these IS0 documents may be reproduced in any form, electronic retrieval system or otherwise, except as allowed in the copyright law of the country of use, or with the prior written consent of IS0 (Case postale 5
6、6,121 1 Geneva 20, Switzerland, Fax +41 22 734 10 79), IHS or the IS0 Licensors members. Reference number IS0 11 064-3: 1999( E) o IS0 1999 -,-,- STD-IS0 31064-3-ENGL 1799 4853703 0833294 745 ISOIFDIS 11064-311 999(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Ad
7、obes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing polic
8、y. The IS0 Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of lhe software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every ca
9、re has been taken to ensure that the file is suitable for use by IS0 member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. o IS01999 All rights reserved. UnleSS otherwise specified, no pari of this publication m
10、ay be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IS0 at the address below or ISOs member body in the country of the requester. IS0 copyright office Case postale 56 CH-1211 Geneva 20 Tel
11、. + 41 22 749 O1 11 Fax +41227341079 E-mail copyrighiiso.ch Web www.iso.ch Printed in Switzerland ii 0 IS0 1999 -All rights reserved Contents STD-IS0 11064-3-ENGL 1999 = 4853903 0833295 BL IS0 11064-3:1999(E) 1 2 3 4 4.1 4.2 4.3 4.4 4.5 4.6 Scope . Normative references . Terms and definitions . Ergo
12、nomic design of control centres Process for control room layout . General considerations for control room layout ArchitecturaVbuilding recommendations Workstation arrangements . Shared visual displays, off -workstation Personnel circulation and maintenance access . Annex A: Examples of control room
13、layout Annex 6: Anthropometric data of the world population: . Bibliography Page 1 1 1 5 5 6 9 13 15 17 22 34 35 8 IS0 1999 . All rights resewed . 111 -,-,- STD-IS0 11064-3-ENGL 1999 4BCL903 0833296 7LB IS0 11 064-3: 1 999(E) Foreword IS0 (the International Organization for Standardization) is a wor
14、ldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on
15、 that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commis- sion (IEC) on all matters of electrotechnical standardization. International Standard are drafted
16、 in accordance with the rules given in the ISOAEC Directives, Part 3. Draft International Standards adopted by the technical Committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Att
17、ention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. IS0 shall not be held responsible for identifying any or all such patent rights. International Standard IS0 11064-3 was prepared by Technical Committee ISO/TC 159, Ergonom
18、ics, Subcommittee SC 4, Ergonomics of human-system interaction. IS0 11064 consists of the following parts, under the general title Ergonomic design of control centres: - Part I: Principle for the design of control centres. - Part 2: Principles of control suite arrangement - Part 3: Control room layo
19、ut - Part 4: Workstation layout and dimensions - Part 5: Displays and controls - Part 6: Environmental requirements for con fro1 centres - Part 7: Principles for the evaluation of control centres - Part 8: Ergonomic requirements for specific applications Annexes A and B of this part of IS0 11 064 ar
20、e for information only. iv Q IS0 1999 - All rights reserved Introduction This part of IS0 11 064 establishes ergonomic requirements, recommendations and guidelines for control room lay- out. User requirements are a central theme of this part of IS0 11064 and the processes described are designed to t
21、ake account of needs of users at all stages. The overall strategy for dealing with the user requirements as strategy to be adopted for control room design is presented in IS0 11064-1. IS0 11064-2 provides guidance on the design and planning of the control room in relation to its supporting areas. Re
22、quirements for the design of workstations, displays and controls and the physical working environment are pre- sented in IS0 11064-4 to IS0 11064-6. Evaluation principles are dealt with in IS0 11064-7. IS0 11064-1 to IS0 11064-7 cover general principles of ergonomic design appropriate to a range of
23、industries and service providers. The specific requirements appropriate to particular sectors or applications areas are covered in IS0 11064-8. The requirements presented in IS0 11064-8 are to be read in conjunction with IS0 11064-1 to The ultimate beneficiaries of this part of IS0 11064 will be the
24、 control room operator and other users. It is the needs of these users that provide the ergonomic requirements used by the developers of International Standards. Although it is unlikely that the end user will read this part of IS0 11064, or even know of its existence, its application should provide
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 11064 1999
链接地址:https://www.31doc.com/p-3774072.html